Amplifiers
increase the amplitude of a signal.
See Also: Amp, RF Amplifiers, Preamplifiers, Current Amplifiers, Audio Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
PCIe 14 Bit High Speed Digitizer - 500 MS/s on 4 Channels
M4I.4451-X8
The 6 models of the M4i.44xx-x8 Express series are designed for the fast and high quality data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels with 14 bit or 16 bit resolution without any phase delay between them. The card uses only one A/D converter even when running with 500 MS/s, guaranteeing best signal quality without any interleaving technology. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
product
Multiplexed- Low-Level Function Card
Low-level multiplexed systems have a single programmable gain, wide-band amplifier following the input multiplexer. To accommodate low-level signal signals such as those from strain gauges or thermocouples and at the same time high level signals from other sources, the throughput rate must be limited to enable the high bandwidth amplifier to settle to the correct value after switching to a new channel. This results in a relatively low aggregate throughput rate when compared to an amplifier-per-channel system. A major benefit of a well designed low-level multiplexed system is the extremely high performance/cost relationship.
-
product
Digital Quad-Phase "DSP" Lock-In Amplifier -
eLockIn203
The eLockIn203 can be used as spectrum analyser, as oscilloscope, as sinus generator or as measurement control system.
-
product
2-22 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5022
The HMMC-5022 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-22 GHz frequency range. Typical applications of the HMMC-5022 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-22 GHz frequency range.
-
product
8-Channel Amplifier and Low-Pass Filter Module
SCS-814
The SCS-814 and SCS-815 amplifier/filter module provides eight 8-pole low-pass filters that can be individually configured for a cutoff-frequency from 0.5Hz to 70kHz(SCS-814) and 0.5Hz to 60kHz(SCS-815). Each of the SCS-814/SCS-815's eight channels features an instrumentation amplifier with software-selectable gains of 1 to 1000 in 1-2-5 steps.
-
product
Amplifier Systems Band Specific
Systems are complete. They plug into an outlet and are ready to go. Our standard systems are 3U, which is 5.25″ and 5U, 8.75″. Systems are available with or without IEEE-488, RS-232 and Ethernet connectivity. Amplifiers Systems are available in both Broadband and Band-Specific frequencies. We are well-known in the industry for successfully adapting our amplifiers or custom designing new solutions to suit each unique project. Please refer to our Adapted & Custom Design Solutions link to begin formulating your performance objectives and other criteria.
-
product
4-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - 3U VPX
Model 52761
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four 200 MHz 16-bit A/Ds- Four multiband DDCs- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x4- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- 3U VPX form factor provides a compact, rugged platform- Compatible...show more -
product
Amplifiers
Amplifiers are used to amplify the energy output of photodetectors as well as convert their electrical signal for a number of illumination measurement or spectroscopy applications. Amplifiers are digital systems that amplify the low electrical current transmitted by photodetectors to easily detectable levels. Amplifiers also convert photodetectors' electrical current into voltage so that their signal may be read by other digital devices. Amplifiers are indispensable for nearly any light measurement applications by greatly increasing the usability of a detector system.
-
product
Bi-Directional Amplifier
Integrated dual directional amplifier offering high output power and low noise figure
-
product
RF POWER AMPLIFIERS
BLWA Series
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
product
Digital Miniature Multi Channel Analyzer
MCA 527
Baltic Scientific Instruments, Ltd
Automated base line restorer and threshold adjustmentAutomated or manual pole zero adjustment without oscilloscopeSystem dead time and count rate indicationDead time correctionAutomated spectrum recordingPeak stabilizationBasic analysis functions (energy calibration, FWHM, peak area and integral calculations, spectrum stripping and smoothing)File menu: write/read functions with drive/path - and file pick list functionsSetup menu: ADC, Amplifier, Presets, Memory splitting, MCA mode, MCS mode, Multi spectral recording mode, automated instrument configuration using setup file
-
product
Light-to-Analog Sensors (Voltage)
Renesas' light-to-voltage silicon optical sensors combine a photodiode array, a non-linear current amplifier and a micropower op amp on a single monolithic IC. Applications for these devices include display backlight control, keypad dimming, anti-glare mirror systems, and industrial and medical light sensing applications.
-
product
2-Ch 500 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-6 FPGA - 6U VPX
Model 57651
- Complete radar and software radio interface solution- Supports Xilinx Virtex-6 LXT and SXT FPGAs- Two 500 MHz 12-bit A/Ds- Two multiband DDCs (digital downconverters)- One DUC (digital upconverter)- Two 800 MHz 16-bit D/As- One multiboard programmable beamformers- Up to 2 GB of DDR3 SDRAM; or: 32 MB of QDRII+ SRAM- PCI Express (Gen. 1 & 2) interface up to x8- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- Optional LVDS co...show more -
product
Capacitive Sensors
Our separate sensor amplifiers allow an easy adjustment and interpretation of our capacitive sensor heads. For this purpose, both a compact comfort-amplifier and an IO-Link-amplifier for top hat rail mounting are available.
