SPI
assures volume and area of paste application.
-
Product
SPI Isolators
-
SPI (Serial peripheral interface) is one of the most widely used interfaces between microcontrollers and peripheral ICs such as sensors, ADCs, DACs, shift registers, SRAM, and others. Analog Devices has your isolated SPI bus covered with our dedicated SPI digital isolators which support this synchronous, full duplex master-slave-based interface. Options include devices built with ADI's proven iCoupler® technology and offering a small footprint, simple design-in, fast speeds, and high data integrity, as well as integrated µModules which require no external components. Our SPI isolator solutions increase performance and reduce board space. This simple, compact solution is ideal for isolated SPI data requiring communication across different ground potentials or through large common mode transients often found in Industrial PLCs (programmable logic controllers) and Instrumentation and data acquisition systems.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-50
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
Interface Module
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
Product
I²C/SPI Interface Device
Interface
The I²C/SPI Interface Device is a master or slave interface for inter-integrated circuit (I²C), or master interface for serial parallel interface (SPI) devices. With plug-and-play USB connectivity, the I²C/SPI Interface Device is a portable solution to communicate with consumer electronics and integrated circuits. The I²C/SPI Interface Device can be physically located more closely to I²C/SPI devices than PCI interfaces, reducing I²C bus length and minimizing noise problems. The I²C/SPI Interface Device supports I²C rates up to 250 kHz and SPI rates up to 50 MHz, and it also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I²C devices or toggling LEDs.
-
Product
Triple-Axis Accelerometer (+-2g/4g/8g/16g) w/ I2C/SPI
ADXL345
-
Filling out our accelerometer offerings, we now have the really lovely digital ADXL345 from Analog Devices, a triple-axis accelerometer with digital I2C and SPI interface breakout. We added an on-board 3.3V regulator and logic-level shifting circuitry, making it a perfect choice for interfacing with any 3V or 5V microcontroller such as the Arduino.
-
Product
3D Solder Paste Inspection (SPI)
TR7007 SII
-
Offering inspection speeds of up to 200 cm2/sec, the TR7007 SII is the fastest solder paste inspection system in the industry. This highly accurate inline shadow-free solder paste inspection solution offers full 3D inspection at resolutions of 15 µm or 10 µm. Built on a high precision linear motor platform, the system's hallmark features include closed loop function, enhanced 2D imaging, auto-warp compensation and fringe pattern technology. Increase capacity without sacrificing additional space with an available dual-lane configuration.
-
Product
SPI Flammability Tester (Vinyl Material)
TF318
-
TESTEX Testing Equipment Systems Ltd.
SPI Flammability Tester (Vinyl Material), to determine the ignition properties of vinyl plastic film material according to CFR 16 Part 1611 U.S.A. Flammable Fabrics Act for flammability of apparel vinyl plastic film.The rate of burning shall not exceed 1.2 in./s as judged by the average of five determinations lengthwise and five determinations transverse to the direction of processing, when specimen is placed at an angle of 45 degree and expose to the standardized flame (22# fire nozzle, 1/2 inch. In length).
-
Product
Robust RISC-based DIN-rail Fanless Embedded System With I.MX 6UL Processor, COM, SPI, I2C, 2 LANs And DIO (2-in/1-out)
IFB125
-
The IFB125 is powered by the low-power Freescale i.MX6UL processor in the ARM® Cortex™-A7 micro architecture. It supports extended operating temperature ranging from -40°C to 70°C, and can withstand vibration up to 5G. Its flexible wide voltage range 9V - 48V DC power input with a lockable terminal block type connector also enhances its reliability in harsh environments. To meet most of Industrial IoT needs, the IFB125 supports multiple communication interfaces for maximum flexibility, including LAN, serial, USB, and digital I/O ports. The Industrial IoT gateway has 256MB onboard memory that features data transfer rates of DDR3-1600, as well as 4GB eMMC flash memory onboard for storage. This embedded IoT gateway platform is equipped with one PCI Express Mini Card slot and one SIM card slot. Additionally, it supports DB9 connectors with both SPI and I2C function as communication protocols to suit for specific applications
-
Product
Insertion Flow Meter
SPI Mag
-
The SPI Mag Insertion Flow Meter provides a highly cost-effective solution for the accurate measurement of liquid flow in closed conduit, pressurized pipe applications. Unlike conventional magnetic meters, the SPI Mag's cost is independent of pipe size.
-
Product
Process Improvement Software for SPI & AOI
SIGMA Link
-
SIGMA Link software suite links altogether solder paste inspection (SPI), automated optical inspection (AOI) and manufacturing execution system (MES). For Smart Factories, SIGMA Link is the essential element to connect inspection machines to Manufacturing Execution System. This real-time interface ensures full traceability and enables interlocking of machines to automate SMT lines while driving yield to new levels.
