Discrete Component Testers
check connected individual semiconductor components.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Protective Cover, 9050, VXI and Discrete Wiring, Receiver
310113285
Protective Cover
When the Receiver is not in use, the Protective Cover is used to protect the modules and contacts. The Protective Cover is made up of black anodized aluminum.
-
Product
Test & Measurement Equipment And RF Components
-
Is necessary for the design, test, manufacture, and debug of radio frequency devices.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module with US Type Connector
HSL-DI16DO16-US
-
*16-CH digital input and 16-CH digital output*Shrounded-type connector*Isolation Voltage: 2500Vrms*Higher output current up to 90mA/channel*Easy installation and wiring
-
Product
32-CH Discrete Output Modules with U Profile
HSL-DO32-UD
-
*UD type is suitable for screw type wiring. Each wire to sensors or actuators can be fixed by the screw terminal*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitation and cost-effective requirement*Support 32 DO channels*Transmission speed: 3/6/12 Mbps
-
Product
Swept Test System For Optical Components
-
measurement platform for optical components with a fastscan speed, high resolution and accuracy. The systemcombinesour tunable lasers, polarization controller, power meter and software.
-
Product
The Portable Solution for your On-Site Component TestsHE PORTABLE SOLUTION FOR YOUR ON-SITE COMPONENT TESTS
TESTERLYZER® Mobil Pilot
-
The TESTERLYZER® Mobil Pilot is a robust test unit for vehicle control units in an integrated system, which is easy to transport. The case is produced individually in line with customer requirements regarding size and integration depth.
-
Product
Microwave Components
-
We are a worldwide leader in the design, development and manufacture of radio-frequency and microwave components, and our product portfolio is one of the most comprehensive anywhere in the world.Our magnetrons, performance monitors, low noise front ends, circulators, loads, limiters and receiver protectors are trusted to power every type of commercial radar application, including airborne, navigation and guidance devices, radar and sonar equipment and electronic surveillance systems.
-
Product
Module Retainer Block Set, For Discrete Wiring, 2 Positions
510109117
Mounting Kit
These module retainer blocks are used to attach modules directly to the inner frame of a VXI receiver for discrete wiring. These modules hinge down with the receiver to provide easy access to wiring.
-
Product
Wound Component EST Analyzer
19036
-
Chroma Systems Solutions, Inc.
The industry’s first Wound Component Electrical Safety Test (EST) Analyzer that combines impulse winding, AC/DC hipot, insulation resistance and DC resistance test measurement functions. Chroma’s 19036 Wound Component EST Analyzer has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement with a maximum output of up to 40 channels. Capable of outputting and measuring AC100mA/DC 20mA, Chroma’s 19036 is suitable for testing to high power motor standards such as UL 1004-1.
-
Product
Pipework Components & Hydraulic Equipment
-
Walter Stauffenberg GmbH & Co. KG
For more than 50 years, the companies of STAUFF Group have been developing, manufacturing and distributing pipework equipment and hydraulic components for mechanical and plant engineering and for service and industrial maintenance.
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
-
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
ITA, 9050, 50 Module, VXI and Discrete Wiring, Double Tier
410104538
ITA
The 50 module ITA can be used in a number of applications to accomplish the required connection to the Unit Under Test (UUT). You can mount a VPC front or rear mount enclosure or customize your own fixture to be attached on the frame. A wide range of ITA modules are available separately for user configuration.
-
Product
Passive Components
-
Narrow and broadband, tailored cut-off frequencies and slope, electronically controllable, high-Q factor, highly linear transfer characteristics
-
-
Product
Combination Module: 2 Ch. MIL-STD-1553 & 12 Ch. Discrete I/O
CM8
-
The CM8 module is a combination of NAI's MIL-STD-1553B module, FTB, and Enhanced Discrete I/O module, DT4. The CM8 offers twelve channels of discrete I/O and two channels of MIL-STD-1553B communications. The twelve discrete I/O channels are programmable as either input (voltage or contact sensing with programmable, on-module pull-up/pull down current sources), or output (current source, sink, or push-pull) up to 500 mA per channel from an applied, external 3-60 VCC source. The discrete I/O channels also provide additional functionality modes such as Pulse Width Modulation (PWM) output mode and Pattern Generator output mode. The two MIL-STD-1553B communications channels feature a dual, redundant, balanced-line, physical layer; a (differential) network interface; time division multiplexing; half-duplex command/response protocol; and up to 31 remote terminals (devices).
