Filter Results By:

Products

Applications

Manufacturers

Test

to find acceptable or limits of.

See Also: Testers, Testing, Specimen


Showing results: 3211 - 3225 of 14526 items found.

  • Test Solution Offering BER Testing

    Eye-BERT Micro LR - Spectronix

    The Eye-BERT Micro LR is a low cost, easy to use test solution offering BER testing at any rate between 6.312 and 125Mbps on either optical or electrical interfaces. Features include: continuously variable bit rate, user programmable pulse generator, internal CDR with retimer mode, bit rate measurement, and recovered clock output. The Unit is supplied with anti-skid bumpers for bench use, and is small enough to be integrated into larger systems for dedicated link verification.

  • UV Penetration & Protection Test System

    TF131 - TESTEX Testing Equipment Systems Ltd.

    UV Penetration & Protection Test System. Fabric Samples are measured in a double beam spectrophotometer with an integrated sphere. The sample is scanned over the UVA and UVB regions of the spectrum and transmitted radiation is efficiently collected by the detector within the integrating sphere. The software calculates UV penetration factors and sun protection factors from the scan data. It runs on a PC under Microsoft Windows and controls the spectrophotometer, automates the measurement process and generates a printed report. PC and printer are not included.

  • Real Car Transient Test System

    RealCar Simulation Bench - Ono Sokki

    This system is suitable for transient test of actual vehicle in combination with the real-time model calculation by the measurement/control panel and low inertial motor. By replacing the wheel of the actual vehicle with the tire type bearing, the axle shaft is taken out to the outside of the vehicle and connected to the low inertia motor. It can be reproduced the sliding motion which the chassis dynamometer cannot be realized. Also, since the longitudinal force is not occurred in the vehicle, the vehicle restraint can be simplified and the behavior such as shift shock can be reproduced on the bench.

  • Test Sets For Motor & Generator Industries

    NEO TELE-TRONIX PVT. LTD

    Test Sets For Motor & Generator Industries are designed for no-load loss as well as heat run testing. They are ideal for offering clean power with precise regulation as well as voltage control. These sets are designed when there is no need of frequency conversion. With variable-frequency drive of these sets, they are used to select any output frequency from 50 Hz to 60 Hz. in addition to this, for larger requirements, from 50-to-200 Hz, this has been used as one of the most economical testing sets.

  • Uniload Voltage Transformer Test Set

    2J6 - The Eastern Specialty Company

    The Type 2J6 Knopp Uniload Voltage Transformer Test Set consists of three major parts: When the Knopp Precision Transformer in the 2J6 set is compensated for, and used with, a secondary burden of 15 volt-amperes, for example, the ratio of this precision transformer is well within 0.02% and the phase angle is well within 2 minutes. The transformer, in common with other Knopp Precision Multirange Transformers, is wound so that it has practically the same ratio and phase angle accuracy on all ranges.

  • LED Optical Aging Test Instrument

    LEDLM-80PL - Lisun Electronics Inc.

    LEDLM-80PL LED Lumen Maintenance and Aging Life Test System is designed according to standards of IES-LM-80, IES-LM-82, TM-21 and GB2312-80, and the software is developed base on Arrhenius model. LED has the features of long life, but with the different working condition and drive current, its life will be different, but generally the life will be around 50K hours. Differ from the traditional lightsource, LED light will decay gradually rather than extinguish instantly, so in the standard of LM-80, it introduces L70, L50 and etc.

  • PCX Multimeter Test Leads Clip

    Parrot Invent

    - The PCX Parrot Clip model is aimed to be used mainly for multimeter test leads.- When is hand held, is a handy device giving comfort to the operator.- The PCX Parrot Clip model is effective for direct point, hands-on measurements.- It has a length of about 130 mm so that it points with the metal tip places rather crowded with electronic components.- The PCX provides also reliable hands-free connections.- Even that is rather long the PCX model is not heavy, and therefore the weight of the probe is not affecting and forcing the connection.

  • Circuit Break Timer Test Set

    PME-500-TR - EUROSMC, S.A.

    Before developing the system or equipment for the testing of a circuit break timer for distribution, the application information was obtained by consulting various users of this type of timer for circuit breaker. The customers consulted were from private service and maintenance companies, large industries, and of course from the Utility companies. It is essential to receive first hand information of the actual requirements and needs of each of these customers who are making these types of tests and then make a detailed study of the various alternatives offered by different manufactures of this type of circuit breaker timer.

  • Mobile HV AC Test System

    Power Diagnostix Systems GmbH

    The system stays within the load and size limitations for permission-free road use. Additionally, the matching transformer and the reactor are filled with ester instead mineral oil. Thus, it can be easily transported to a substation, power plant, or other high voltage areas for testing HV components after installation or repair. Additionally, it is applicable for condition assessment and fault investigations. PD measurements can be performed in non-shielded environments as part of the on-site acceptance test on a power transformer, or as a method to locate PD failures acoustically, or by electrical measurement.

  • Relay Test Jumper Kit II

    60610 - Lisle Corp.

    Set includes four jumpers to fit many popular relays on Honda, Nissan, Toyota, newer Ford and GM mini micro relays as well as International trucks. Set comes in blow-molded case for storage. Simply remove relay to be tested, insert correct jumper and insert relay into jumper. When using grey four pin jumper be careful to align pins on jumper and relay correctly. No need to pierce wires or connect multiple jumper wires. Jumpers have tabs for clamping and flat pads to place test leads on.

  • Modular Circuit Breaker Test Set

    PI-800 - ETI Precision

    The PI-800 Circuit Breaker Test System incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-800 generates continuous current of 800 amps at 4.2 kVA, with peak output to over 10x, on 120 or 240 VAC supplies. The units are housed in rugged interlocking suitcase sized enclosures. Each piece weighs no more than 125 pounds, allowing one person hand truck mobility. Basic operation is very simple, and the proven MAC-21 instrumentation provides optimal output control and measurement.

  • Imaging Gauge Software Test System

    Applied Image, Inc.

    The IMAGING GAUGETM quality analysis system was developed by APPLIED IMAGE to address the growing need to standardize the evaluation of camera image quality. The system includes a Test Chart manufactured using our ACCUedge® technology, along with unique Image Analysis Software, used together to analyze the quality of the imaging system, and then provide a summary report on the various image quality metrics. Our goal is to provide a simple to use, unique image analysis system, that can be utilized by R&D, scientists, system integrators, technicians and field operators to evaluate the camera quality or imaging system.

  • ARINC HSI / ADI Test Fixture

    TA-2000 - Tech-Aid Products

    The TA-2000 test fixture is a combination panel that incorporates all the standard capabilities of the legacy CTS-11(ADI) and CTS-12(HSI) panels and much more. This panel is married to our model TA-1001 dual synchro transmitter/API panel thus allowing for local stimulus and alignment of the instruments synchros and resolvers. The panel provides for testing of both superflag(28v) and low level meters through a matrix of switching that will allow testing of all meters simultaneously or just individually. The low level meter drive circuit also incorporates an automatic mode that will continuously oscillate the L/R and Up/Dn pointers.

  • High Speed Machinery Test Rigs

    Barbour Stockwell, Inc

    designs and builds all kinds of rigs for testing the components of high speed machinery. As in our spin pits, BSi's unsurpassed ability to generate and precisely control extraordinarily high speeds is the key competitive advantage. BSi engineers also draw on our vast experience to provide reliable drives and rigs to meet the most demanding requirements under the most extreme conditions. We have engineered and manufactured rigs for testing bearings at speeds to 250,000 rpm. We have delivered test benches for testing abradable seals at temperatures to 1100 deg. C.

  • Material Compatibility Test System (MCTS)

    MB Dynamics Inc.

    Automotive squeaks occur when materials in contact rub against one another causing annoying noises from friction-induced stick-slips. Automotive itches are a special category of squeaks that can develop when rubber or plastic rubs against glass or paint. The MB Dynamics Material Compatibility Squeak & Itch Test System (MCTS) is designed and manufactured to subject contacting pairs of materials and actual vehicle parts to precisely controlled interference & motion under in-vehicle environmental conditions in order to acquire, monitor, analyze and report friction and acoustic characteristics with the objective to:

Get Help