-
Product
Universal Relay Driver Control - PXIe, 32 Channel Direct Relay Drivers
33011
Relay Driver
PXI-e based universal relay control for semiconductor load boards, 32CH direct relay drivers, 2 lanes of SPI relay control interface
-
Product
Embedded Serial Triggering and Analysis for InfiniiVision DSOX1000 Series Oscilloscopes
DSOX1EMBD
-
The IC, SPI, and UART/RS-232 serial decode option for InfiniiVision 1000 X-Series oscilloscopes (DSO models) displays responsive, time-aligned, on-screen decode of Inter-Integrated Circuit (IC), 3-wire Serial Peripheral Interface (SPI), and UART/RS232 serial communication buses. Because it is hardware-based, this option provides the fastest throughput solution for triggering on and analyzing IC, SPI and UART/RS-232 serial buses found in a wide variety of embedded designs.
-
Product
3D Solder Paste Inspection Machine (3D-SPI)
3Si Series
-
Saki's 3D SPI identifies critical defects and assists with process improvement.
-
Product
Multiplying Current Output D/A Converters
-
Analog Devices offers a wide range of high precision, multiplying current output (IOUT) D/A converters (DACs) that feature ±1 LSB INL and DNL specifications, from 12-bit up to an industry-leading 18-bit resolution. Our portfolio includes single and multiple D/A converters in small packages with parallel or serial SPI interfaces. Multiplying current output R-2R D/A converters allow for an external amplifier that’s optimized for specific applications and that does not require reference buffering, which enables high linearity. The SoftSpan™ feature allows software selectable output spans, therefore eliminating the need to add precision gain stages and the associated external jumpers, precision resistors, and amplifier circuitry. Integrated precision resistors allow for reference inversion, bipolar offset, and offset and gain adjustment.
-
Product
SparkFun MicroSD Transflash Breakout
-
Breakout board for the microSD socket that is not much bigger than your fingernail. Compatible with the SPI interface found on any SD card, this tiny form factor was created for cell phone storage and is perfect for your next MP3 project! Board comes fully assembled and tested.
-
Product
BMC Card
SOM-RM10
-
ASPEED 7th Gen AST2600 BMC Card, OCP RunBMCv1.5 ASPEED 7th Gen AST2600 Server Management Processor. Up to 2GB DDR4 on-board, 128MB SPI flash on-board, 1GbE LAN for mainly connectivity & VGA 800x600 for easier on-site debug.
-
Product
SparkFun TFT LCD Breakout
1.8" (128x160)
-
The SparkFun TFT LCD Breakout is a versatile, colorful, and easy way to experiment with graphics or create a user interface for your project. With a 4-wire SPI interface and microSD card holder, you can use this breakout to easily add visual display/interface capabilities to a project as well as providing all the storage you might need for multimedia files.
-
Product
3D Solder Paste Inspection system
PI Series
-
PI Series is a new generation 3D Solder Paste Inspection system that overcomes the limitations of traditional SPIs and satisfy all your inspection needs. The PI Series allows to easily implement Solder Paste Inspection in any PCBA line. These new generation systems are very intuitive to use, allowing non-experienced persons to get expected results.
-
Product
Bridging And I/O Expansion Versatility. Rapid Hardware Acceleration For Improved Signal Control.
MachXO2
-
*Up to 256 kbits of user Flash memory and up to 240 kbits sysMEM™ embedded block RAM*Up to 334 hot-socketable IOs that avoid excess leakage*Programmable through JTAG, SPI, I2C or Wishbone*TransFR feature allows in-field design update without interrupting equipment operation*Programmable sysIO™ buffer supports LVCMOS, LVTTL, PCI, LVDS, BLVDS, MLVDS, RSDS, LVPECL, SSTL, HSTL and more
-
Product
USB/RS232/SPI Programmable Attenuator
RUDAT-13G-90
-
Mini-Circuits’ RUDAT-13G-90 is a general purpose programmable RF attenuator supporting frequencies from 10 to 13000 MHz with attenuation from 0 to 90 dB in 0.5 dB steps. Its unique design maintains linear attenuation change per dB, even at the highest attenuation and frequency settings. The attenuator is controlled via USB, RS232 or SPI. It comes housed in a compact, shielded metal case with SMA(F) input/ output RF ports (RF ports are interchangeable), a USB type Mini-B socket, and a 9-pin D-sub(F) RS232 and SPI port. Power can be supplied via either USB or the D-sub port. The RUDAT-13G-90 is supplied with our easy-to-install, user-friendly GUI software, API objects for Windows® environments, and complete programming instructions for 32 and 64 bit Windows® and Linux® operating systems. See p. 9 for a complete list of included accessories.