-
product
MOSFET Drivers
Renesas' product portfolio includes MOSFET gate drivers for 3-phase motor applications. The drivers have built-in detection/protection functions and are suitable for inverter driver applications such as EGR, HVAC and EPS. Line up the products with LDOs for MCU, 24V battery system capability, built-in current sense amplifiers, and motor angle detection function. The products support unit downsizing and high performance.
-
product
SMT & QFN Products
PMI offers custom surface mount (SMT) and QFN packaging for many types of devices. SDLVA's, Log Amplifiers, Phase Shifters, Attenuators, Switches, as well as Low Noise Amplifiers. PMI also offers multifunction options in a single QFN package such as Limiter / LNA or LNA / Detector. PMI has the experience to offer custom devices that meet your specific control function at high frequency. Mounting and integrating high frequency RF devices take skill and experience such that the package itself does not degrade the RF signal. PMI has the experience in selecting the proper package, integrating the RF devices and providing the required testing.
-
product
Signal Conditioners
Our load cell signal conditioners / amplifiers are just the thing when a digital display is not required, for example, applications in which the weighing system is controlled or monitored by a computer or PLC. These units supply the needed excitation voltage to power up the load cell(s). The wide range of models offered provide a variety of accuracy and frequency response levels, and signal outputs such as 0-10VDC, +/-10VDC, 4-20mA, RS232, RS485, USB, and frequency. Both AC & DC powered units are available.
-
product
RF Plasma Generators & Amplifiers
100 W to 2400 W 13.56 MHz Analog/Digital, RS-232, USB interfaces Low Harmonic Distortion Automatic and Manual Gain Control High Speed Pulsing (Bursting) controls Compatible with T&C''''s Matching Networks GUI Software (complete PC control) Includes all essential RF power/communication cables and mounting brackets Air cooled (Air & Water 1200 W +) Half rack mount or stand alone versions Ideal for: Industrial, Scientific, and Medical Applications
-
product
Headphone Amplifiers
Applied Research and Technolgy
Drive in-ear monitors, tap a speaker line when a monitor isn't available, and make sure the whole band can hear everything they need.
-
product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
product
TWT Amplifiers
dB Control designs and manufactures high-power microwave amplifiers, transmitters, high- and low-voltage power supplies and modulators for radar, electronic warfare (EW), electronic countermeasures (ECM) and data link applications. The modularity of our designs enables us to rapidly configure power products for custom applications. Our products can meet your specifications and platforms requirements for ground-based, shipborne and high-altitude military manned and unmanned aircraft.
-
product
High Voltage Amplifier
HA-800
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
product
Radiometer
X1-1-RCH-116-4
The X1-1 radiometer from Gigahertz-Optik features an RCH-116-4 detector and is ideal for measurement of the irradiance of high power LEDs in the UV-A and blue light range. The device can accurately measure irradiance levels of up to 40,000 mW/cm². One of the outstanding features of the RCH-116-4 detector is its proven concept of a passive radiation absorber coupled to a UV sensor. This provides stability even in high temperature and intense UV radiation environments. In addition to the passive r...show more -
product
8-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - 6U VPX
Model 58760
- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Four or eight 200 MHz 16-bit A/Ds- 4 or 8 GB of DDR3 SDRAM- PCI Express (Gen. 1, 2 & 3) interface up to x8- Sample clock synchronization to an external system reference LVPECL clock/sync bus for multiboard synchronization- Optional user-configurable gigabit serial interface- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Ruggedized and conduction-cooled versions available- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
product
Test System Optimized for High Throughput, Low Cost of Test for Single Site, Multi-site and Index Parallel Applications
ETS-88RF
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
product
16-Channel Instrumentation Amplifier
PGA-16
The PGA-16 is a 16-channel instrumentation amplifier with differential input, single-ended output, programmable AC or DC input coupling and pre-filter gain.
-
product
High Speed Amplifier
TI offers the industry's most comprehensive high speed amplifier portfolio with the widest bandwidth and best in class distortion, precision and power consumption across a broad range of supply voltages. Our industry leading FDA's, DVGA's, TIA's and General purpose amplifiers coupled with the reliability and longevity of our parts makes TI the ideal supplier of high speed amplifiers.
-
product
Light
Welcome to Thorlabs; below you will find links to light emitters, sources, and controllers, a subset of our entire line of photonics products. Our light sources are conveniently separated into coherent and incoherent sources. The coherent source category includes laser diodes, laser diode modules, tunable lasers, HeNe lasers, and femtosecond lasers, while the incoherent source link brings you to a selection of LEDs, white light, and broadband SLD sources. The Quantum Electronics category include...show more -
product
Motion Control Terminal Board For Panasonic MINAS A4 Servo Amplifiers
DIN-814-A40
- Panasonic MINAS A4 super servo- Dimensions: 123 mm x 107 mm x 44 mm (WxLxH)- Available for PCI-8174, PCI-8164, PCI-8154, PCI-8158 and PCI-8134
