-
Product
Generator/Analyzer for NFC/EMVCo Manufacturing Test
Micropross MP500 PT1-NFC
test
Support for ISO 14443 A/B, ISO 15693, MIFARE™, FeliCa™. Measurement correlation with NFC Forum and EMVCo certification test bench. Automated test executive with ready-to-run test sequences. Reader/Writer and Card Emulation modes, resonance frequency measurements supported on same antenna. Embedded analog measurements - LMA, field strength, S11, Q factor, waveform characteristics. Physical parameter/waveshape characteristic definition
-
Product
Photodiode Burn-in Reliability Test System
58606
Test System
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Circuit Testing
Tester, Circuit GFI
-
*Use to troubleshoot 120 VAC grounded outlets and test GFCI receptacles*Light sequence indicates correct/incorrect wiring*Lifetime Limited Warranty
-
Product
Other Test Systems
Test System
Your business challenges do not fit the typical mold. Your test requirements are different. Ball Systems has more than 50 years of experience in multiple industries that has exposed our team to a wide variety of testing applications. As a result, we’ve likely created a solution for a challenge similar to yours.
-
Product
Test Executive for Visual Development, Database Storage, and Run-Time Execution of Test Strategies
TestBase
-
TYX TestBase is a test executive that supports the visual development, database storage and run-time execution of test strategies (also known as test plans or test sequences).TestBase integrates third-party applications such as: test programming languages, document viewers, report generators, database engines, Configuration Management systems and diagnostic tools.Its modular and open architecture enables system integrators and end-users to customize and extend the product and to integrate additional third-party applications.
-
Product
2m BNC Test Cable
16048D
Test Port Cable
The 16048D test leads extend the measurement port with a 4-terminal pair configuration. It provides a BNC female connector board to allow attachment of user-fabricated test fixtures.
-
Product
HSI System Test Panel
TA-500
-
This panel was designed to test primarily the NSD360 series of HSI systems. Panel allows running the complete system on the bench. Included is a panel mounted TA-902 API which can also be used for testing external instruments via a panel mounted switch. The API and standard meter drives allow testing many different instruments.
-
Product
Test Pressure Gauge with Pump
-
We make available for our valued clients SI 3000/4000 series Test Gauges/Master GAUGES. These are made from high qualityberyllium copper bourdon tube, and provide precision movement and knife edge pointer with anti parallax. further, the range for SI 4000 series test gauges is ±0.5% FSD, while for master gauges it is ±0.25% FSD. Clients can avail these gauges at industry leading prices.
-
Product
6TL60 Rotary Test Handler
H79006010
Test Platform
6TL60 has been designed according to the 6TL philosophy, following the concepts of flexibility, modularity and scalability, and with the aim of improving production efficiency as well as increase production capacity and reduce costs.The 6TL60 is the best production solution to automate test processes to reduce the cycle time and the footprint used in the manufacturing plan
-
Product
Performance Testing
-
LOAD TESTINGEvaluates software behavior under a specific expected loadVOLUME TESTINGEvaluates software productivity under an increasing volume of stored and processed dataSTABILITY TESTINGDetermines the effect of configuration changes on the system's performance and behaviorSTRESS TESTINGIdentifies the upper limits of software capacitySCALABILITY TESTINGMeasures software capability under increased processing power and architecture changesCONFIGURATION TESTINGDetermines the effect of configuration changes on the system's performance and behavior
-
Product
Performance Testing Services
-
Alphabin Technology Consulting
There are over 1.5 million mobile apps that are abandoned due to performance issues. Guard your application with our performance testing services.
-
Product
Battery Test Equipment
-
Batteries are the heart of many Stationary, Critical Power, Industrial and Motive Power applications which means they need regular monitoring and testing to ensure they can deliver power on demand. We give you the correct products to monitor and test batteries’ capacity.
-
Product
Test Automation System for Emission Testing
STARS VETS
-
STARS VETS is a Vehicle Emission Test System application available with the STARS Automation platform for chassis, engine and powertrain dynamometers. The application provides test cycle execution, emissions equipment control, results calculation and reporting in compliance with the different legislative standards throughout the global regions. Its flexible design offers a wide range a customization, and it addresses the various requirements for R&D, COP and certification testing.
