Showing results: 1531 - 1545 of 1831 items found.
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
A non-contact voltage tester is the safest way to make sure the power is off without touching any wires. Before you open an electrical box, you should: - cut off power to the outlet at the main electrical panel - confirm you turned off the right circuit This is where the non-contact voltage tester comes in handy.
-
1942 -
Peaceful Thriving Enterprise Co Ltd
*With UKCA Approval.*Test for 230VAC circuits.*Neon indicators.*Detect faulty wiring status in 3 wire receptacle.*Various combinations of 3 neon indicators tell if wiring is OK or 6 possible faulty conditions.*Power Plug type: UK 13A socket-outlet*Measurement Category: CAT II / 1W*Frequency: 50Hz
-
cPCI/VME/VME64x -
Kontron
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
PeakTech Prüf- und Messtechnik GmbH
The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs. The power cord with an Euro plug is firmly connected to the power supply unit, whereby the device is switched off and on via a rear power switch. This handy power supply fits on every work bench and can be used universally in the hobby area, service or training.
-
XCBS-DL -
Green Switch Innovations
The XCBS-DL is permanently wired into each crossing warning system, and can be configured with either a removable or non-removable bypass key. Simply connect the track connection harness to the designated track connection terminals. To prevent unnecessary operation of the crossing warning system, insert the key and select "bypass", rotate the knife switch to "bypass" and the crossing is disabled. When in the "bypass" position, a Dummy Track Load is connected to the track wire connections in parallel with the rails and the crossing approaches are shorted, preventing unnecessary activation when track equipment is working in the crossing approach circuit. The opening of one track lead may be desired to prevent unnecessary activation with intermittent shunting on the crossing approaches close to the crossing.
-
FEINMETALL GmbH
FEINMETALL offers a wide range of contact probe:ICT / FCT probes, short travel probes, double plunger probes, fine pitch probes, interface probes, wire harness probes, threaded probes, high current probes, switch probes, twist proof probes, push back probes, koaxial probes, radio frequency probes.
-
Verotec Ltd.
Once piece parts have been manufactured, skilled operators can kit or assemble them to the desired level. Our wiring technicians are trained to IPC standards of workmanship and operate within ESD controlled areas. We carry out both solder and crimp wire terminations along with integration of electronic components such as fans, PCBs and power supplies.
-
AXI X# Series -
Nordson Corporation
The X#-platform series is an inline automated X-ray system which covers a wide range of AXI applications. It is a flexible platform with very versatile fields of use depending on the application requirements. The inspectable applications range from component level inspection for wire bonds, large SMT boards, high-power electronic modules up to fully assembled modules.
-
CX-150 -
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Ozone Test chamber is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
-
CMA-100 -
Research Electronics Intl.
CMA-100 Countermeasures Amplifier is a high gain audio amplifier used to detect and identify certain types of surveillance devices attached to building wiring such as telephone wiring, LAN and server systems, AC power, and alarm wire. The CMA-100 Countermeasures Amplifier functions employ a sophisticated automatic gain control circuit that is superior to most audio amplifiers.
-
QES Mechatronic Sdn Bhd
High Speed stroboscopic 2D vision inspection system for die attached and wirebond quality in back-end semiconductor processes. User friendly HMI for easy recipe creation and management. Able to configure with various defect identification module. (Strip Mapping, Inker, Scriber, Pucher, Bristle, Laser wire cutter and Laser clip bonding cutter.)
-
AUTO DIAGNOSTECH LTD
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
DX/HDX Models -
Instron
By building on years of experience, Instron® has kept the best of its static hydraulic technology while infusing the Industrial Series DX/HDX Models with a modern appearance, high-performance electronics, and leading-edge software. Designed for high-capacity tension, compression, bend/flex, and shear testing, these frames are ideal for testing metals, wire, fasteners, concrete, soil, and wood.
-
PR-09SCSIV -
Pansco, Ltd
The Universal Cable Tester is a compact, stand-alone unit which gives technicians an affordable way to test PC, serial ATA, network, telecom, coaxial, USB A/B, mini USB A/B/AB, 1394 Firewire 4/6, and SCSI I, II, III, and V cables for continuity, wiring configuration, opens, shorts, miswiring, and cross-connected wires.
-
105 -
Astro Flight Inc.
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery