-
product
2.92 mm to 2.92 mm Test Cable
C50292MM
Our 2.92 mm test cable is made to ideally suit our larger line of vector network analyzers. The C50292MM test cable operates at a frequency of 40000 MHz and is compatible with our PC-driven vector network analyzers.
-
product
Preamplifiers
Com-Power broadband high gain preamplifiers were designed for electromagnetic interference (EMI) testing and certification. EMC test labs use preamplifiers to improve sensitivity of the test system during EMI radiated emissions measurements. Without a high gain preamplifier, signals picked by the antenna that have amplitudes below the noise floor of the test system cannot be measured. The preamplifier gain has minimum variations for the entire operating frequency range for accurate emissions measurements. The Com-Power preamplifiers were primarily intended for EMC applications. However, it can be used for other applications that require signal amplification.
-
product
Micro Vickers Hardness Tester
900-392
The 900-392 Micro Vickers Hardness Tester is engineered to produce a clearer indentation and hence a more precise measurement. By means of a 10 × lens and a 40 × lens the 900-392 vickers hardness tester has a wide measurement field and a broad usage range. Equipped with a digital microscope, it shows the measuring methods, the test force, the indentation length, the hardness value, the dwell time of the test force as well as the number of the measurements, all shown on its LCD screen.
-
product
CAM/TRAC Test Kits
Series 40
The CT Series 40 CAM/TRAC mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance.
-
product
In-Circuit Testing and Test Engineering
Teradyne Z1890
2048 Pure Pin Test Nodes3 & 6-wire Analog MeasurementsVector Test for VLSI, PLCC’s & ASICSMultiscan II Vectorless TestingIEEE Functional Interface BoardLarge Custom Vector Library
-
product
Analog Phase Shifter
Analog Devices analog phase shifters change the phase of RF, microwave, and millimeter wave signals. Our technology features consistent insertion loss vs. phase shift, monotonic phase shift, low insertion loss, and a compact size that makes it ideal for multiple applications, including:• Fiber optics• Military• Test equipment
-
product
USB Explorer (Two Port)
JT 3705
The JT 3705/USB Explorer is a low-cost two port USB powered boundary-scan controller interface specifically suited for low volume testing and in-system programming of (C)PLDs. Explorer supports two fully-compliant boundary-scan test access ports (TAPs) which can be synchronized for test purposes.
-
product
High Speed Optical Power Meter
Shenzhen Golight Technology Co.,Ltd
High-speed optical power meter has fast sampling and data cache functions, and supports external trigger input and analog output. It is built-in 2mm or 5mm photosurface detector, and has wide dynamic range and high measurement accuracy, can be applied to various optical loop test solutions.
-
product
Textile Test Equipment
AVENO textile testing equipment including fabric tester, yarn tester, fibre tester, related abrasion tester, color fastness tester, strength tester, flammability tester, snag tester, pilling tester, and more. Mainly used to check the quality of textile products.
-
product
AC/DC Clamp Meter
3810 CL
Standard Electric Works Co., Ltd
● Full auto range for V.A and Ω functions.● Data hold function freezes the reading in dimly lit or hard to reach places.● Low battery indication.● Built-in buzzer for continuity test.● Safety design throughout with no exposed metal parts. Shielded banana plugs and recessed input terminals.● Ohm function ideal for checking continuity of relays transformers and motor coils.
-
product
AC Hipot Tester
298
Our Model 298 is a simple-to-use 500VA AC Hipot Tester with the built-in ability to test Ground Continuity (Low Current Continuity). The 298 500VA AC Hipot Tester includes all the features you need to get the job done and move on.
-
product
Advanced Power System - DC Power Supply, 80 V, 12.5 A, 1000 W
N6954A
The N6954A is designed for automated test equipment (ATE) applications where high performance is critical.
-
product
x1149 Boundary Scan Analyzer
N1125A
The x1149 is a tool for engineers to perform structural test such as opens and shorts tests on their PCBAs. It also performs In-System Programming for devices such as FPGAs and CPLDs.
-
product
Cylindrical Mandrel on a Stand
1500
The Elcometer 1500 Cylindrical Mandrel on a stand is a simple instrument for determining the elasticity, adhesion and cracking of dry paint on flat specimens, consisting of mandrel support which also serves as a test stand.
-
product
Safety Test Panel for Luminaire Fixture
SCR ELEKTRONIKS introduces Safety Test Panel for Luminaire with PC Datalogging. The tests are Performed as Prescribed in IS the Panel Carries out different tests one by one and provides indication of the Test results as OK or NOT-OK. It is very useful and handy in line testing on Mass production line as well as type Testing.
