Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +44 (0)161 371 6000
- +44 (0)161 371 6010
- Edge Lane
Manchester, England M43 6BU
United Kingdom of Great Britain and Northern Ireland
-
Product
Protective Coating Inspection Kit 3
-
Measurement parameters include:Surface profileSurface temperatureClimatic conditionsCoating thicknessAdhesion
-
Product
Elcometer MarSurf PS10 Surface Roughness Tester
7062
-
In protective coating applications there is a requirement to measure surface roughness. With 31 surface parameter settings available the Elcometer 7062 surface roughness tester can display all parameters that comply to National & International Standards.These values include peak-to-valley profile measurement in combination with an assessment of the frequency of peaks within the sample area.The Elcometer 7062 surface roughess tester is a light weight and portable measuring solution for the range of surface roughness measurements required for compliance to International Standards.The unit is also suitable for assessing surface roughness conditions in a wide range of general industrial applications; particularly where the sample is too large to bring to the laboratory.
-
Product
Dewpoint Meter
319
-
A hand-held dewpoint meter with both manual and automatic data logging in one gaugeIntegrated magnets allow the dew point gauge to be attached to the substrate during remote loggingStores 25,000 records in up to 999 batchesDustproof and waterproof gauge with fully sealed sensors (equivalent to IP66)Gauges can be recertified at Elcometer Authorised Service CentresRobust temperature sensorsEasy to use, intuitive menu structureMeasure and record climatic parameters:Relative humidityAir temperatureSurface temperatureDewpoint temperatureTΔ (the difference between surface temperature and dewpoint)Dry Bulb temperatureWet Bulb temperatureExternal temperature correction (K-type)Specific HumidityVisual and audible indication of user defined limits for any or all parametersUSB and Bluetooth® data output to ElcoMaster® software
-
Product
Metal Box Locator
-
The Elcometer Metal Detection range includes Valve Box Locators that are rugged and simple to use making them the ideal choice for all location work in all types of terrain.
-
Product
Concrete Moisture Meter
7410
-
The electrodes transmit parallel low frequency signals, calibrated to give average moisture content by comparing the change in impedance between damp and acceptably dry concrete.Calibrated ready for use on concreteInstant readings on a clear, easy to read scaleFully portable, battery operated and non-destructive
-
Product
Automotive Paint Meter
311
-
The Elcometer 311 Automotive Paint Meter allows the user to quickly identify vehicle’s damage not reported in public or commercial condition reports including:hidden reworkvehicle impact damagevehicle resprayfilled body panels
-
Product
Elcometer Bresle Patches
135B
-
Elcometer 135B Original Bresle Patches are used to determine surface chloride contamination and are self-adhesive rubber film patches with a sealed compartment for sampling soluble impurities from steel surfaces with a suitable solvent.
-
Product
High Voltage Porosity Detection
-
High Voltage Technique: The high voltage, or porosity technique, can be used to test coatings up to 25mm (1”) thick and is ideal for inspecting pipelines and other protective coatings. Coatings on concrete can also be tested using this method.
-
Product
High Precision Grindometer (Single Channel)
2050
-
This Elcometer 2050 High Precision Grindometer is a single channel precision gauge used to determine particle size and fineness of grind for many materials including paints, pigments, inks, coatings, chocolates and other similar products.
-
Product
Coating Thickness Gauge - Integral
Elcometer 456
-
Whether you are measuring on smooth, rough, thin or curved surfaces, the Elcometer 456 Dry Film Thickness Gauge produces accurate, temperature stable measurements thanks to its ±1% thickness measurement capability and increased reading resolution.
-
Product
Paint & Powder Coating Thickness Gauge
415
-
The new Elcometer 415 Industrial Paint & Powder Thickness Gauge provides simple, fast and accurate coating thickness measurements on smooth and thin industrial paint and powder coatings.
-
Product
Washability & Abrasion
-
Improved mechanical resistance to wear is a key requirement of a wide range of products. From coatings to clothing, leather to upholstery, keypads to plastic toys, a product’s ability to resist wear is an important characteristic. There are testing methods relating to the ‘abrasion by friction’ concept. Others are based on the projection of abrasive particles on to the test specimen. These techniques provide valuable information about materials and processes.
-
Product
Concrete Inspection
-
Concrete structures are normally constructed using steel reinforcement and Elcometer offers Concrete Covermeters and Rebar Locators to either measure the depth of concrete over the rebar or simply to detect the rebar under the surface. Half-cell versions of the Covermeter can be used to assess the probability that corrosion is taking place on the rebar. Test Hammers are used to assess the surface hardness of cured concrete and Elcometer offers several moisture meters that can be used to determine if the structure is sufficiently dry for coating.
-
Product
Wet Film & Powder Thickness
-
When applying a liquid coating, by measuring the uncured film thickness, it is possible to determine the eventual dry film thickness. Applying too much coating wastes time and materials. It can also affect the performance and finish of the product. Too much wet film can cause the coating to crack as it cures; too little coating increases the risk that the substrate will not be sufficiently protected, leading to rust spots.
-
Product
DIN Viscosity Dip Cups - Frikmar
2434
-
Thanks to its handle, the Elcometer Frikmar Viscosity Dip Cup is very easy to use to perform viscosity checks on site or during the manufacturing process.
