Discrete Component Testers
check connected individual semiconductor components.
-
Product
Automated Surface Inspection for Glossy Components
-
Flawlessly glossy surfaces are among the most important quality features of many premium products. The smallest surface defects immediately have a degrading effect on the product. The result: disappointed end customers or buyers. At the same time, reflective surfaces are often very sensitive and a challenge for optical metrology. A manual inspection is tedious, expensive, and ultimately always governed by subjective decision criteria. During production, faulty painting or coating processes can cause high scrap rates. Defects that are not detected even during the final inspection can lead to expensive complaints and, in the worst case, to the loss of the customer. Only an efficient, automated surface inspection achieves the highest quality at acceptable costs.
-
Product
Lightwave Component Analyzers (LCA)
-
The Lightwave Component Analyzer is the instrument of choice to test all relevant opto-electronic S-parameters, like S21, S11 and S22 for electro-optical components in 10Gb/s and 40Gb/s, Fibre Channel and CATV transmission systems as well as radio-over-fiber and A&D applications.
-
Product
Discrete Module for Multi Protocol 4000 Boards
-
Discrete Module for Multi Protocol 4000 BoardsThe M4KDiscrete is an interface module for the multimode, multiprotocol Excalibur EXC-4000 family of carrier boards. The M4KDiscrete provides a complete solution for developing and testing discrete voltage-level interfaces.The module contains control I/O registers that may be accessed in real time. The module supports 20 discretes. The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels and• Either enable or disable external debounceOutput discretes are open collector, capable of handling up to 32V with a maximum current of 100 mA each. There is a 4092 word FIFO, capable of storing 1023 Discrete entries containing the discrete data and Time tags.
-
Product
PXI Infrastructure PXI Mainframe / Components
OTP2 module no.182
Mainframe
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
Assure Component Counter
-
Assure & Assure Pro Intelligent Simple Fast Trustworthy Assure is the fastest, simplest and most reliable way to implement live component inventory management into your organization. Intelligent, simple, fast, and trustworthy, Assure enables you to increase productivity and minimize component shortage downtime. Assure™ Pro simplifies the reel counting workflow by automatically reading the reel’s barcode ID with an integrated camera.
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, Receiver
310113285
Protective Cover
When the Receiver is not in use, the Protective Cover is used to protect the modules and contacts. The Protective Cover is made up of black anodized aluminum.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
-
Product
Optical Component Test
-
Test and characterize modern optical components, including photonic integrated circuits (PICs) and silicon photonics, with unmatched speed, precision and accuracy. Accelerate and improve your design or optimize your production with Luna’s suite of component analyzers and testers.
-
Product
32-CH Discrete Input Modules with U Profile
HSL-DI32-UD
Digital Input Module
HSL U series is designed as compact & horizontal-placed slave module. For I/O module, ADLINK adopts three types of connectors to meet different users' requirements & habits. Compared with past models, U series brings compact size, easier-to-wire and cost-effective advantages for users. DI/O, AI/O and motion control module are supported
-
Product
Component Testers
-
After a wafer is tested through front-end test and back-end test, the component tester tests this final component or package assuring its quality for the semiconductor makers. DDR, DDR2, DDR3 memory component testers.
-
Product
Control Components
-
From power supplies to counters to temperature controllers, we have all needed components for a successful and complete automation solution.
-
Product
Computer Based Audio Component Test System
DATS V3
-
Rugged aluminum housing with detachable test leads and built-in precision calibration resistorTighter tolerances on internal components for more precise measurementsIncreased output capability means greater separation from the noise floor, resulting in more accurate measurementsDATS Linearity Test for comparing parameters and impedance plots at multiple drive levelsOptional under desk mounting brackets included to save desk spaceOnly 1" H x 2-1/2" W x 4-1/8" D for easy portability
-
Product
PLD/PED Components
-
Neocera offers a variety of components that can be fitted and combined into new or existing PLD and PED systems to provide improved functionality and enhanced capability. Components include:*Oxygen-compatible substrate heaters for epitaxial oxide film depositions..*Automated Target Carousels for preparing multilayer heterostructures.*Deposition chambers design specifically for PLD and PED systems.*Manual and automated laser window-change Accessories.*Pulsed Electron Deposition (PED) sources for laser transparent materials.*Ideal for retrofitting existing systems or construction of new systems.
-
Product
IPD RF Components – LTCC
-
Pulse’s complete offering of LTCC based Band Pass Filters, Balun’s, Diplexer’s and Couplers used in conjunction with our wireless antenna products will enhance your devices performance keeping attenuation and noise to a minimum. Many of Pulse’s IPD components are already qualified or referenced on various radio designs, so please contact us about the components already qualified on the radio you are using. From Wifi Networking devices, to smart phones and tablets, Pulse’s offering of IPD Components has you completely covered. Using the table below you can search our complete IPD Component offering.