-
product
Component Test
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
product
Single Stream STANAG3910 Electrica lTest And Simulation Module – Rafale – for PCI
APXX3910-EN
Single Stream STANAG3910 Test and Simulation Module – Rafale – for PCI with 1 dual redundant HS/LS channel and onboard Electrical Front End. The APXX3910-EN is a functional replacement for model APX3910-EN.
-
product
Asynchronous System Level Test Platform
Titan
The Titan System Level Test (SLT) platform delivers maximum flexibility, scalability and density in semiconductor test environments that require the highest levels of system performance testing. Titan is Teradyne’s solution for high-volume mobile application processor SLT requirements.
-
product
Four-Wheel Drive Single Roller Dynanometer for Cars with Axle Load of up to 2.4T
MSR 500/2 CAR 4WD (ADD. BRAKE) | VP 230041
Maschinenbau Haldenwang GmbH & Co. KG.
The MSR 500/2 CAR 4WD single roller dynamometer is used in workshops for designers and tuners as well as in educational institutions. It is especially suitable for performance measurements, tuning and diagnostic work on particularly powerful vehicles. With test speeds of up to 300 km/h, it is used for dynamic and static power measurement. The MSR 500/2 CAR 4WD guarantees optimum measurement accuracy and reproducibility through the active measurement of the towing power.The rolling behaviour of t...show more -
product
PCI Precision Resistor Card 4-Channel, 1.5Ω To 472Ω
50-297-120
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
20V/30A/300W DC Programmable Electronic Load
TOB-IT8512
Xiamen Tob New Energy Technology Co., Ltd
IT8512 120V/30A/300W DC Programmable Electronic Load for Battery and Power Supply TestHigh performance and affordable single channel DC electronic load. TOB-IT8512 DC electronic loads provide you with the flexibility to test a wide range of applications from power supply, charger to battery. The high resolution voltage(1mV), current(0.1mA) measurement system provides both accuracy and convenience, and eliminates the need for a DMM, external shunts and wiring.
-
product
Automatic Winding Turns Tester
This tester has the advantage of high accuracy and efficiency, limited influence due to the form and size of the coil to be analyzed, and fast & easy operation thanks to the precision sensor and microprocessor that adopt the patent know-how developed by the manufacture. This tester, when in operation, does not need any further adjustment and calibration. Just connecting the clip leads to each terminal lug of the coil winding, then the tester instantly shows the exact number of the winding tu...show more -
product
Auxiliary Lamp
RLS-50W
Due to the luminaries self-absorption, the auxiliary lamp is used to correct the flux test value. Work with the follow instruments as a System
-
product
Seam Fold Test Device
FFR1000
This equipment is designed to bend a flexible printed circuit board, which has a high degree of freedom and versatility, and at that time, apply a load to the bending point at the initial stage or each time, and repeat bending and unfolding to confirm the durability.
-
product
Air Quality Tester
Choose a CO or CO2 meter to perform tests in labs, hospitals and plants. These meters help ensure the air quality is safe by warning you with visual and audible alarms when gasses exceed safe levels.
-
product
Test Automation System
RT-Tester
Verified Systems International GMBH
Designed to perform automated hardware-in-the-loop tests and software component test on process or thread level for embedded real-time systems. The functional components of RT-Tester can be structured as shown in the figure to the left. Please click on the small image to enlarge the picture. The System Under Test (SUT) denotes the object to be tested.
-
product
Transducer Test System
TTS-030
For the generation of unique bond links the use of high-quality components is an essential precondition. Despite all care in the production of ultrasonic transducers again and again unexpected effects occur, which only manifest themselves in the use of those transducers and which also have the reason in the transducer itself.
-
product
Analog Test Instruments
Analog test building blocks for high performance ATE. VXI-based Core System Instruments (CSi) ZT-Series™ PXI/LXI instruments.
-
product
EMI Test Receiver
ESRP
The R&S®ESRP EMI test receiver has been designed for diagnostic measurements during development and for precompliance measurements to prepare products for final certification testing. It measures electromagnetic disturbances in the 10 Hz to 7 GHz frequency range, using either conventional stepped frequency scans or FFT based time domain scans to significantly speed up measurements.
-
product
Battery Impedance Tester
KT-97
3 1/2 digits, Max. reading 1999. Test battery Impedance. Test Voltage online. Resolution upto 0.1m¦¸ Fit to test battery: lead-acid, Li-ion; Ni-HM, etc. Judge battery capacity
