Elcometer Limited
For more than seventy years Elcometer has been a world leader in the design, manufacture and supply of inspection equipment to the coatings, concrete and NDT industry.
- +1 248 650 0500
- +1 248 650 0501
- sales@elcometer.com
- 6900 MIller Drive
Warren, Michigan 48092
United States of America
-
Product
Daniel Flow Gauge
2290
-
The Elcometer 2290 Daniel Flow Gauge is a simple gauge used to conduct flow measurement of thick or paste-like materials, such as paints or printing inks.
-
Product
Fineness of Grind Gauges
2020
-
The Elcometer 2020 Fineness of Grind Gauges is used to determine the particle size and fineness of grind of many materials including paints, pigments, inks, coatings, chocolates and other similar products.
-
Product
High Voltage Porosity Detection
-
High Voltage Technique: The high voltage, or porosity technique, can be used to test coatings up to 25mm (1”) thick and is ideal for inspecting pipelines and other protective coatings. Coatings on concrete can also be tested using this method.
-
Product
Cupping Tester
1620
-
This robust and user-friendly Elcometer 1620 Cupping Tester is used for assessing the cupping ability of coatings applied to metal sheets up to 1.2mm (0.05”) thick.
-
Product
Pencil Hardness Tester
3080
-
The set of Elcometer 3080 Hardness Testing Pencils provide a simple but effective technique to evaluate the hardness of many coatings.
-
Product
Thickness Gauge
124
-
The Elcometer 124 Thickness Gauge is used to measure the peak-to-valley height of a surface profile moulded in the Elcometer 122 Testex® Replica Tape.
-
Product
Surface Comparators & Magnifier
127
-
Designed for use with the Elcometer 127 illuminated magnifier, each surface comparator has a hole in the centre allowing for clear visual comparisons to be made.
-
Product
Lory Viscosity Cup
2215
-
The Elcometer 2215 Lory Viscosity Cup is a conventional cylindrical cup with a needle fixed into the bottom for quick measurements on-site or during production.
-
Product
Setaflash ‘Series 3’ Open Cup Tester
6910/2
-
The Elcometer 6910/2 Setaflash 'Series 3' Open Cup Tester offers the fastest and most accurate flash point instrument at a cost effective price.
-
Product
Cylindrical Mandrel Bend Tester
1506
-
The Elcometer 1506 Cylindrical Mandrel Bend Tester is robust and used to determine the elasticity, adhesion and elongation properties of cured coatings on sheet metal.
-
Product
Blast Nozzle Gauge
103
-
The Elcometer 103 Blast Nozzle Gauge measures the orifice size of an abrasive blasting nozzle. This gauge is used to determine the nozzle orifice wear which leads to low nozzle pressure and decreased efficiency in its performance. Nozzle orifice wear results in decreased productivity and increased abrasive media consumption.
-
Product
Paint & Powder Coating Thickness Gauge
415
-
The new Elcometer 415 Industrial Paint & Powder Thickness Gauge provides simple, fast and accurate coating thickness measurements on smooth and thin industrial paint and powder coatings.
-
Product
Moisture Measurement
-
Moisture: The presence of moisture within a material will result in poor adhesion, premature coating failure and poor appearance. For example, applying a powder coating to a damp wooden panel will cause steam to be created when the panel passes through the curing oven, thus causing damage to the coating. It is not sufficient to simply ensure that the surface is dry by touch. The surface of the substrate is often the driest point due to evaporation. It is important to establish the moisture content within the substrate itself. The moisture measurement can either be taken using a Pin moisture meter or Pinless (Contact-Type) moisture meter.
-
Product
pH Tester
148
-
The Elcometer 148 sensor has automatic temperature compensation, ensuring like-for-like measurements can be taken for meaningful comparison of the results.Simultaneously displays pH and temperatureMeasurement hold / freeze functionRecord maximum and minimum readings over a series of tests°C / °F user switchableWaterproof to IP57 and floats on waterAuto power off
-
Product
ElcoMaster Oven Profiling Software
-
*Oven Logger set up & programming*Paint/Powder parameter library*Product probe maps*Fully customisable inspection templates*Selectable probe/channel traces*Statistical analysis by probe/channel*Max, Min, standard deviation, coefficient of variation*Temperature profile, cure progress, histogram & individual cure value graphs against product*Time at temperature, time of peak difference*Time above maximum absolute & minimum cross link temperatures*Fully customisable inspection reports*Combined reports - coating thickness, gloss, adhesion, profile, climate, surface cleanliness*Report generator wizard & PDF generator*Email or export data*Import photo’s, data sheets, critical data, inspection notes, etc & include on inspection reports*Cloud computing - allows for cross site collaboration, including internal text messaging tool*Overlay temperature profiles, review and compare multiple oven profiles over time*Use additional data loggers for multiple channels or run overlays
