Showing results: 8866 - 8880 of 14424 items found.
-
8005 IN -
Standard Electric Works Co., Ltd
● Microprocessor controlled.● Four insulation test voltages (DC) : 50V, 100V, 250V, 500V● The maximum insulation measurement range is 200G ohm @500V.● Large LCD (78 × 67mm)● Auto-ranging.● Bar-graph indication.● Backlight function.● REL(Auto-null) function.● Auto AC/DC voltmeter.● Capacitor test.● Auto-test stop & smart hold.● Supplied with high quality test leads.● Safety standard : EN 61010-1 CAT III
-
HL-200 -
Neutronics Manufacturing Co.
Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 200 is a direct reading tester, and uses a test current of 200A DC, resulting in true value and accurate measurements. Model HL- 200 adopts digital circuit technique and is used for measuring contact resistance of switch control equipment at test current of 200A DC. The measurements are accurate as the test is highly stable. HL- 200 is a new, fully automatic micro controlled tester that measures contact resistance at 200A DC with built in printer.
-
GX5295 -
Marvin Test Solutions, Inc.
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Polaris Networks
LBS Tester provides an end-to-end test bed for Mobile Network Operators and Network Equipment Manufacturers, to verify the accurate implementation of the location services network. The LBS Tester tests that the Location Server (System Under Test) is correctly executing the positioning procedures over the control plane and/or user plane of that network. To test normal signaling, or failure scenarios, over the LTE User Plane as the number of SETs (SUPL Enabled Terminals) simulated by the LBS Tester increases, the Location Server must execute LPP (Location Positioning Protocol) procedures over SUPL (Secure User Plane Protocol) with success, or without, respectively.
-
XLR Sniffer/Sender -
Sound Tools
Designed by Rat Sound to deal with the "real world" of pro audio, the SoundTools Sniffer/Senders are the perfect tools for live environments. Test snake lines and cables when the ends are at a distance and avoid running extra cables just to test. Utilizing phantom power the Sniffer end can quickly test snake lines in minutes. The aluminum barrels eliminates the problem many testers face with solder joints failures and the unit will never rust. 3 simple LED’s will instantly diagnosis your cable as it tests for every possible shot, open, or cross wire in XLR cables. If the LED’s read all green you cable will work!
-
MIT2500 -
Megger Group Ltd.
The MIT2500 insulation and continuity tester has been designed for motor and cable testing, specialist applications and electrical testing applications, where operation voltages exceed 1000 V and higher insulation test voltages are needed. The MIT2500 offers both fixed range voltages of 50 V, 100V, 250 V, 500 V, 1000 V and 2500 V, as well as a variable range that allows any voltage between 50 V and 2500 V to be "dialled in". This is supported by the new test voltage feedback control, which maintains the output test voltage to within 2% of the selected range, even when under test.
-
Mostrak-2 -
ipTest Limited
M2 test system has multiple test generators which cover static and dynamic test procedures. It is our first truly modular tester which allows for the system to be upgraded and expanded when needed. M2 are designed to get the tester as close as possible to the handler interface and operator at the highest possible speeds. M2 is capable of HV (3 kV) and LV (600A) testing and has dynamic switching capabilities up to 1200V. MOSTRAK systems can test the following device types: MOSFET, IGBT, Bipolar transistor, Diode - rectifiers, Thyristor (SCR) - Triac, Linear voltage regulator (VReg), Transient voltage suppressor (TVS).
-
GX5295 -
Terotest Systems Ltd.
The GX5295 offers outstanding digital test capabilities and channel density in a compact 3U PXI form factor. Offering both performance digital and analog test capabilities, the GX5295 provides a cost-effective, tester per pin architecture - making this card the ideal choice for high throughput, mixed-signal component test applications. Each digital channel can be individually programmed for a drive hi, drive lo, sense hi, sense lo, and load value (with commutation voltage level). In addition, each channel offers a parametric measurement unit (PMU) providing users with the capability to perform parallel DC measurements on the DUT (device under test).
