-
product
Long Term Test Kit
When long term electro-chemical tests (>1000 hours) are run to monitor the cell degradation at the cathode for example, it is important to avoid any contaminant in the gas flow rate.Inconel 601 flange equipped with alumina housing and alumina tube to feed the gas to the electrode during long term test (>1000 h)Typical poisoning is coming from the chromium contained in the steel tubing. The volatile chromium species (Cr6+) will flow into the cathode (with the air) and thanks to th...show more -
product
Turns Ratio Meter 1 Phase
TR-1 / TR-1P
Raytech Single Phase Transformer Turns Ratio Meter TR-1/P was designed to be a rugged and reliable automatic transformer Ratiometer. This system has a high degree of accuracy and will test ratios to 4000:1. The design of this test system is based upon the popular Raytech Automatic Three Phase test set: TR-Mark III.
-
product
Low Noise Test Cables For N1413 With B2980 Series, 3m
N1427B
The N1427B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It comes with a separate triaxial (special screw-type) female connector and a High Voltage BNC (special type) female connector. This allows terminal configuration to be converted to any other configuration. Therefore, custom test fixture can easily be constructed. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1427B to the B2985B/87B.
-
product
Ultra-High Performance FLASH and DRAM Memories Test Solution
Magnum V
Teradyne’s Magnum V systems delivers high throughput and high parallel test efficiency for ultra-high performance FLASH and DRAM memories. Magnum V’s largest configuration delivers up to 20,480 digital channels at 1600Mbps per channel.
-
product
ARINC 664 Part 7 Test & Simulation Interface for PCI
PCI-C664-V2
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfacesSimulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequ...show more -
product
PXIe CW Source, 1 MHz to 3 GHz or 6 GHz
M9380A
Save floor space with a compact, modular analog signal generator Provides Keysight quality and performance for local oscillator (LO) substitution, interference and component test Minimize need for external amplification with output power of +18 dBm across the frequency range Reduce test time with easy integration into your high-speed automated test system
-
product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
product
LED Tester
Pocket-size LED tester.Easily check functionality, color, brightness and uniformity.Plug any leaded LED into one of 12 positions on the socket strip to test at current ratings from 2-50ma.The seven middle positions on the strip are set at 10 mA allowing comparison of LEDs in those spaces.Requires a 9V battery (not included).
-
product
Insulation Resistance Tester
UDH-50-1-T
UDEYRAJ ELECTRICALS PRIVATE LIMITED
utomatic-microcontroller operated• Standard test voltages-0.5kV, 1kV, 2.5kV, 5kV • Resistance range to 1TΩ • Continuous digital display on LCM• Test modes: Insulation resistance,PI (Polarization Index)AR (Dielectric Absorption Ratio)(PI and AR automatically calculated)
-
product
Multi-Functional Dynamic System Monitor
PFMonitor
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
-
product
Automation Testing Services
Alphabin Technology Consulting
Delivering applications at lightning speed is as crucial as the high quality of the product, automating repetitive tasks with test automation services.
-
product
Battery Temperature Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
product
Keysight N7800A Test Management Environment (TME) Software
Special recommended calibration options: The N7800A software calculates point-to-point ISO GUM measurement uncertainty. The special “H-series” calibration options in the link below provide lower measurement uncertainties through use of direct comparison to devices directly characterized by NPL or NIST (or another NMI), along with data on a CD for easy import into the N7800A (avoids manual entry). The overall resulting N7800A measurement uncertainty then incorporates this lower device uncertainty in the overall calculated uncertainty. For more information on the special options please view this spreadsheet N7800A Special Calibration Matrix.
