Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
-
Product
Manual Clemen Unit
Elcometer 3000
-
The Elcometer 3000 Manual Clemen Unit is a robust and simple to use instrument for evaluating the resistance to scratching of a coated surface.
-
Product
Digital Pocket Thermometer
212
-
The probe conveniently folds back into the side of the instrument, preventing damage when not in use.Liquid or surface probe options availableUser switchable between °C and °FResolution can be set to 0.1°C (0.1°F) or 1°C (1°F)
-
Product
Scrub Test Panels
4695
-
In a typical scrub test, the coating is applied to the Leneta Scrub Test Panel at a specified film thickness, allowed to dry and then subjected to scrubbing with a straight-line scrub tester.
-
Product
Pull-Off Adhesion Tester
506
-
The Elcometer 506 are lightweight, portable and easy-to-use adhesion testers available in analogue or digital gauges and are suitable for measuring the pull-off adhesion of coatings up to 50MPa (7250psi) either on-site, or in the laboratory.
-
Product
Dewpoint Calculator
114
-
The Elcometer 114 Dewpoint Calculator provides accurate values of Dewpoint and Relative Humidity (RH) from the wet and dry bulb temperatures measured by a Whirling or Sling Hygrometer.
-
Product
Elcometer MarSurf PS10 Surface Roughness Tester
7062
-
In protective coating applications there is a requirement to measure surface roughness. With 31 surface parameter settings available the Elcometer 7062 surface roughness tester can display all parameters that comply to National & International Standards.These values include peak-to-valley profile measurement in combination with an assessment of the frequency of peaks within the sample area.The Elcometer 7062 surface roughess tester is a light weight and portable measuring solution for the range of surface roughness measurements required for compliance to International Standards.The unit is also suitable for assessing surface roughness conditions in a wide range of general industrial applications; particularly where the sample is too large to bring to the laboratory.
-
Product
Pfund Thickness Gauge
3233
-
Available in aluminium or stainless steel this instrument consists of two concentric cylinders, one sliding inside the other. A spherical glass lens, which has engraved measurements, is fitted to the end of the central cylinder and when pressed into the wet film, leaves a circular trace.The diameter of the mark on the lens is measured and, using the supplied conversion table, the thickness of the coating can be easily assessed.Ideal for measuring the thickness of wet translucent products such as varnishes, oils etc.Measurement range of 2.25 - 360μm (0.09 - 14.17mils)
-
Product
Powder Coating Inspection Kit
-
Elcometer has produced this kit to enable the inspection of powder coatings on all surfaces. For a smooth surface, the digital Elcometer 415 Paint and Powder Gauge may be used but for more demanding, uneven surfaces, the Elcometer 1542 Cross Hatch Adhesion Tester is included.
-
Product
Plastic Wet Film Combs
154
-
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
Product
Motorised Clemen Unit
3000
-
The Elcometer 3000 Motorised Clemen Unit is a robust and accurate instrument for evaluating the resistance to scratching of a coated surface. The sample can be metal, wood, glass, plastic or other hard materials.
-
Product
CoverMaster™ Software
-
Elcometer's CoverMaster™ software will manage your data efficiently and effectively. Data is transferred quickly into the CoverMaster™ software data management system via RS232 connection. Both Covermeter and half-cell readings can be stored together with associated photographs, Word documents, Excel spreadsheets and other files.
-
Product
Glossmeter
480
-
Quickly and accurately measure and record Gloss, % Reflectance & Haze measurements on a wide range of materials, including paint, plastic, ceramic or metal with the Elcometer 480 Glossmeter.
-
Product
Surface Profile
-
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
Product
Protective Coating Inspection
Kit 5
-
A more comprehensive kit than kits 1-4, the Elcometer Protective Coatings Inspection Kit 5 expands the range of instruments available to the protective coatings inspector.
-
Product
Climate, Dewpoint & Relative Humidity
-
Monitoring climatic conditions, such as temperature, relative humidity, dewpoint and moisture, is often vital to the successful application of a coating and are critical to the resulting quality and performance of the coated product.
