SPI
assures volume and area of paste application.
-
Product
Xilinx Zynq ARM + FPGA SoM
TE0715-7015
-
Sundance Multiprocessor Technology Ltd.
TE0715s are industrial-grade Xilinx Zynq-7000 System on Modules with 4 MGT Links , a gigabit Ethernet transceiver, 8 Gbit (1 Gbyte) DDR3 SDRAM with 32-bit width, 32 Mbyte SPI Flash memory for configuration and operation, and powerful switch-mode power supplies for all on-board voltages. A large number of configurable I/Os is provided via rugged high-speed stacking strips.
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
AOI/SPI Inspection Systems
-
Dou Yee Enterprises (S) Pte Ltd
Dou Yee Enterprises AOI/SPI Inspection Systems
-
Product
Ultra-Low Power Computing Module
CM22303
-
LinkedHope Intelligent Technologies Co.,Ltd.
CM22303 uses Intel® 7th generation Kaby Lake-Y platform and Core M Ultra low-power SoC processors, and integrates the full functions of CPU, GPU and South/North Bridge on a single chip. The processor provides powerful computing and display performance with dual-core and four threads configuration. Its turbo frequency can boost up to 3.6 GHz and the display output resolution can be up to 4K. CM22303 has an amazing thermal design power consumption of only 4.5W (TDP) and can be used for a variety of high-performance fanless designs. SPI BIOS is designed on board to support dual-channel low voltage on board memory (up to 16GB), Gigabit Ethernet, TPM module and other functions. With high-performance and low power consumption, it can be widely used in the field of low power embedded systems. Meanwhile, CM22303 adopts COM Express standard and is compatible with Type10 pin out definition, and also provides rich peripheral interfaces such as USB3.0/2.0, PCIe, SATA, HD Audio etc.
-
Product
SparkFun MicroSD Transflash Breakout
-
Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested.
-
Product
USB Protocol Analyzers
Beagle Series
-
Our line of Beagle Protocol Analyzers provide real-time visibility into I2C, SPI, and USB systems making them ideal tools for embedded engineers.The Beagle analyzers provide high-performance bus monitoring in a small, portable package that includes cross-platform software support making it perfect for engineers in the field and in the lab.
-
Product
72 channel FPGA Logic Module
XLM72
-
XLM72 is a FPGA based logic module with 72 I/O ports. Featuring two 64 Mbit SPI (Serial Peripheral Interface) memories, from one of which its FPGA boots upon power-up, complex logic operations can be programmed and saved on-board.
-
Product
Digital Temperature Sensors
-
Analog Devices offers a broad selection of digital temperature sensors with I2C, SPI, and mark space interfaces. For more intricate system design applications, some of these sensors have integrated D/A converters, A/D converters, references, and limit alarm register. All of these sensors possess a broad range of uses, including scientific, medical, and aerospace applications, in test and measurement equipment, and in industrial automation.
-
Product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
-
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
Product
Serial I/O Boards
-
Serial Mode Protocols include Asynchronous, Bisync, SDLC, HDLC, IEEE 802.3, Synchronous Telemetry, Simple Clock/Data ("-SYNC" product line), Di-phase and SPI Interface. Transceiver support RS485, RS422 (V.10), RS232 (V.28), RS423, V.35, RS530, as well as other software selectable mixed protocol modes Up to Eight Independent Serial Channels per Board Synchronous Serial Data Rates up to 10 Mbits/sec Asynchronous Serial Data Rates up to 1 Mbits/sec PMC and cPCI rear I/O support Custom Protocols Available
-
Product
IO60-DIO48 Module
IO60-DIO48
Module
WINSYSTEMS’ IO60-DIO48 Module adds GPIO to embedded systems with IO60 expansion featuring 48 GPIO (General Purpose Input-Output) tolerant to 30 V DC. The SPI interface is implemented through the MACH XO2 SPI-slave EFB (Embedded Function Block) interface. Each bit of each port is implemented as a bi-directional tristate driver. Each bit of each port can also be configured and enabled to detect rising and/or falling edge events and generate a system interrupt.
-
Product
Multi Protocol Analyzer
LE-2500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-J
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
USB-8452, 3.3 MHz I2C, 50 MHz SPI I2C/SPI Interface Device
781964-03
Interface Module
The NI USB‑8452 is a master interface for connecting to and communicating with inter-integrated circuit (I2C) and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8452 is a bus-powered, portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices, toggling LEDs, or strobing convert and data ready lines common to analog converter chips. You can physically place the USB‑8452 more closely than PCI interfaces to I2C/SPI devices, which reduces I2C bus length and minimizes noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
Arduino CAN Shield
IFB-10003-IWP
-
CAN (Controller Area Network) communication has become ubiquitous in industry. It is used in automotive applications (part of OBD and many other datalinks), on-highway trucks (J1939), industrial machinery and instrumentation, and equipment applications (factory automation). This shield is designed to provide a CAN 2.0 front-end interface for 5V Arduino modules (Uno, Mega, etc). The module uses SPI to communicate to the Arduino, and requires an aditional chip select pin. An optional interrupt line to the MCP2515 and two LEDS are also provided. The chip select and interupt lines are selected via zero ohm resistors and have several configuration options for flexibility stacking additional shields. A set of stackable headers is included with this board, not installed. An optional on-board voltage regulator may be used to supply 7.5V to the Arduino's 'Vin' pin (which is regulated to 5V by the Arduino's on-board LDO). The CAN shield regulator supports a wide input range of 9V to 32V. This makes it possible to cleanly build a stand-alone CAN node (remote sensor) without the need for a separate Arduino power supply!
