Showing results: 2371 - 2385 of 8242 items found.
-
Model 52624 -
Pentek, Inc.
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
PA72G16400 -
APPLICOS
The PA72G16400 is a 16-bit arbitrary waveform generator, capable of generating waveforms at speeds up to 400Msps. The high resolution and the high sample rate allows generating signals with very low quantization noise levels. An onboard offset voltage source allows generating offset signals while maintaining optimal utilization of the DAC’s digital range. With the 8MWord of memory, there is lots of room for uploading several different patterns, allowing switching patterns with minimal bus communication.
-
CS448 -
Cleverscope Ltd.
Four 1kV isolated analog channels and 8 digital channels, a 0-65 MHz isolated signal generator, USB 3, a 1 Gbit Ethernet port using an SFP socket for either wired or optical ethernet connection, and a general purpose 16 pin mixed signal control port using programmable hardware (a Silego SLG46533V) which includes trigger in and trigger out connections. The CS448 has 256 M Sample storage.
-
AMC SyncClock32 -
Brandywine Communications
The AMC-SyncClock32 from Brandywine Communications is an Advanced Mezzanine Card (AMC) module. Precision time is provided to the host computer with zero latency. The onboard microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs handled by the AMC in its standard configuration are IRIG’s A, B/IEEE1344, and NASA 36. Alternatively, the clock in the AMC can be set using commands from host computer and free run using its on-board oscillator as the time base.
-
D Series Boards -
Silver Engineering, Inc.
D Series Breakout Boards are open designs that provide signal access when troubleshooting. Signal connections are accomplished by inserting or removing Mini-Jumper plugs. All normal and high density D type connectors are available. Current carry capability is from 2.25A to 5.3A. Normal Density D Type: 9, 15, 25, 37 and 50 positionsHigh Density D Type: 15, 26, 44, 62, 78 and 104 positions
-
40-675-002-99/2 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-675-002-198/1 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-675-002-49/4 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-675-002-24/8 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-675-002-10/16 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
40-675-002-5/32 -
Pickering Interfaces Ltd.
The 40-675 series of very high density low cost multiplexer modules are available in a versatile range of switching configurations. The modules are supplied pre-configured in one of six multiplexer modes suitable for signal routing in high channel count ATE and data acquisition systems. The modules use high quality electromechanical signal relays allowing each channel to switch current up to 1A at 150VDC/100VAC. Connections are made via a front panel 200-pin connector.
-
KRYTAR, Inc.
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
KRYTAR, Inc.
KRYTAR’s directional couplers are uniquely designed for systems applications where external leveling, precise monitoring, signal mixing or swept transmission and reflection measurements are required. These couplers provide simple solutions for many applications including electronic warfare (EW), commercial wireless, SATCOM, radar, signal monitoring and measurement, antenna beam forming, and EMC testing environments. For many space-restricted applications the compact size makes KRYTAR directional couplers ideal solutions.
-
SEP/SIP -
Nihon Denji Sokki Co., Ltd
There are analog phase control type DC power supply type and digital control type inverter energy saving type. We provide the most suitable equipment according to the current capacity and cycle time.If the "start command" is executed from the existing molding equipment, each mode of "alignment-pause-demagnetization" is continuously operated by the program inside the instrument. It is also possible to share an emergency stop signal and output an output current abnormality signal.
-
SFT3975C -
Hangzhou Softel Optic Co., Ltd.
SFT3975C HD IRD is SOFTEL’s new product which can receive signals from tuners (DVB-C, DVB-T/T2, DVB-S/S2/S2X, ATSC-T, ISDBT optional), ASI and IP. After demodulating, de-scrambling, re-multiplexing and decoding, it gives content out through various video/audio interfaces (HDMI, CVBS, 3G-SDI) or ASI or IP. This IRD is featured with two CAM/CI slots and BISS which supports to descramble encrypted Tuner, ASI or IP signals.