-
Model 4300R -
Aplab Limited
Aplab Precision LCR Meter Model 4300R is a new generation of impedance test equipment with high accuracy, wide measurement range and six digits resolution. Being featured with test frequency up to 300kHz, test voltage of 5mV ~ 2V, built-in -5V ~ 5V DC bias and -10V~10V DC voltage source output, it can meet all requirements for measuring components and materials and provide guarantees for production line quality assurance, incoming inspection and laboratory precision measurements. The Handler, RS232C and GPIB interfaces as well as improved command system provided by the instrument make it easier to build the test system.
-
ET System Electronic GmbH
Thanks to our many years of experience and our extensive product range of system components, laboratory devices and modular control and measuring systems, we can also offer you complex system solutions. We develop user-oriented software solutions quickly, and our design team is able to quickly and efficiently adapt standard system components to your special requirements. We can also develop complete parts of a test system according to your requirements and integrate them into the structure of the system components. In this way, systems such as function test systems, handling systems, safety test systems or battery test systems can be configured cost-effectively.
-
M41h -
Teledyne LeCroy quantumdata
The Teledyne LeCroy quantumdata M41h 48G Video Analyzer/Generator for HDMI 8K Testing is a compact versatile test instrument offering entry level functional testing that can be extended through software licenses to a full compliance tester with sophisticated analysis and diagnostic capabilities. The M41h enables design and test engineers to validate their products for interoperability and reliability for the HDMI 2.1 video interface. The M41h is a flexible test instrument that can be upgraded from a functional tester for sources and sinks to a sophisticated analyzer and, if desired, can test full standards compliance, enabling developers to pre-test or self-test independently, reducing delays and costs during the product development cycle.
-
UI2002C -
Lisun Electronics Inc.
UI2002C is designed according to the latest update in IEC 61347-2-3 about the test requirements for local rectifying effects on tubes. It imitates the condition when tube is under local rectifying status and tests the abnormal protection function of ballast by adopting fluorescent lamp asymmetry pulse test method with 3 windows for displaying rectified voltage, rectified current, and rectified power. It is easy for operation and with high test accuracy. • Measure lamp voltage, lamp current , average and total power of lamp. • Lamp voltage range: 10~300V • Lamp current range: 10mA~1.0A • Lamp power range: 0.5~300W • Tolerance is 5%
-
2801 IN -
Standard Electric Works Co., Ltd
● Microprocessor-controlled with advanced safety features.● Three test voltages : 250 / 500 / 1000V.● Displays and sound warning if external voltage present.● Ener-Save™ feature to extend battery life.● Continuous battery monitoring.● Auto ranging / auto-null / auto-off.● Insulation tested at 1mA.● Built-in carry case, test leads in separate pouch.● Real-time barg-raph display of test voltage and voltage decay during discharge.● Audible and visual message displayed if external voltage is present.● Large LCD.● Display can be customized for special orders.● Continuity buzzer.● Show test time duration (up to 99.9s) for easy comparison.● BS 16 edition.
-
PCCextend 125 -
Sycard Technology
The PCCextend 125 is a flexible extender card designed to provide easy access to a CardBus PC Card for debug or test. Designed with the same low noise characteristics of our PCCextend 140, the PCCextend 125 takes this design a step further by connecting the host and card via ribbon cables. The flexible extender consists of two PC boards—the host interface board and the card interface board. The host interface board is inserted into the host's CardBus slot.
-
PDMT08 -
Pyle Audio Inc.
Double-Molded Plastic HousingHigh-Contrast LCD DisplayCATIII RatedVoltage DC: Max Range 600 V, Accuracy: +/- 0.5%Voltage AC: Max Range 600 V, Accuracy: +/- 1.2%Current DC: Max Range 10 A, Accuracy: +/- 2.5%Resistance: 2 M, Accuracy: 0.8%Diode CheckContinuity TestAccessories Included: Test Leads, 9V BatteryDimensions: 5.91' H x 2.76' W x 1.89' DWeight: 8.99 oz.Sold as : Unit
