SPI
assures volume and area of paste application.
-
product
Arduino CAN Shield
IFB-10003-ANP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
ARINC 429 Card
SET-1623
The SET 1623 ARINC Card has 32 Tx/Rx Channels. These 32 Tx/Rx channels are structured in 4 banks (P0.x to P3.x) 8 channels each. Each bank is controlled by a dedicated SPI (SPI0 to SPI3) located on RTI.
-
product
Logic Analyzer & Digital Pattern Generator
ScanaQuad Series
ScanaQuad (SQ) is a series of high performance 4 channels logic analyzers and digital pattern generators. They are designed to be your best companion when working on serial protocols like UART, SPI, I2C, 1-Wire, USB, I2S, CAN, LIN, RS232, RS485, and more. With ScanaQuad Logic Analyzers, you can capture signals, you can play them back, and you can even build genuine test signals and generate them!
-
product
Multipurpose Debug Board
DB40 Debug Module
The DB40 Debug Card is designed for debugging of COM Express and PC/104 boards. It includes the following features: - Port 80/81 decoding for Power On Self Test (POST) via LPC - Interface to SPI Flash for BIOS update - Interface to Board Management Controller (BMC) for update - Power and Reset buttons and status LEDs The DB40 Debug card can only be used on products that have the appropriate FFC debug connector designed for this purpose. (Includes DB40 Debug Module, two 40-pin FFC cables, and 14-pin cable for SP100 DediProg USB to SPI programmer.)
-
product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
product
AOI/SPI Inspection Systems
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises AOI/SPI Inspection Systems
-
product
72 channel FPGA Logic Module
XLM72
XLM72 is a FPGA based logic module with 72 I/O ports. Featuring two 64 Mbit SPI (Serial Peripheral Interface) memories, from one of which its FPGA boots upon power-up, complex logic operations can be programmed and saved on-board.
-
product
Standard Serial Page EEPROM
Serial Page EEPROM is a high-density, page-erasable SPI EEPROM memory that combines flexibility, performance, and ultra-low power. The Serial Page EEPROM with proprietary NVM cell technology delivers fast erase/write performance with high cycling endurance and robust retention. The new architecture allows fast wake up and byte flexibility, as well as block management and fast quad output, while keeping current surge and energy budget at very low levels.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-T
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
product
3D SPI Series
MS-11e
- Exclusive15MP / 25MP CoaXPress Camera System- Dual Projection Shadow Free Moiré Technology- Precision Compound Telecentric Camera Lens- Automated Z-Height Calibration System- Automated PCB Under Board Support System- Precision PCB Warpage Compensation- Closed Loop Communication With Screen Printer- Absolute Repeatability and Reproducibility- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
product
Universal Relay Driver Control - PXIe, 32 Channel Direct Relay Drivers
33011
PXI-e based universal relay control for semiconductor load boards, 32CH direct relay drivers, 2 lanes of SPI relay control interface
-
product
SparkFun Qwiic Micro:bit Breakout (with Headers)
The SparkFun Qwiic micro:bit Breakout is a board that connects to the BBC micro:bit and expands the capabilities of the development platform by providing access to more pins and allowing for connections to the I2C and SPI buses. We've already attached headers to this version of the board so you don't need to worry about any soldering! This breakout board for the micro:bit’s edge connector allows intermediate and advanced users to connect the micro:bit to breadboards and other Qwiic sensors, motors, LEDs and more!
-
product
Firmware for High-speed HDLC/SPI Communications (NEW Version)
OP-FW12G
This expansion firmware increases the baud rates of bit synchronous communications (e.g., HDLC/SDLC/X.25, and CC-Link communications). The firmware processes main measurement items completely with a field programmable gate array (FPGA), thus precisely capturing communications data along with time stamps in 1-µs units.
-
product
3D Solder Paste Inspection system
PI Series
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
product
Logic Analyzer
LAP-16064U
Zeroplus Technology Corperation
Sample rate (Internal clock): 100MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Channels may be selectively defulted to /Channels: 16 CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals. Glitch Capture Capability: 5ns. Bandwidth: 75MHz.
-
product
Narrow Band Filters (Single Octave)
NANO-POLE® Series
The NANO-POLE® is designed for optimal size, DC consumption, RF power handling, insertion loss, signal purity and linearity. The NANO-POLE® provides a minimum center frequency step size of 10 MHz typically but can be modified based upon request. The NANO-POLE® requires a +3.0 V supply that typically draws 5 mA when not hopping. The supply voltage should be adequately filtered as noise present on this pin will influence the RF signal purity. The NANO-POLE® uses SPI control interface.
