-
product
5 kV AC Hipot Testers
Models M100BVS5 & M500BVS5
Now you can perform safe, rapid and efficient hipot testing, ground continuity testing, and total or real current monitoring in one simple operation. The ROD-L Electronics model M100BVS5 and model M500BVS5 hipot testers perform safe and accurate AC hipot and ground continuity testing in compliance with UL, IEC, CSA, VDE, FCC and other electrical equipment testing standards
-
product
Interface for the Multimode, multiprotocol Excalibur 8000 Family of Carrier Boards, Providing a Complete Solution for Developing & Testing MIL-STD-1760 Interfaces
M8K1760Px(S)
The M8K1760Px(S) interface module for the multimode, multiprotocol, Excalibur 8000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M8K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory ...show more -
product
Digital Psophometer
Model 1072
Aplab Psophometer is a portable unit designed for the use of testing telecommunication equipment. It has Psophometric filter, which has the frequency response of the weighing network based on the CCITT recommendations and frequency response characteristics for unweighted measurements. The additional features included in this model are, ‘Recorder out’ available at the rear panel for plotting a response curve, built-in stable calibration signal for calibration check and Lo Battery facility to check the Battery condition.
-
product
RF Helmholtz Coil
The Beehive Electronics 135A RF Helmholtz coil generates a well-controlled, uniform magnetic field. It can be used to calibrate magnetic field probes, such as the Beehive 100 series, or for testing the susceptibility of other devices to magnetic fields. The Helmholtz coil comes supplied with a fixture that makes it easy to calibrate Beehive 100 series probes.
-
product
Gas Meter Gasproof Test Bench
SY8510
Hong Kong Songyang Industrial Ltd.
Test bench and its working principle completely satisfy the requirements of the testing rules of the gas meter. The four work positions can be clamped by the air pump at the same time, the testing pressure and the testing time can be adjusted, its testing efficiency is very high and it is suitable for the batched test of the gas meters.
-
product
Cellular Tester
IQxstream-5G
This high performance, comprehensive non-signaling tester is ideal for both 5G user equipment (UE) & small cell testing across multiple cellular technologies including 2G, 3G, 4G & 5G.
-
product
Voltage Transformer Testing System
KVTS
The Knopp Voltage Transformer Testing System is designed to measure the accuracy of instrument transformers having 120 volt secondaries and up to 14,400 volt primaries (special order for up to 36,000 volt primaries is available). The system includes a control console which contains the control circuitry, ANSI standard burdens, and the Knopp Automatic Transformer Comparator. The Knopp precision and loading transformer set is also included (as pictured) and is connected to the console via a special cable.
-
product
Single-Axis Shaker Vibration Testing
Modular Vibration Control Systems - Scales up to 512 Channels
-
product
OTDR Launch Cable Box, OTDR Dead Zone Eliminator, 1KM-2KM
Shanghai Fibretool Technology Co.,Ltd.
Designed to aid in the testing of fiber optic cable when using an OTDR. TheOTDR Launch Cable Box is used with Optical Time Domain Reflectometers (OTDRs) to help minimize the effects of the OTDRs launch pulse on measurement uncertainty. Available in many different configurations and fiber lengths.
-
product
3U Intel® Celeron® 2000E 2.2GHz Processor-Based PXI Controller
PXI-3930
The ADLINK PXI-3930 PXI embedded controller, based on the Intel® Celeron® 2000E 2.2GHz processor matches superior performance with an unprecedented price point. Specifically conceived for hybrid PXI-based testing systems, the ADLINK PXI-3930 delivers a rugged and stable platform for a wide variety of testing and measurement applications.
-
product
Wiring Tester
WIZE
The testers can be used both in production and maintenance, as WIZE® is suitable for simple wiring tests and complex interconnect tests for full systems. WIZE®’s specifications make it compatible with the standard requirements used for testing in the aeronautics, space, rail and defence sectors or any other industry using wiring.
-
product
Modbus for Windows
Modbus for Windows provides an interactive tool for development, data acquisition, monitoring, and testing of systems employing the MODBUS protocol. This tool provides the interface between the serial or I/P port connected to the MODBUS device and the Window's environment.
-
product
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits
310113002
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits Similar to instrument bracket p/n 310113453, but includes cutout to accommodate air intake on NI PXIe-1088 chassis. Only compatible with slide configurations 28" and longer. Not compatible with cable tray. Not recommended for use with 2+ tier 90 Series systems (905, 9075, etc.).Used to mount testing instrument to slides and also allows test instrument to slide out for maintenance access. Provides strain relief in front area of bracket. Compatible with chassis (see drawing for more information)
-
product
GENEM-C 100G Ethernet/IP Infrastructure Test Application
GENEM-C is a high-capacity network infrastructure testing software application for network equipment manufacturers, data centers, service provider telco cloud and 5G backhaul. It runs on the PROVA-C hardware appliance that is built on BittWare. GENEM-C allows you to verify, monitor and troubleshoot Ethernet/IP network equipment and data center applications to ensure network services can accommodate the demands of your customers. Ideal for QA test, Service Providers migrating to a DevOps model ca...show more -
product
MPI Automated Probe Systems
MPI Advanced Semiconductor Test
MPI’s 200 mm and 300 mm automated probe systems are dedicated and designed to address current and future requirements for all facets of Device Characterization for Modeling and Technology/Process Development, Failure Analysis, Design Verification, IC engineering, Wafer Level Reliability as well as special requirements for MEMS, High Power, RF and mmW device testing.
