Resistance
that which keeps current from flowing freely.
See Also: Resistivity, Resistance Standards, Resistance Meters, Resistance Test, 4-wire
-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1V-6
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-043
The 40-297A-043 (PXI) and the 42-297A-043 (PXIe) are 6-channel programmable resistors with a range of 2.5 Ω to 773 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Back and Forth Scratching Tester
WGQ-60
Shanghai Dean Electrical Co., Ltd
Executive standard: NEMA、JIS; Inspection standard: JB/T4279.15-2008Used to detect the scraping resistance of coating and cable insulation layer of flat wires of 0.800～5.600mm (narrow side) and the silk and enamel covered round wires with nominal conductor diameter of 0.100～5.000mm;Application of SCM control allows for fast operation and strong anti-interference capacity;Sample support table allows for parallel rise and fall, maintaining close contact between the entire plane with sample;Scratching needle is vertical to the paint scraping direction and parallel with sample supporting table;When film is scratched and the action current is ≥5mA, painting scraper would automatically stop scraping;LED would automatically display the number of scraping.
-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1H-6-S
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Ultrasonic NDT Transducers
United Western Technologies Corp
The Quick Change Transducer (QCT) series of transducers that makes changing wedge angle and transducer frequency rapid and easy, saving both time and money. The QCT connects straight into the wedges allowing for many combinations all within one kit. All QC Transducers are fitted with top mounted microdot connectors allowing for seamless transition from one transducer to the next. The stainless steel transducer housing will resist even the harshest working conditions. The emphasis of the QCT is general purpose with a balance of power and resolution, a High resolution version is available upon request.The Quick Change Wedge (QCW) is simple to setup and operate, utilizing incorporated noise dampening material on the wedge. Offered in steel, aluminum and titanium refracted angle. Custom contours, radii and wear pins available upon request.The QCT and QCW series are extremely versatile and can be used in many different applications and in a wide variety of industries and environments.
-
product
Handheld Digital Multimeter, 4.5 Digit, Water and Dust Resistant
U1273A
Organic LED (OLED) display for high brightness level and wider viewing angles (up to 160 degrees)Features set that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.6% for ACV accuracy)Intelligent features to improve productivity and safety (LPF, ZLOW, Smart )Better grip Visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 10,000) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
product
PXI High Density Precision Resistor Module, 18-Channel, 2Ω to 31.5Ω
40-298-010
The 40-298-010 is a high density programmable resistor module with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Digital Insulation Testers
This professional Voltage Insulation tester is designed with voltage overload protection and high voltage indicator to safely measure voltage in 50V, 100V, 250V, 500V,1000V and 2500V. It has a dual display when measuring under Insulation Resistance, it simultaneously show the selected voltage range and insulation resistance measured reading. These measurements can be use to evaluate insulation integrity. This troubleshooting tool is a quality control measure at the time a piece of electrical equipment is produced and an installation requirement to help ensure specifications are met and to verify proper hookup. It also use as a periodic preventive maintenance task.
-
product
Standard 1.00 (28.00) - 2.75 (78.00) Non Replaceable General Purpose Probe
E-S-C
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 65Full Travel (mm): 1.65Recommended Travel (mil): 43Recommended Travel (mm): 1.09Overall Length (mil): 495Overall Length (mm): 12.57Rec. Mounting Hole Size (mil): 67Rec. Mounting Hole Size (mm): 1.70Recommended Drill Size: #51Overall Length Remark: Overall length for E-S-V and E-S-W is .540 (13.72)
-
product
Precision Thermometer
F252
ASL's F252 provides high accuracy, dual channel temperature measurement with Platinum Resistance Thermometers - PRTs - and uses AC bridge technology as developed by ASL for Standards Laboratories throughout the world. Model F252 requires no regular recalibration, the AC circuit techniques eliminating thermal EMFs and drift, while providing excellent long term stability. Front panel data entry allows you to enter probe calibration data into the F252's memory, so that thermometer resistance can be accurately converted to temperature in C, F or K. This can be password protected to prohibit unauthorised or accidental data entry.
-
product
PCI Precision Resistor Card 9-Channel, 1Ω To 31.5Ω
50-297-110
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
RUB-01
Rub Tester
Jinan Leading Instruments Co., Ltd.
RUB-01 Rub Testerisapplicable in abrasion resistance test of printing works, light sensitive layer of PS boards, and coating layers of relative products. It can help users toanalyze the affairs of lower abrasion assistance, ink layer falling-off, lowerprintable of PS boards, and rigid of coating layers of other products.
-
product
Digital Insulation and Continuity Tester
Metra Insu 20
Measurement of the insulation resistance on electrically dead equioment and systems with test voltages up to 1000 V. For testing motors, transformers, generators, switchgears. For testing of house hold appliances. Measurement of the insulation resistance of cables. Very useful for on-site maintenance and service departments.