-
Product
EMI Test System
TS9975
Test System
The R&S®TS9975 is the base system for conducted and radiated EMI measurements. Due to its modular design, it covers a wide range of applications and can be very easily adapted to the measurement task at hand. Any configuration is possible – from conducted measurements and the small precompliance system with a compact test cell to the accredited test system for large equipment under test. Combinations of different applications or incremental expansion are easily possible.
-
Product
5G | OTA | Bluetooth | PTCRB Testing Services
-
Eurofins E&E Wireless Device Over-the-Air (OTA), 5G Performance, Bluetooth, PTCRB, and Global Certification Forum Testing.
-
Product
Probe Needles for Wafer Sort and Test Applications
-
Advanced Probing Systems, Inc.
APS is the global leader in the manufacture of probe needles used in cantilevered probe cards. All probe needles used in wafer sort are manufactured according to customer specifications using stringent in-process quality assurance procedures.
-
Product
Component Test Fixture For N1413 With B2980 Series
N1428A
Test Fixture
The N1428A is designed to operate specifically with the B2985B / 87B electrometer / high resistance meter. It is provided with two component modules, which are used to hold SMD, lead, and various types of devices. Electrical noise effects are reduced by the employment of a shielded case. A built-in interlock circuit enables safe high-voltage measurements. The N1413A high resistance meter fixture adapter is also required to connect the N1428A to the B2985B / 87B.
-
Product
Cable Test Van
BAUR Transcable 4000/S 110-1
-
Transcable 4000/S 110-1. The transcable 4000/S 110-1 cable test van is a 110 kV cable fault location system in single-phase version. The system is actuated with the semi-automatic MGS control unit. The high voltage switch unit is single-phase, up to 32 kV, the 110 kV switching level is designed as air-insulated ceiling switch.
-
Product
Burn-In Test
-
C.C.P. Contact Probes Co., LTD.
Customized Burn-In Test Sockets for temperatures of up to 180°C.
-
Product
Portable Meter Test Systems
-
Zhengzhou SMS Electric Co.,Ltd
Portable energy meter calibration test devices.
-
-
Product
Test Probes & Clips
-
CF Instrument Accessories Ltd.
CF Instrument Accessories Ltd. Test Probes & Clips
-
Product
Memory Test Software
-
Teradyne’s customers count on us for our Near Device Under Test (DUT) technology that gives memory device manufacturers a guaranteed performance advantage. A brief description of dynamic memory and storage memory devices will highlight why device manufacturers depend on Teradyne’s memory test solutions.
-
Product
Lithium Battery Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
Product
Performance Testing
-
All of Xena’s products can be used for performance testing. This typically includes measuring:*the volume of data successfully delivered between two points, usually measured in bits or packets per second*how long it takes data packets to travel between two points in a network or a device, also known as latency*variations in latency – also known as jitter – due to network congestion or other factors*how many data packets fail to reach their destination*if data packets are delivered in a different order from that in which they were sent
-
Product
N-Male to F-Male Test Cable
C75NMFM
-
The C75NMFM is a high performance 75 Ohm test cable that is ideal for performing lab grade measurements 75 Ohm environments. It supports high accuracy testing with low insertion and excellent return loss up to 3GHz as well as outstanding mechanical durability.
-
Product
Test Fixtures-Assemblies
-
Qmax Test Technologies Pvt. Ltd.
Test Clips are available for various types of DIP ICs like 8, 14, 16, 20, 24, 28, 40, 48 & 64. These can be supplied with or without connectors and cables for interfacing to Qmax Testers. Test Pins in the clips are gold plated and engineered for good contact with the Device Under Test. It is designed for long life and trouble free operation. For easy handling the clips are provided with metal covers.
-
Product
Adapter/Stainless Steel
WADP-24F29F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Automotive Engine Tester
QCM-2A
-
Changzhou Chanlon Electronic Technology Co., Ltd.
This tester is applied to integrated test varieties of automobile motor, wiper motor, window lifting motor, oil pump motor etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stators.
-
Product
Mini-Link™ Miniature Jumper
Series ML-100
-
Mini-Link Miniature Jumpers. Used to jumper from row-to-row or from pin-to-pin. Their miniature size makes it possible to stack one on top of the other. A convenient test probe slot is provided as well. Mini-Links are available from the factory with or without a handle, used for ease of inserting or extracting.