-
-
Product
Pitot Static Tester / AoA TESTER
ADSE 744
-
This tester was specifically designed for the new-generation pitot tubes that integrate sensing probes, pressure sensors and powerful air data computer processing to provide all critical air data parameters including Pitot and static pressure, airspeed, altitude, and angle of attack. This Pitot Static tester is designed primarily for flightline use to cover the testing of all barometric and manometric pressure instrument systems. The AoA Channel behaves as a second Ps channel, in order to create a differential pressure between the 2 Ps Channel, allowing to performsimulations of different Angles of Attack. The large touch screen display, with on-screen help, enables all checks to be carried out easily on the flight deck or in the cockpit, by a single operator. The ADSE 744 is robust and housed in amobile weatherproof case. An attached bag contains the pressure hoses and electrical cables.
-
Product
Battery Tester
-
Shenzhen Graigar Technology Co.,Ltd.
A battery tester is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition.
-
Product
Mechanical Tester
UMT TriboLab
-
Bruker’s Universal Mechanical Tester (UMT) platform has been the most versatile and widely used tribometer on the market since the first model debuted in 2000. Now, newly designed from the ground up, the UMT TriboLab™ builds on that legacy of versatility with a unique modular concept that harnesses more functionality than ever before—all without any compromise in performance.
-
Product
Surge Testers
MTC 2
-
Advanced automatic high precision electrical winding testers for testing products like alternators, stators, transformers, armatures and motors. Available as static or portable units from 6-50 kV.
-
Product
HIPOT testers
HypotMAX III
-
Patented SmartGFI® functionStorage of 50 test setupsRemote Safety InterlockUSB/RS-232 or GPIB interfaces availableAdvanced menu driven controlDigitally controlled arc detection systemCHARGE LO® & RAMP HI® systems
-
Product
Radome Tester
QAR50
-
The R&S®QAR50 is the ideal tool for accurately testing the quality of automotive radomes and bumpers in the automotive radar frequency range at the end-of-line (EOL). It features sufficient space to easily accommodate bulky bumpers combined with spatially resolved measurements to evaluate the homogeneity of design emblems.
-
Product
In-Circuit Tester
Eagle MTS180
-
The Eagle offers low testing cost for high volume with even the most complex fixture applications. Equipped with a Press-Down-Unit and a combination of analog and hybrid In-Circuit test pins, the MTS180 is in a class for its own. Furthermore, the tester can be equipped with functional test modules to provide even higher fault coverage and thus satisfy the test requirements of a larger number of customers.
-
Product
120 GBd High-performance BERT
M8050A
Bit Error Rate Tester (BERT)
The Keysight M8050A high-performance bit error ratio tester (BERT) enables accurate characterization of receivers used in next-generation data center networks and server interfaces. With uncompromised signal integrity, support for NRZ, PAM4, PAM6, and PAM8 signals, and data rates up to 120 GBd, the flexible architecture of the M8050A supports 1.6T pathfinding as well as other leading-edge technologies.
-
Product
Signal, Module, ID, CASS, 210 Position, Discrete Wiring
510114106
ITA Module
Module, ID, Cass, Signal, 210 Positions, Discrete Wiring
-
Product
6-CH Discrete Input 16-CH Discrete Output Module with UD Type Connector
HSL-DI16DO16-UD
-
*Supports 16 DI channels and 16 DO channels*Transmission speeds: 3/6/12 Mbps*RJ-45 phone jack for easy installation*Compact and single board design to meet space limitati
-
Product
DIP Tester
Model DS-10
-
Putting it a conveyor to flow through a solder bath to obtain information needed to manage it. The created temperature profile makes it possible to monitor the 50ms sampling temperature of the preheat and solder temperature sensors in addition to the conventional management items.
-
Product
LED Testers
-
PeakTech Prüf- und Messtechnik GmbH
An extremely practical component tester for LEDs and other components. The device outputs an automatically raised output voltage between 0 to 300 V DC, which adapts to the connected load so that the sensitive components are not destroyed. Particularly suitable for the service and repair workshop.
-
Product
Leak Tester
LSD-01A
-
Jinan Leading Instruments Co., Ltd.
LSD-01A Leak Tester is applicablein leak testing of pouches, bottles, pipes, cans and boxes of foodstuff,pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It’ s also applicable in the leak testing ofthe specimens after falling tests and pressure resistance tests.
