White Light Interferometers
-
product
Light Logger Sesor
NUL-204
This sensor is very versatile with applications in many areas of the natural sciences. It can be used to study photosynthesis in biology, light-emitting chemical reactions in chemistry, the effect of changing voltage on a light-bulb's output in physics and more.
-
product
Short Light Source
LM-AS
The short light source is compatible with the LM-101 or the LMC-20. The light is supplied with a 50 watt tungsten halogen convection cooled light source which provides suffcient energy for use with narrow band pass filters or monochronomators in the wave length range of .35 to 2.5 microns. The light beam is chopped at 200 hz by a quiet, vibration free, synchronous motor. The housing also contains a secondary LED light source and detector for synchronization of the amplifier, plus an electro-mechanical shutter to block the light output when the instrument is zeroed. An internal collimating lens produces a narrow beam (<1") so the LM-AS can be used in bell-jar and large coating systems.
-
product
Light Initial Degradation Tester
King Design Industrial Co., Ltd.
Stable solar cells are needed for durability testing of different combinations of module ... cause, the focus fell on light induced degradation (LID) .... module using the same cells as in the initial modules was used.
-
-
product
Light Booths
Konica Minolta Sensing Americas, Inc
Konica Minolta’s Light Booth products provide accurate results when inspecting a range of unique products including inks, paints, plastics, textiles, paper and colorants. Light booths simulate lighting conditions which allows testing in a multitude of different lighting conditions. This allows for incredibly precise color measurements in a spectrum of different lights and angles.
-
product
Light and Energy Meter
Model 659
UV Light and Energy Meter for use with all wafer steppers. For over 45 years, OAI is a world leader in UV Light and Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries. The New Model 659 is an advanced UV exposure analyzer specifically designed for use with all wafer steppers including high intensity wafer steppers. This meter averages up to 400 exposure readings, has Ethernet and USB interface for downloading recorded measurements, and has intensity range of up to 7,500mW/cm2. Probes are available in wavelength of 365nm, 400nm, 420nm & 436nm. OAI has a complete certified calibration lab to maintain the performance, quality and reliability of our meters. The Model 659 meter is traceable to NIST standards.
-
product
Signal Light for Hipot Testers
LX-signal light-HV1
2-color indicator light, red, green.With the help of the signal light tower, you can visualize potentially high voltage.
-
product
Light Distribution Photometer Goniophotometer
LCG-1600
Shenzhen Chuangxin Instruments Co., Ltd.
LCG-1600 Goniophotometeric System carries out measuring methods of fixed location and rotating luminaires. The measured luminaire is installed on the two-dimension rotating table, using “+” laser to make the luminaire lighting center superposed with the rotating center of rotating table. The mechanical equipment allows turning the tested luminaires around a vertical axis and a horizontal axis. When tested luminaires turn around horizontal axis, the detector which is at the same level with rotating table will measure the intensity of each direction at this surface. When rotating with vertical axis, the detector will measure the intensity at the vertical surface. The vertical and horizontal axis can be rotated continuously at ±180° or 0~360°. According to the measurement requirements, the system can be operated in C-γ coordinates. When getting intensity distribution data, computer will calculate other photometric parameters automatically.
-
product
Light Source
pE-300ultra
CoolLED's pE-300ultrais a fluorescence microscopy light source which offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. Users have access to both microsecond switching via multiple TTL inputs and the ability to mount inline excitation filters. This, when paired with today's high performance multi band filter sets, facilitates imaging traditionally done via a white light source and a filter wheel, with all the benefits of LED.
-
product
Light Source Series
*High output power*Stable and reliable*CW or MOD output*MOD frequency: 270Hz/1KHz/2KHz*SMT, lightweight*Power supply by battery
-
product
Lighting Maintenance
Lumen maintenance is the most useful gauge to determine the lifetime or useful light output rating of an LED light source.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
-
product
Safety Light Grids
*Type 4 (IEC 61496) safety light curtains at Type 2 pricing*Reliable protection of hazardous areas*Industry standard M12 connection for simple wiring*Versions for the use in high pressure cleaning applications*Versions with active /passive system
-
product
Light Source
UVM-SP-JW
Readouts of UV intensity and cumulative luminescence count are prompted either on the front panel or via the externally connected remote signal control. The UV intensity detection segment is intended to measure a specific intensity of light signals, while the cumulative luminescence count is designed to tally a cumulative count on all UV intensities measured, in conjunction with real-time calibration.