-
Product
32-CH Discrete Output Daughter Board Module
HSL-DO32-DB-N
Digital Output Module
*Slave ID consumption: 2 - N: for 32-CH NPN sinking type outputs*Photo couple isolation voltage: 2500Vrms*Output switching capacity: Single channel 500mA; all channels 60mA at 24VDC*Output response time:ON OFF: 180µs, OFF ON: *1.2µsTerminal Base:HSL-TB64 or HSL-TB32U-DIN
-
Product
68-Pin SCSI Micro-D Male Discrete Wire
40-962-068-M
-
This connector is designed to allow users to directly terminate with IDC connections to the 68-Pin SCSI Style Micro D connector. Pickering Interfaces recommends the use of purchased cable assemblies for applications where most or all of the contacts are in use.
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
Digital Input Module
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
Component Test Systems
Test System
These products include test peripherals used with test systems, such as interfaces that connect semiconductor devices with test systems, and handlers that transport semiconductors to the test system. System-level test equipment and software are also included in this category.
-
Product
Optical Components
-
ZYGO Corporation was founded in 1970 by Paul Forman, Sol Laufer, and Carl Zanoni with the vision to become the premier manufacturer of plano optical components through the application of innovative polishing methods. We have realized our founders vision, and further expanded our manufacturing offering beyond plano optical components to include coatings, aspheres, freeforms and complex optical systems.
-
Product
RF & Microwave Passive Components
-
SHF Communication Technologies AG
SHF’s microwave components are broadband devices suitable up to 110 GHz. Our SHF BIAS TEES are well known but perhaps a slight variation does suit your application even better. DIPLEXERS are bias tees with a certain bandwidth in the low frequency path to combine or separate high frequency and low frequency signals into or out of a single line. DC-FEEDERS are bias tees without the capacitor. Therefore, it provides slightly lower insertion loss in case it is connected to an AC-coupled device which already has a capacitor on its input. Based on our air line construction, these passive components provide resonance-free transmission over the entire operating range.
-
-
Product
X-Ray Components
-
Photonis designed the Micro Pore Optics detector to be used in X-Ray imaging applications. Its perfectly square, flat channels are optimized to allow X-Ray and UV photons to be focused or collimated due to the total external reflection at a grazing angle (<2°). Micro Pore Optics are installed on a number of international space missions.
-
Product
Fiber Optic Components For Optoelectronic Packaging
-
OZ Optics offers a wide range of standard and custom fiber optic components for optoelectronic packaging. Components include collimators, focusers, patchcords, connectors, and metalized fiber. The low backreflection collimators and focusers are available for a wide range of industry-standard connectors and wavelengths. The hermetically sealable patchcords, with glass or metal solder, and metalized fiber meet high Telcordia standards. The polarization maintaining patchcords and connectors use our specially designed ferrules that minimize insertion loss, backlash, and rotational errors.
-
Product
Design and Development: Complete Systems and System Components
-
Custom Systems Integration Inc.
CSI''s design and development (D&D) organization has the resources, skill and experience to design a complete turnkey system, a system component or collaborate with customer''s internal staff on any part of a system.
-
Product
Optical Components for Custom Spectroscopy
-
HORIBA offers a wide variety of optical accessories. We have optical choppers which pulse continuous light sources. Explore our order sorting filter wheels for spectrographs and monochromators. Choose from our optical fibers and light guides, with flexible light delivery, single fibers, fiber bundles, and liquid light guides. And select from our lens and mirror-based sample compartments.All of these accessories are compatible with our various optical components. Our optical accessories allow us to complete a custom solution for your unique configuration requirements and a variety of spectroscopy applications. HORIBA offers more choices to ensure you can select the best optics for your needs.
-
Product
Sensors, Probes And Coils For Component Testing
Sensors
-
Foerster Instruments, Incorporated
We offer a comprehensive range of standard and customised sensors, probes and coils for component testing. If the wide selection of standard sensors does not optimally solve your testing task, we offer you an individual new development specially adapted to your testing task. Thanks to our many years of experience, you receive reliable sensor technology for reproducible test results.
-
-
Product
3U OpenVPX Multichannel Discrete I/O Board
68DT1
Multifunction I/O
The 68DT1 is a 3U OpenVPX™ board featuring up to 96-Channels of Standard Functionality (SF) DT1 module-type or Enhanced Functionality (EF) DT4 module-type Discrete I/O functions [foptioned, factory configurable].48-Channels are dedicated as input (voltage or contact sensing with programmable, pull-up/pull-down current sources). An additional 24 or 48-Channels are programmable for either input or output (current source, sink, or push-pull) switching up to 500 mA per channel from an applied 3 – 60 V external VCC source (or sink to ISO-GND). The 68DT1 can sense broken input connections and whether an input is shorted to +VCC or to ground. Additional features of the DT4 EF are listed below. The 68DT1 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for pull-up resistors or mechanical jumpers.
-