-
Product
Power Supply Support
-
Renesas offers a complete portfolio of system supervisory solutions ranging from single to quintuple (five) voltage monitors. In addition, the system management ICs are voltage monitors with small amounts of I2C or SPI software programmable EEPROM memory. Renesas single-chip sequencing solutions sequence up to four different voltages while providing other useful features such as voltage monitoring, fault protection, and reset assertion.
-
Product
Evaluation Board
emPower
-
SEGGER Microcontroller GmbH & Co. KG
The emPower eval board provides a comprehensive set of SEGGER's middleware products, accelerating the start of any embedded project. SEGGER's embOS real-time operating system is at the heart of the evaluation. Furthermore, evaluation versions of the file system emFile, graphics library emWin, emUSB Host & Device, and TCP/IP stack embOS/IP (including web server demo) enable full use of the available emPower peripherals. emPower also features a J-Link OB, an on-board version of SEGGER's market-leading debug probe J-Link, which includes drag & drop programming and COM-Port support. There are three expansion interfaces to easily connect additional modules. Each connector provides I2C, SPI, UART, GPIO/timer, analog input and power. A display adapter connector enables the connection of small TFT displays. The emPower board is powered by USB only. Current consumption drawn strongly depends on the application and connected peripherals. Idle consumption is approx. 85 mA.
-
Product
TTL/I2C/SPI* Expansion Kit
OP-SB5GL
-
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
Product
Block Up-Converter
BUC Series 5” x 2.5” x 0.6”
-
*Connectorized Package *Compact, Rugged Design *C, X, Ku, K, and Ka-Bands Available *L-Band Inputs (950-2150 MHz) *Internal or External Filters Available *Variable Attenuation Control via CAN +5V Logic, SPI, RS232, or I²C
-
Product
Universal ByteBlaster
SKU-002-01
-
The Universal ByteBlaster supports target systems ranging from 1.2V to 5V. The ByteBlaster supports Altera, Xilinx, Lattice, and Atmel FPGA/CPLDs (selectable via 4-position dip-switch), and implements Master 2IC or SPI functionality. The ByteBlaster’s functionality can me customized and adjusted to support customer’s special needs.
-
Product
ContactLAB Spy
-
Laboratory class spy and protocol analyzer for easy, non-intrusive capture and analysis of communication between contact cards and readers using SWP, ISO 7816, SPI and I2C protocols.
-
Product
MAX31855 J-Type Thermocouple Arduino Shield
SEN-30004-J47
-
Four channel MAX31855 digital thermocouple Arduino Shield. Two versions of this shield are avaliable for each thermocouple type: either 'Ch 0-3' (CS pins use Uno/Mega IO pins 7-10) or 'Ch 4-7' (CS pins use Uno/Mega IO pins 3-6), with the only difference being which set of zero-ohm resistors are populated on the board. This allows use of other SPI devices that may be 'hard coded' to specific digital pins on the Arduino, or simply stacking one of each type together to get a total of eight thermocouple channels on one Arduino. The MAX31855J supports a measured temperature range of -210C-1200C with known thermal characteristics and output resolution of 0.25C. Included thermocouple connectors are type-specific to provide proper material continuity as close to the IC as possible. The SEN-30004 is interfaced via 3 or 4-wire SPI and a high-speed level shifter is included to allow the board to plug directly into an Arduino Uno or Mega
-
Product
InfiniiVision Oscilloscopes
3000A X-Series
-
100 MHz to 1 GHz, DSO and MSO modelsView time-correlated digital content with16 digital channels (MSO)Modulate signals within the scope with WaveGen, built-in 20 MHz function generator (optional)Quickly characterize signals with the built-in 3-digit voltmeter and 5-digit counter option Decode serial busses faster with hardware-based serial analysis options for CAN, LIN, IC, SPI, RS232 and more Protect your investment with full upgradability
-
Product
Multichannel Voltage Output D/A Converters
-
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
-
Product
SparkFun Pressure Sensor Breakout
MS5803-14BA
-
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface. This MEMS pressure sensor measures the absolute pressure of the fluid around it which includes air, water, and anything else that acts like a viscous fluid. Depending on how you interpret the data, you can determine altitude, water depth, or any other tasks that require an accurate pressure reading. What makes the MS5803-14BA unique is the the gel membrane and antimagnetic stainless steel cap that protects against 30 bar water pressure.
