Showing recent results 1636 - 1650 of 4817 products found.
-
W-C-7312 - James Instruments Inc.
It is recommended that calibration of the test hammers be checked regularly usually after about 2000 strokes.The James Calibration Anvil (W-C-7312) has been designed for just that purpose.
-
CTS-02 - Nitto Construction Inc.
The revolutionary CTS-02V4 is a multifunctional, highly accurate portable concrete testing tool. The device measures and analyzes the quality of concrete by the waveform of impact force at the point of hammer and concrete contact, without causing damage. A built-in Accelerometer measures blow force. With the CTS-02V4 it is now possible to measure the strength of older, deteriorated concrete and high strength concrete (up to 150N/mm2).
-
HS-HCTT - HenergySolar
It is strictly designed according to the requirements of the hot-probe thermal EMF conductivity type test in standard ASTM F42: Standard Test Methods for Conductivity Type of Extrinsic Semiconductor Materials. A temperature controlling heating element is installed inside the hot probe so that the hot probe is heated automatically and its temperature is maintained in the range 40-60℃.
-
-
DRK8096 - Shandong Drick Instruments Co., Ltd.
Determination of compliance with national standards GB / T26991, were compact design, LCD display, automatic data collection and the corresponding statistical calculations, measurement report printout.It can connect the PC output data.The entire testing process is very simple, in full compliance with the provisions of the State Pharmacopoeia. Accurate measurement results, which has good reproducibility, stability of the system.
-
K10600 - Chongqing Kailian Yongrun Industrial Co.,Ltd.
It is designed to make penetration test of various kinds of lubricating grease and malthene. It is equipped with standard penetrating material of lubricating grease and malthene. Conforms to GB269 and ASTM D217.
-
VD-100 - Monacor International GmbH & Co. KG
Induction detector for voltages of 100-600 V ~ / 50-60 HzOptical and acoustic warningCAT III 1000VIntegrated LED lampPowered by 2x1.5 V Micro battery (n. Supplied)Dimensions Ø 26 mm x 176 mmWeight 30 g
-
-
26330 - Lisle Corp.
If the bulb lights up, continuity exists. If the bulb fails to light, the circuit is open. Not for use on live circuits, but incidental contact with 12V supply will not burn out LED bulb.
-
CT80 - Matco Tools
Buzzer and LED indicator give audible and visual signal when positive voltage is detected. Buzzer vibration for out-of-sight locations.
-
-
Compliance West USA, Inc
designed to perform the 60 Hz power line cross test/AC power fault tests required in GR 1089 issue 6 table 4.5 surge test 3,4, 4.3,and 6, and for UL 1950 section 6.4 paragraph 3 and 4.. Preset and Adjustable Time Settings Measuring Terminals including Voltage Sense and Current Shunt portals provide a safe location for users to accurately measure test voltages and output current while setting up tests. Calibration of the Mini_PT-600 is designed to be performed with a simple handheld multi-meter and the removable Currents Shunts can be easily sent to a calibration laboratory if required.
-
594 - Red Phase Instruments Australia Pty Ltd.
Utilities have always found a major problem in field testing PTs and CTs. The test equipment available for testing is generally very bulky, heavy, expensive and difficult to use. This new product from Red Phase employs a novel technique to test CTs. The operator keys in data for the CT under test. This data includes primary current, 1A or 5A secondary, VA rating, burden PF, accuracy class and serial number.
-
CTT - ndb Technologies Inc.
The CTT is designed to test the current transformer ratio, Phase shift, Polarity, Excitation, Saturation, Winding resistance and Insulation resistance using the voltage method in compliance with ANSI/IEEE C57.13.1 and IEC 60044-1 standards, where voltage is applied to the secondary X terminals of the current transformer.
-
Vanguard Instruments Company, Inc.
Performs CT excitation, current-ratio, polarity, and phase angle testsMeasures insulation resistance and winding resistance of the CT seconday windingsMeasures the CT's secondary burdenTest record header information including company, substation name, circuit ID, manufacturer, CT serial number, operator name, and test record-commentsBuilt-in 4.5-inch wide thermal printerPlot Multiple Saturation CurvesStores up to 128 CT test plans and 140 test records internallyUSB, Bluetooth, and USB Flash drive interface