-
product
Lamp-Based Calibration Light Sources
Lamp-based calibration light sources from Gamma Scientific are used for optical calibration of light measurement instruments including spectroradiometers, photometers and radiometers. All of our calibration light sources meet rigid quality standards for use in the most challenging testing environments. A wide range of light sources is available to serve as precision standards of radiant flux and white-light standards of spectral irradiance or luminance.
-
product
Light Sources
There are many low cost artificial light sources used for illumination or for industrial applications: tungsten or halogen bulbs, fluorescent lamps, LED lamps etc. Some of these sources have regulated intensity of emitted light. However, there very few calibrated light sources of precisely known parameters. A light source can be considered as calibrated when its user can precisely regulate its photometric/radiometric parameters like luminance (or illuminance), radiance (or irradiance) at defined spectrum of interest. Such light sources are needed in many applications among them, in systems for testing night vision devices, VIS-NIR cameras and SWIR imagers. Inframet offers a series of calibrated light sources that can be divides into three groups:
-
product
Military Aircraft Lighting
Oxley continues to provide the benchmark in LED lighting for military fixed wing and rotary aircraft. Solutions include external lighting systems, internal cockpit/cabin lighting, and the widest range of positional, landing and taxi lights. Both visible and covert solutions are available for day and night operations; many lights in the range provide dual mode capability. Oxley has experience in designing and manufacturing highly specialized solutions such as complex air refueling lighting systems.
-
product
Optical Light Source
Shenzhen Sharingtek Communication Co., LTD
Is used to emit electromagnetic radiation in order to perform a specific task, whether detecting faults, breaks and microbends, characterizing link-loss or certifying LAN/WANs.
-
product
Helicopter Emergency Egress Lighting
HEEL
Helicopter Emergency Egress Lighting (HEEL) system provides an independent battery operated lighting system that marks crew and passenger emergency exits onboard a helicopter. In addition, it visually identifies exits under all cabin conditions including smoke or water filled, capsized and completely submerged thus providing the passenger with an unambiguous definition of the location of the nearest emergency exit.
-
product
LED Uniform Light Sources
Integrating sphere light source with LED illuminants (white, RGB-colored, NIR). Options available like variable output control and monitor detectors. We are experts in providing customer specific systems. Please contact us for all possible solutions and finding your perfect solutions. E.g. for EMVA 1288 Standard.
-
-
product
Laser Interferometers
Measurements of the length displacement or yawing and pitching, measurements of rotation angles, measurements of overshoots during vibrations or when stopped and of uneven speed, etc. can be handled. Length measuring instruments can be used for a variety of purposes, including precise inspection of heavy duty equipment.
-
product
C/L-Band ASE Light Source
ASE7000
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai ASE7000 series is C/L-Band ASE light source with featured with high stability and high output. It is mainly applied for testing of C/L-Band optical components and optical communication equipments as well as Fiber Optical Sensor etc. Huatai ASE7000 has three types of exterior structure, suitable for different customer’ requirements.
-
product
Light Source
LS-HA
provides the stable and smooth wide-band spectral output. It’s proper for most visible to near infrared range measurement. This light source is also designed to be used in the standard measurement package. It ‘s a simple and quick measurement platform.
-
product
4-CH Lighting Control Module
AX92353
*4-CH independent constant current LED drivers (up to 1 A)*Supports strobe and trigger mode*Intensity control by software*Supports duration and delay time for LED output
-
product
Light Meters
An instrument for measuring the intensity of light, used chiefly to show the correct exposure when taking a photograph.
-
product
Handheld Optical Light Source
JW3109
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3109 optical light source can provide 1 to 4 output wavelengths to meet specific requirements, including the 650nm red source and the 1310/1550nm wavelengths for single mode fiber or the 850/1300nm wavelengths for multimode fiber, as well as other wavelengths according to customer needs. Together with the JW3208 optical power meter, it is a perfect solution for the fiber optic network characterization.
-
product
Digital Light Monitor
LMC-20
The LMC-20 functions not only as a light monitor for coating thickness, but also allows control of multi layer/multi material coating processes. Up to 2000 individual layers in a coating are possible, by using 40 program banks of 50 layers each. The characteristics of up to 99 different coating materials can be input as well. Final thickness can be calculated to 1% of a quarter wave.
-
product
Tunable Deuterium and Tungsten-Halogen Light Sources
Deuterium and Tungsten-Halogen tunable light sources are convenient and affordable solutions for your laboratory experiments. Their optimized optical design, delivers efficient and power stabilized broadband optical power with variable aperture and selectable bandwidth with wavelength ranging from 180 nm up to 2 micron depending on your choice of the lamp.