-
Product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
-
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
Product
ContactLAB Spy
-
Laboratory class spy and protocol analyzer for easy, non-intrusive capture and analysis of communication between contact cards and readers using SWP, ISO 7816, SPI and I2C protocols.
-
Product
COM Express Type 7
ROM-8720
-
Advantech ROM-8720 COM Express Type 7 Compact Computer-on-Module is powered by NXP LS1046A SoC which includes four Arm Cortex-A72 cores for Edge networking and Edge firewall, two 10Gbsp-KR and up to four Gbps for the networking communications. Three PCIe, three USB 3.2 Gen1 and three USB2.0 for the embedded interface expansions. two UART, one SPI and 8 GPIO for embedded device controls.
-
Product
MAX31855 T-Type Thermocouple Arduino Shield
SEN-30004-T47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino.
-
Product
Miniature Spectrometer
Ocean HDX
-
Ocean HDX is anchored by High Definition Optics for high throughput, low stray light and great thermal stability. Its X-Platform Electronics include powerful onboard processing and communications including Gigabit Ethernet, SPI and Wi-Fi. The Ocean HDX is compact, robust and ideal for integrated, industrial and research applications.
-
Product
SparkFun Micro OLED Breakout
-
The SparkFun Micro OLED Breakout Board breaks out a small monochrome, blue-on-black OLED. It’s "micro", but it still packs a punch – the OLED display is crisp, and you can fit a deceivingly large amount of graphics on there. This breakout is perfect for adding graphics to your next Arduino project, displaying diagnostic information without resorting to serial output, and teaching a little game theory while creating a fun, Arduino-based video game. Most important of all, though, is the Micro OLED is easy to control over either an SPI or I2C interface.
-
Product
Low Speed Protocol Decode/Trigger Software (I2C, SPI, RS232, I2S, JTAG)
D9010LSSP
-
This bundle includes powerful decoding and triggering for the following serial bus standards: I²C, SPI, Quad SPI, eSPI (including Quad eSPI), RS232/UART, Manchester, I²S, SVID, and JTAG (IEEE 1149.1). It is compatible with S-Series, V-Series, Z-Series, EXR-Series, MXR-Series, UXR-Series, 9000 Series, and 90000 Series Infiniium oscilloscopes. For detailed information on the decode and trigger settings, please refer to the datasheet.
-
Product
Universal ByteBlaster
SKU-002-01
-
The Universal ByteBlaster supports target systems ranging from 1.2V to 5V. The ByteBlaster supports Altera, Xilinx, Lattice, and Atmel FPGA/CPLDs (selectable via 4-position dip-switch), and implements Master 2IC or SPI functionality. The ByteBlaster’s functionality can me customized and adjusted to support customer’s special needs.
-
Product
3D SPI Series
MS-11e
-
- Exclusive15MP / 25MP CoaXPress Camera System- Dual Projection Shadow Free Moiré Technology- Precision Compound Telecentric Camera Lens- Automated Z-Height Calibration System- Automated PCB Under Board Support System- Precision PCB Warpage Compensation- Closed Loop Communication With Screen Printer- Absolute Repeatability and Reproducibility- INTELLISYS® Industry 4.0 Intelligent Factory Automation System
-
Product
MAX31856 Thermocouple Sensor Arduino Shield
SEN-30007-T
-
Quad channel thermocouple Arduino shield based on the MAX31856 universal digital thermocouple interface IC. This is an exciting update of the MAX31855, with improvements in resolution (19 vs 14 bits), on-board temperature reference (6 vs 4 bits), and compensation (fully compensated vs nonlinear correction required). The MAX31856 is interfaced via 4-wire SPI with options for interrupt triggering. An LDO and a high-speed level shifter are included on ALL device pins to allow interfacing with to any Arduino - both 3.3V and 5.0V variants - without sacrificing device performance in any operating condition.
-
Product
Logic Analyzer
LAP-16128U
-
Zeroplus Technology Corperation
Sample rate (Internal clock): 200MHz asynchronous operation. Sample rate (External clock): 100MHz synchronous operation. Channels may be selectively defulted to /Channels: 16 CH. Upgrade Oscilloscope to measure and decode I2C / UART (RS232C & RS485) / SPI Protocols and mixed signals.
-
Product
Multipurpose Debug Board
DB40-HPC Debug Module
-
The DB40-HPC Debug Card is designed for debugging of COM-HPC modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Firmware for High-speed HDLC Mode
OP-FW10R
-
OP-FW10R is a firmware to expand the measurement speed for bit synchronous communication such as HDLC/SDLC/X.25, CC-Link and SPI communication up to 10Mbps. Processing major part of the measurement process by FPGA, it enables capturing of communication data with time stamp of micro-second unit.