-
product
Dual Band Block Up-Converter
DBUC Series
*Connectorized Package *Wide Choice of Frequency Ranges *Dual Band *Integrated Filters *Gain Control *CAN, RS-232, I2C, or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
Arduino CAN Shield
IFB-10003-AWP
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
product
ESI Test Jig
MS 1543
This Test System designed to test the analog, discrete, Ethernet, RS232, RS422, Synchro /Resolver and SPI Signals. It is standalone test equipment and has GUI ATP Software interface with laptop/PC through RS232/Ethernet Interface.
-
product
Relay Test Set Type SP-I
Supreme Instrument Laboratories
Supreme make relay testing set is designed for site testing of protective relays which simulate in common fault conditions under which a protective relay will be called into positive function. Periodic field testing is the best way of ensuring the integrity of the protective relays. We offer our relay testing set with specific testing capacity to suit different group of protective relays. The testing set operates on single phase 230 V, A.C. 50Hz. Supply.
-
product
AOI & SPI, Test Systems
SigmaX SPI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The SigmaXs inspection technology is unaffected by varying materials, surface conditions, or colors. The system profiles the board to generate accurate 3D shapes far superior to other brands and technologies.
-
product
Xilinx Zynq ARM + FPGA SoM
TE0715-7015
Sundance Multiprocessor Technology Ltd.
TE0715s are industrial-grade Xilinx Zynq-7000 System on Modules with 4 MGT Links , a gigabit Ethernet transceiver, 8 Gbit (1 Gbyte) DDR3 SDRAM with 32-bit width, 32 Mbyte SPI Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os is provided via rugged high-speed stacking strips.
-
product
Low speed Serial Interfaces
12C/ 12S/ SPI/ UART
Arasan has a diverse portfolio of connectivity IP products including SPI, I2C, I2S and UART. These protocols are vital for the integration of SoCs with peripheral chipsets in order to form a complete hardware platform. They are frequently used by the SoC to configure, control and gather diagnostic information at the platform level to ensure correct operation of the hardware.Arasan's proven Connectivity IP Solutions provides a risk free path to integrating these interfaces in SoC designs:High quality IP cores ensure inter-operability between SoCs and peripheralsIn-house domain expertise ensures a high quality support throughout the SoC development cycleTotal IP solution includes RTL source code, synthesis scripts, test environment and documentation
-
product
LoRa 1W Breakout
915M30S
Do you need power? This breakout for the 915M30S module from EBYTE is a 1W (30dBm) LoRa transceiver. LoRa is great for long range (miles), low power (in sleep), and low data rates (~500bps). This breakout board is designed to connect to any platform that has SPI and 6 available GPIO. We include a robust edge mount RP-SMA connector to connect large LoRa (915MHz) antennas. In addition, the on-board U.FL connector can be used if you need to get outside a metal enclosure.
-
product
AOI & SPI Test Systems
To keep the quality of your production at its best you need a good inspection of your boards. For efficient and detailed in-depth board inspection ensure you have SMT inspection equipment that meets your needs. Our AOI & SPI units will provide the quality you need for reliable inspection of soldering inspection.
-
product
Bridge Device and GPIO Port Expander
SPI-to-I2C
The CP2120 compact SPI-to-I2C bridge and general purpose port expander device can be easily added to a system to solve interface compatibility problems and add more GPIO when required.
-
product
Advanced All-in-One Bluetooth® Analysis System
Vanguard
The most advanced, most comprehensive Bluetooth protocol analyzer ever made. Building on a legacy of innovation, the Bluetooth Vanguard All-In-One Protocol Analysis System delivers new advances designed to ease the increasingly complex tasks of Bluetooth developers. Vanguard provides synchronized capture and analysis of BR/EDR, Bluetooth Low Energy, Wi-Fi 802.11 a/b/g/n/ac (3x3), WPAN 802.15.4 (all 16 2.4 GHz channels), raw 2.4 GHz RF spectrum analysis, HCI (USB, UART, SPI), generic SPI/UART/I2C/SWD communications, WCI-2, logic signals, and Audio I2S.
-
product
True Phase Identification System
SPI-III™
Our vision has always been to create a phase identification system that exceeds any of today’s industry quality, safety and efficiency requirements. SPI-III’s unique design consists of a wireless bi-module combo that is stunningly easy to configure and operate. With many advancements and innovations, SPI-III will be more helpful than ever before, enabling field applications such as identification of A-B-C electrical phases from all 50 and 60 Hz networks, switchgear phase concordance (matching), phase rotation, system paralleling, underground phasing applications and more.