-
product
ELECTRONIC MEGOHMMETER
MI-5500e
The MI-5500e general purposes megohmmeter is a truly portable equipment suitable to measure insulation resistances using test voltages up to 5 kV. It employs high-reliable, state-of-the-art technology for accurate measurements of ultra high insulation resistances up to 10.000.000 MΩ
-
product
Stand-Alone Test Fixture
MA 2012/D/H/VPC-G12x-18
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: NoInterface signals max.: 1190Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 17,50 kg
-
product
Ultra Light High Voltage DC Test Sets
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
product
Parasitic Drain Tester
64970
Replaceable in-line fuses protect both the meter and tester in the event a high current source on the vehicle is left on. The multimeter is bypassed with the switch during connection in case of a power surge. The tester and meter can remain connected until other computer systems shut down, isolating the drain. As a convenience, stacking banana connectors are used on the tester. This allows voltage to be measured on various locations on the vehicle during the drain test, using standard test leads.
-
product
PANTESTER Multi Cable Tester
PK-7890/7890PL
PANTESTER is an advanced multifunction pin-by-pin cable tester to verify cable integrity of Datacom. Telecom and Coaxial cables and displays the test results on the main unit.
-
product
Test Leads
An IT professional who oversees the process of testing software before moving it to production.
-
product
CCTV testers
1.IPC Tester ,Support H.264/H.265 4K HD IP Camera.2.POE 48V Power Output,Max 24W;3.Support ONVIF, dahua, Hikivision, ACTi,samsung IPC.4. 4.3 inch 800*400 capacitive screen, image display more clearly;5.Built-in WIFI function,can test the Wi-Fi IP Camera;6.Support IP PTZ control functions (ONVIF).7.Support DC12V1A power supply output.8.Support Audio input test.9.Support 4K HD video files and Screen projection function.
-
product
IEC60068-2-75 Spring Hammer Test
CX-T03
Shenzhen Chuangxin Instruments Co., Ltd.
*Impact hammers are used to check the durability of enclosures for electrical appliances of other electronic products.If damage occurs from the Impact Hammer test .Accessibility probes can be used to measure the extent or severity of the damage.The Impact Hammer simulates the mechanical impact to which electrical equipment may be subjected. *This hammer is mainly used to test household and similar electrical appliances shell, lever, handle, knobs, lights and other shell to withstand mechanical shocks.* The impact tester made of stainless steel or alloy.
-
product
Multi-function Tester
MFT5010
It can be used to test insulation resistance, continuity, loop impedance and RCCB, earth resistance tester, five major test requirement in the electrical testing industry. Phase indicator. Can check a wide range of 3-Phase Power source from 110V to 600V
-
product
Voltage Integrated Sources
VIS
The VIS voltage integrated source was designed to be used as a stable alternating voltage source for electricity meter test equipment, and in laboratories. The output voltage is isolated and independent of mains voltage. VIS is available in a variety of configurations depending on the values of output power and output voltage.
-
product
PCI 9 Channel Precision Resistor Card
50-297-002
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Use UFT for mobile test automation
Mobile Add-On UFT
Use UFT only, no need for any additional tool Use UFT Object Spy Use UFT command auto-completion Receive reports in UFT including screenshots Test on local or remote (cloud) devices Supports iOS, Android, WindowsPhone, Blackberry Supports web and native object recognition Support QTP 11,11.5 and UFT 12,12.5
-
product
Protocol Analysis
GL's protocol analyzer provides monitoring a communication link in accordance with industry protocol standards by non-intrusively tapping the network under test. The simple framework of the protocol analysis software helps you easily identify the improper sequence of protocol messages, and filter out frames causing the protocol violation.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 3Ω to 5.82MΩ
40-252-052
The 40-252-052 is a programmable resistor module with 1 channel which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Ground Continuity Tester
HTDT-10A / 740
Wuhan Huatian Electric Power Automation Co., Ltd.
It is suitable for testing the conductivity of the connecting part of power equipment and ground network in engineering test of power department.
-
product
Turbidity Meters
Turbidity meters are needed in order to conveniently test the quality of various different areas of water that can be drinking water, including food processing and beverage manufacturing and many applications where fluid clarity is crucial.
-
product
Handover Test Systems
Family of handover test systems designed for handset-to-network handover testing. Internal step attenuators allow the RF signal between the network access points and the handsets to be dynamically faded up/down. The Ethernet/Serial models run our latest generation 3.x.x firmware that features easy to use ASCII formatted commands.
