Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
Categories
-
product
Digital Coating Thickness Gauges
The Elcometer range of digital coating thickness gauges has been specifically designed to provide highly accurate, reliable and repeatable coating thickness measurements on almost any substrate, whether ferrous or non-ferrous. Dry Film Thickness can be measured on either magnetic steel surfaces or non-magnetic metal surfaces such as stainless steel or aluminium using a digital coating thickness gauge. The principle of electromagnetic induction is used for non-magnetic coatings on magnetic substrates such as steel. The eddy current principle is used for non-conductive coatings on non-ferrous metals substrates.
-
product
Wet Sponge Pinhole Detection
Wet Sponge Technique: A low voltage is applied to a moist sponge. When the sponge moves over a coating flaw, liquid penetrates to the substrate and completes an electrical circuit, setting off the alarm. The wet sponge technique is suitable for measuring insulating coatings less than 500μm (20mils) on conductive substrates, and is ideal for powder coatings and other coatings where the user does not wish to damage the coating.
-
product
Long Edge Wet Film Combs (Stainless Steel)
3238
Each comb has 24 measurement steps (teeth) providing a more accurate wet film thickness value.
-
product
Density Cup
1800
The Elcometer 1800 Density Cup is a stainless steel precision cup for determining the specific gravity or density of paints and similar products.
-
product
Surface Contamination Kit
138/2
The Elcometer 138/2 Surface Contamination Kit provides the user with a means for testing invisible surface contaminants including:pHchloride ionsironsalts
-
product
BS Viscosity Flow Cups
2354
The Elcometer 2354 BS Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
product
Shore Durometer
3120
The Elcometer 3120 range of Shore A and Shore D Durometers is widely used to test the hardness of soft materials.
-
product
FORD/ASTM Viscosity Cups
2351
The Elcometer 2351 FORD/ASTM Viscosity Flow Cups are very easy to use instruments made of anodized aluminium with a stainless steel orifice, for measuring the consistency of paints, varnishes and similar products.
-
product
Calibration
Formal quality systems, such as those described in ISO 9000, require gauges to be properly controlled, logged and in calibration. Increasingly, users are specifying that the readings taken by gauges are traceable to National Standards. There are three types of coating thickness standards available from Elcometer: calibration foils, coated standards and zero test plates.
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Pull Off Adhesion Tester
106
Applications for the Elcometer 106 Adhesion Test include paint or plasma spray on bridge decking, coatings on steel, aluminium, concrete etc.Supplied in a carry case - ideal for site testsHand operated - no need for a power supplyIncludes a cutter for EN13144 and ISO 4624 tests
-
product
Oven Temperature Profile
Temperature profiling provides an effective method for measuring the actual environmental and product temperature during the cure process - essential for ensuring quality finish and a successful cure of a powder coating.
-
product
Coatings Inspection Division
For over seventy years, Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings industry. Whether you are measuring surface profile, surface cleanliness, dry film thickness, porosity, adhesion or gloss; or testing the abrasion, scratch resistance or elasticity of a coating - Elcometer's extensive and versatile range of equipment provides the complete solution to your coatings inspection requirements, whatever and wherever they might be.
-
product
Sclerometer Hardness Tester
3092
The Elcometer 3092 Sclerometer Hardness Tester measures the hardness of a coating by moving a Tungsten Carbide Tip over the coating with a predetermined force.
-
product
Abrasion and Washability Tester
1720
The Elcometer 1720 Abrasion and Washability Tester is robust, reliable and extremely versatile and is designed for testing the washability, brushability and resistance of a wide range of materials.