-
product
Conductive Footwear Tester
SLTM-1
SLTM-1 Conductive Footwear Tester checks conductive footwear automatically. The SLTM-1 Conductive Footwear Tester automatically and accurately measures the exact amount of resistance in conductive footwear and body grounding devices, ensuring a static control environment. It is ideal for dangerous, potentially explosive areas or areas in the electronic industry where static can destroy sensitive components. Stand on the foot plates and the unit’s direct-reading dial with graduated, color-coded scale indicates the exact amount of resistance. Shipped complete and ready to operate. Has 8 feet of 18-3 type SJ power cord that plugs into any grounded 120-volt AC power source. This unit measures 17 x 12 inches and weighs less than 6 1/2 lbs. All conductive footwear and body grounding devices, such as LEGSTATS, must be worn in pairs. SLTM-1 passes conductive footwear with resistance less than 2.5 MEG Ohm.
-
product
Full Wave Recorder
I-FullWaver
The I-FullWaver systems were specifically developed for precise full waveform time domain induced polarisation, Resistivity and self-potential measurements. Each system is fully independent; incorporating its own power source, GPS module and digital memory for up to 3 months continuous recording.
-
product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-FK180-2
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
Salt Spray Machine
UI-E01A
Salt Spray Machine – Salt Spray Test Chamber is used to test material Corrosion resistance by producing salt fog. So it is also called salt fog test chamber. This salt spray cabinet is widely used in painting, coating and other industries. Salt Spray Test Method includes ASTM B117, B268, CNS 3627, 3885, 4159, 7669, 8886, JIS D-0201, H-8502, H-8610, K-5400, Z-2371, ISO3768, 3769, 3770, GB/T2423, GJB 150 and etc.
-
product
PXI Precision Resistor Module 9-Channel, 1.5 to 925
40-297-021
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Elevated 2.65 (75.00) - 6.50 (184.00) High Performance Lead Free Probe
LFRE-25V-6.5
Current Rating (Amps): 8Average Probe Resistance (mOhm): 8Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Light 0.83 (24.00) - 2.00 (57.00) Bead Probe
BTP-1HC-2
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Wide Range Ohmmeter
PAS-853B
- Wide Resistance Measurement Range from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period Control- Automatic or Continuous Electrification ControlRugged High Performance 80 inches (200cm) Test Leads Included- Powered by one long lasting 9V Alkaline Battery- Large, Easy to Read LCD Display- Meets requirements of ESD Association Standards for material and audit resistance measurement requirements- Certificate of Calibration Traceable to NIST included
-
product
Switch Mainframe
SW1002
Switch between voltmeter and battery tester while testing. 264 channels max. (2-wire) to 72 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
product
Light 0.83 (24.00) - 2.00 (57.00) High Performance Lead Free Probe
LFRE-1I8-2
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-014
The 40-297A-014 (PXI) and the 42-297A-014 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 470 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
-
product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 31.5Ω
50-298-010
The 50-298-010 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Single 24x8 Matrix, 1 Pole Switching
40-521-021
An ultra high density matrix module is configured as a 24x8, this range is availablein a choice of reed relay formats: 1-pole (shown here), 2-pole and 1-Pole screened. The screenedversion is suitable for switching signals up to 50MHz. Typical applications include signal routing in Functional ATE and data acquisitionsystems. These PXI matrix cards are constructed using high reliability RutheniumElectro-Plated Reed Relays, offering >10e8 operations to give maximum switchingconfidence with long life and stable contact resistance.
-
product
Electric Vehicle Battery Tester
The Electric Vehicle Battery Tester (EVT) is designed for testing traction batteries in electric vehicles or HEV batteries in hybrid electric vehicles. The EVT realizes the functions charge and discharge with freely programmable set values for current, voltage, power or resistance in test programs, as well as the registration of the corresponding measured data.
-
product
Kelvin Test Contactor
cCruiser
cCruiser™ Kelvin contactor was designed with cost of test optimization in mind, boasting a cantilever design that allows the testing of challenging discrete ICs and small logic package types. Providing a best-in-class proven lifespan of up to 5 million touchdowns increasing handler uptime. cCruiser reduces the cost of test for customers significantly, lasting longer and testing longer than previous contact solutions.cCruiser is the versatile solution for testing small discrete ICs. Its side-by-side Kelvin design is optimized for tri-temp capable insulation layer with extended Automotive temperature range -60°C to + 175°C. Contact socket is G-Pin footprint compatible with a contact spring wear out zone. Featuring conventional onboard socket contact mounting and 80 mΩ low and stable contact resistance. Denmark base material with various plating options, including pure Springs, LEDA, cGold and “state of the art” Thebe.
-
product
Standard 3.00 (85.00) - 6.00 (170.00) Non Replaceable General Purpose Probe
G-S-R
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 30Test Center (mil): 125Test Center (mm): 3.18Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Overall Length (mil): 780Overall Length (mm): 19.81Rec. Mounting Hole Size (mil): 86Rec. Mounting Hole Size (mm): 2.18Recommended Drill Size: #44
