Showing results: 571 - 585 of 1831 items found.
-
40-970-025-1m-MF -
Pickering Interfaces Ltd.
The 25-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. male Screwlocks are provided to secure the connectors to their associated products.
-
A020GMR-T-1B100 -
Pickering Interfaces Ltd.
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product.
-
A026HF4-T-0A200 -
Pickering Interfaces Ltd.
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks.
-
A020GMR-T-1B200 -
Pickering Interfaces Ltd.
The 16A 20-Pin GMCT cable assembly is constructed from 19/0.41 (14AWG) Copper Wire with PFA 500V insulation. Screwlocks are provided to secure the connector to associated product.
-
CX-DWC -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884-1 Uses: It is used to evaluate the impact resistance of electrical accessories under low temperature conditions, and also to evaluate the low temperature impact resistance of wire and cable.
-
Earth Clamp -
Metrel d.d.
Digital measuring instrument for measurement on earthing and lightning protection systems. Specific earth resistance (soil resistance) measurement with a 4 wire method up to 30m deep.
-
DAQM902A -
Keysight Technologies
DAQM902A 16 Channel Multiplexer (2/4-wire) Module. Reed relays with high voltage switching of up to 300 V and scan speed up to 250 ch/s.
-
XM Bond HR -
Viscom AG
Viscom AG offers the new XM Bond HR camera module for dependable inspection of wire bonds. Its characteristics include a 21 mm x 21 mm field of view size and exceptionally fine detail resolution. It is ideally suited for the most precise inspection of thin wires in the production line. With the new XM Bond HR camera module, Viscom advances the configuration possibilities in wire bond inspection for higher in-line inspection quality. This module is particularly recommended for safety-relevant electronics, where thin wires with diameters of e.g. only 20 µm are installed. Products of this kind find use, among others, in various types of signal processing in the automotive and aerospace sectors. The high-quality optical components and sensor chips with first-class resolution and sensitivity achieve superb image quality and sharp detail resolution. Together with its 21 mm x 21 mm field of view size, the XM Bond HR offers a resolution of 4.5 µm per pixel. A telecentric lens ensures that regardless of the distance to an object, an inspection window has the same image scale; for example, the end points of an inspected thin wire are always located at the same positions in the inspection window. In addition, the telecentric optics also prevent areas on the electronic assembly next to tall components from being hidden.
-
40-200-008 -
Pickering Interfaces Ltd.
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
CB29H -
CAMI Research Inc. (CableEye®)
CAMI Research Inc. (Acton, MA) announces another new board for its CableEye cable and harness testing systems. Populated with four 16-pole screw terminal blocks, the board addresses high voltage (HiPot) testing to 2100Vdc/1200Vac. Of particular interest to the harness testing market, the CB29H is also available as a transition board variant (CB29AH). The CB29H and CB29AH boards are high voltage versions of the CB29 with the high voltage traces running on inner layers to afford additional safety, and protection from contamination. Each contains four 16-pole screw terminal blocks that will accept bare wires from 12- to 30-gauge in size. The metal jaws firmly grip an inserted wire without damaging or distorting the end, and the space between each terminal block may be used as a wire channel to guide wires neatly to the side. For each channel, a pair of holes is provided through which wire ties may be inserted to hold the wire bundles in place.
-
FT6380 -
HIOKI E.E. Corp
The FT6380 measures grounding resistance simply by clamping to multiple-grounded ground wires. No auxiliary grounding rod is needed, and there is no need to disconnect the ground wire from the grounding rod. The compact, low-profile sensor can be used to clamp ground wires with ease, and also provide AC current measurement functionality and can measure currents ranging from leakage current on the order of several mA to load currents of up to 60 A.
-
350 -
Aines Manufacturing Corp.
AINES 350 NFP is a professional noise filter probe to use in a demanding environment. It is designed to make a technician's job easy while tracing a wire from a bunch of wires with electrical interferences. The 350 NFP is the best option for technicians compared to other available products in the market. Combined with the AINES 140 or 240 Tone Sets, the 350 NFP makes a formidable combination to identify a cable pair quickly and conveniently in a normal environment and in locations with electrical interferences as well.
-
ZWH-, ZWN-, & ZWP-Series -
Micro-Measurements
ZWH-, ZWN-, and ZWP-Series strain gages are designed for dynamic and limited static strain measurement at hightemperature.These strain gages are manufactured using a round wire for superior bonding ability and performance. A high-fatigue wire (Option Z) is also available on each of the gages. These gages are supplied with a fiberglassreinforced tape carrier which holds the grid and leads in place during installation and are bonded using ceramic cements or Rokide® flame spray. The shelf-life of thesegages is 9 months.
-
56810 -
Lisle Corp.
Set includes four jumpers to fit the most popular size relays on domestic and import vehicles. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using green four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on. Set comes in blow-molded case for storage.
-
CLM-1000 -
Greenlee Tools
*Measures these AWG wire gages: 18, 16, 14, 12, 10, 8, 6,4, 2 , 1/0, 2/0, 3/0, 4/0*Measures these kcmil wire sizes: 250, 350, 400, 500, 600, 750, 1000*Eight user-programmable settings for other gages*Powered by (6) 1.5V AA batteries*Replacement calibration rods (pair) available as CLM-ROD, UPC 02721*Replacement Kelvin clips (pair) available as CLM-CLIPS, UPC 02722*Feet