-
product
PXI High Density MUX BRIC, 48-Chan, 10-Pole
40-570-413
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow tes...show more -
product
Distributed Active Testing & Troubleshooting Software
DVQattest
DVQattest® is a high performance active test and troubleshooting application for proactive management of VoIP/VoLTE, IP Videoconferencing, web, email and other network services and applications. Its compact software test agents run unobtrusively on VMs, routers, servers, PCs, and mobile devices, providing in-depth analysis of voice, video and data performance anywhere in the network at any time.
-
product
PXI Express Gen3 Controller
PXIe-3988
The ADLINK PXIe-3988 PXI Express embedded controller, based on the 9th gen Intel® Xeon® E processor, is specifically designed for hybrid PXI Express-based testing systems, delivering maximum computing power for a wide variety of testing and measurement applications. By utilizing the Intel® Xeon® E-2276ME processor (6 cores, 12 threads) with up to 64 GB of 2666 MHz DDR4 memory, the PXIe-3988 easily performs execution of numerous independent tasks simultaneously in a multi-tasking environment.
-
product
Rapid-Rate Cycling Chambers
TCC
Through simulation of wind volume and wind speed, TCC-150 can minimize specimen temperature variations, enabling more accurate quick temperature change testing. For specimen temperature, the ramp rate is 15°C/min. For air temperature,the ramp rate is 23°C /min (temperature heat-up average).
-
product
PXI 3A Power MUX BRIC, 2-Channel, 48-Pole
40-571-002
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Maple Syrup Refractometer
PA202X-306-307
The eMaple Digital Maple Syrup Refractometer can be used at the tree tap or tank to measure maple sap, for pre-process monitoring of reverse osmosis, in the sugar shack to determine when to draw maple syrup from the boiler, or during maple syrup bottling and testing. The eMaple Refractometer features two scales and measures from 0 to 85 Brix.
-
product
Ergonomic Force Gauges
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges. They are an excellent, low cost solution for tensile or compression testing.
-
product
Auto-ranging Digital Clamp Meter
DCM402
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off, linear bar graph functions and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
product
Generators
Vibration Shock
Software Vibration shock is used for testing specimen resistance to vibration impact. This software is a part of the software complex ZETLAB VIBRO, supplied together with vibration control systems ZET 017-U. The software enables generation of impacts with pre-set parameters and noise presence within a specified frequency range. The software is activated via ZETLAB control panel and VCS menu.
-
product
Compact Digital Multimeter
MT-1705
1/2 digits 1999 counts.0.5% best accuracy.CAT III 600V safety rated.Auto polarity indication.AC True-RMS for accurate measurements.Large backlight LCD display for easy reading.Extra Functions: Continuity with beeper, Diode test, Data hold, Auto power off, Low battery indication, Overload indication, LCD backlight,Frequency and Capacitance are auto rangeIdeal for wide variety of electrical and electronic testing applications.
-
product
Non-functional Testing Services
Good software has both- efficient functionality and excellent performance. While functional testing pays attention to improve the functioning of the software, our non-functional testing solutions aids in enhancing software performance under various conditions. QACraft has helped several enterprises all over the globe to boost performance by evaluating the software when it comes to software and eradicating the lacking factors from it. Carrying out non-functional testing for the software helps in checking the software’s accessibility, scalability, and responsiveness.
-
product
Automotive Fuse Current Probe
FUSE PEEKER
Automotive Diagnostics and Publishing
Automotive Fuse Peeker Current Probe for Testing Injectors, Coils, Solenoids and most components. The FUSE PEEKER Automotive Fuse Current Probe works with your own scope, the Auto Scope 1 or any other type of oscilloscope. It uses magnetic sensor technology, which is accurate and safe for your tool. It can detect small amounts of current as small as 5 milli-amps.
-
product
Temperature & Humidity Testing
DATASYST Engineering & Testing Services, Inc.
DATASYST can simulate both high and low temperature with humidity conditions. Cycle rates are dependent upon individual chamber capabilities and whether or not a unit under test is powered or not. DATASYST provides humidity testing for a range of industry specifications and can work with you on your customized testing requirements.
-
product
Fan Assembly Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable for testing the performance of DC brushed and brushless motor, AC radiator, heater fan assemblies.
-
product
Measurements & Material Testing
MAGNET-PHYSIK Dr. Steingroever GmbH
, we can offer measurement tests and material tests of all kinds on hard and soft magnetic materials. It is also possible to carry out measurements on site. We carry out stray field measurements on your magnetization station in production in accordance with the professional association regulations (BGV). We also carry out magnetic field measurements on air freight goods in accordance with IATA 953.