Showing results: 1021 - 1035 of 1830 items found.
-
MSXB 042 -
Microstar Laboratories, Inc.
The MSXB 042 Analog Termination Board allows quick and secure connection of discrete wires to the iDSC 1816 Board. MSXB 042 includes locations to install voltage divider resistors and 0-20mA termination resistors, as well as a Cold Junction Compensation (CJC) circuit for thermocouple applications.
-
ODS Series -
F&K Physiktechnik GmbH
The optical displacement measurement systems of the ODS series are specially designed for measuring the ultrasonic vibration displacement at bond tools of wire & flip-chip die bonders. The systems are highly accurate and very easy to use. That makes it the perfect tool for displacement based calibration of ultrasonic bond machines.
-
Spot Sensor -
Advanced Thermal Solutions, Inc.
The SP 1000-20R1 is a single-sensor probe designed for measuring the surface temperature of solids. Its small size allows for the exact positioning of the sensor at the desired spot. The size of the sensor eliminates any conductive heat transfer that may occur through the lead wire, enhancing measurement accuracy.
-
SERIES 33 -
Test Connections Inc.
ElectricalMAXIMUM CURRENT:3 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,20 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24Kt gold plated over nickelBARREL: Nickel silver with preciousmetal clad ID.SPRING: Music wire, silver plated
-
KT-98 -
KILTER ELECTRONIC CO.,LTD
3 3/4 digits, Max. reading 3999. It can be used for the measurement of cell phone,USP and other types of batteries. Measuring resistance of the battery and the engine temperature. Automobile Meter with Tacho, Dwell and Battery Impedance Test. 4 wire test mode, with all multimeter functions
-
MPK-253 -
MEGABRAS srl
The MPK-253 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10 A.
-
80609000 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
80609007 -
6TL Engineering
The single ended active probe helps to carry weak HF signals far away with the minimum disturbance of the original source. The module accepts discrete wiring or direct spring loaded test probe solder. In any case, the input signal wires might be as short as possible.
-
Beacon -
DG Technologies
6 High Speed CAN/CAN FD Channels 1 Single Wire CAN Channel 1 Fault Tolerant CAN Channel 2 Local Interconnect Network (LIN) Channel 1 GB Ethernet Connectivity Wi-Fi Enabled USB Connectivity On-board Media Storage Can be powered by USB, the vehicle, or 12V Power Adapter (included)
-
Shenzhen Wiitek Technology Co.,Ltd
In both active and passive variants, DACs feature copper wire that connects two fixed transceiver modules on either end. AOCs, on the other hand, use multimode fiber to connect permanently attached transceivers. Both function as alternatives to purchasing individual modules and cables separately.
-
Extech 850189 -
Extech Instruments Corporation
The Extech 850189 is an Air Temperature RTD Probe capable of air temperature measurements from -40°C to 500°C (-40°F to 932°F). Features a 4 wire, Pt-100 Ohm RTD probe with a 4 pin DIN plug and a six month warranty.
-
MDCOPT -
Matco Tools
The Coil-on-Plug Spark Tester provides an easy way to check ignition systems with coil-on plugs (COP). Quickest way to test for no-start conditions. Inductive test cannot be performed because there are no plug wires. Applications include Ford, Chrysler, Mitsubishi, Nissan and many more.
-
TH458 -
Matco Tools
For ignition systems with coil-on plugs, including Ford, Chrysler, Chrysler imports, Mitsubishi, Nissan, and more. Since coil-on plug ignitions do not have plug wires, inductive test equipment cannot be used. Spark tester tests for no-start conditions and measures coil output.
-
RandHDPE HDPE Family -
Test Electronics
HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
16820-100 -
M. C. Miller Company
The Model PS1 under tank probe is designed to be used in conjunction with customer-supplied ¾” National Pipe Thread (NPT) PVC piping and the product has a ¾” (NPT) threaded end that accepts a standard coupling. Any number of pipe pieces can be combined via couplings to provide the required probe insertion length under a tank. The probe can be combined with any standard reference electrode with a ¼ x 20 threaded fitting, including the RE-5, RE-5C and RE-7 portable reference electrodes. Reference electrodes are sold separately. The sealed cable to be fed through a customer-supplied PVC pipe comprises #16 AWG wire with red colored PVC insulation and the wire length can be selected via the radio buttons in the field below.