Showing results: 166 - 180 of 708 items found.
-
LS-16-R1-24SPLUS -
Lumistar Inc.
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
LS-16A-R1-24SPLUSC -
Lumistar Inc.
High Performance rack mount 1U x 12” deep switchable Multicouplers are available in multiple IN X OUT configurations, such as 1×8, dual 2×4, 1×4 and 1×6. The LS-16 product line covers 300 MHz to 6000 MHz. High output/output isolation and Ethernet / USB controllable gain adjustments for each channel are available as options.
-
MMC -
FM SYSTEMS, INC.
This connector panel is used to bring test signals from the rear side of a rack up to the front side of the rack so that measurements can be made without climbing in behind the rack.
-
Virginia Panel Corporation
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common test racks. Slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. Measure the rack depth between mounting rails and choose the slide kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
Virginia Panel Corporation
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
G12- 12 -
Virginia Panel Corporation
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. All slides are rated to support 180 lbs (81 kg) to accommodate even the largest fixtures. To order, measure rack depth between mounting rails. With this measurement choose the slide mounting kit that fits the rack. A rack extender kit is available for mounting to racks with recessed rails.
-
DAQA190A -
Keysight Technologies
Use this rack flange and filler panel with only one instrument mounted on either the left or the right side of the rack
-
H71002300 -
6TL Engineering
The 6TL23 is a bare rack for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 18U (580mm depth). The rack is ideal for sit-down operation, since there’s space for the operator’s legs under the fixture receiver.
-
Test Rack UTP 7033 RF for validation -
NOFFZ Computer Technik GmbH
Our basic test rack UTP 7033 (33 rack units) is intended for equipping with various products and therefore for various application areas.The rack shown here as an example is prepared with products and measurement instruments to test automotive devices with high channel count.
-
Y1130A -
Keysight Technologies
The Y1130A is used for forward or reverse rack mount. A rail kit is also required. For Keysight racks, order either a E3663AC rail kit for forward mount or a E3664AC rail kit for reverse mount. For non-Keysight racks, use a third party rail kit.
-
Y1130B -
Keysight Technologies
The Y1130B is used for forward or reverse rack mount. A rail kit is also required. For Keysight racks, order either a E3663AC rail kit for forward mount or a E3664AC rail kit for reverse mount. For non-Keysight racks, use a third party rail kit.
-
63-103-001 -
Pickering Interfaces Ltd.
This chassis mounting kit is designed for use with the 19-slot PXI chassis and the 18-slot LXI modular switching chassis, allowing installation into a standard 19" rack. When installed in a rack, a space of 1U should be allowed underneath the chassis for the cooling air intake, increasing the overall rack occupancy to 5U.
-
Y1216B -
Keysight Technologies
The Y1216B is a complete rack-mounting kit for the M9018B and M9019A PXIe chassis. It includes rack flanges, handles, and attachment hardware. Y1216B suspends the chassis in a Keysight rack using only 4U of rack space. It also recesses the chassis by 4 inches. This kit is not compatible with the Y1270A Front Panel Interfacing Kit.
-
34190A -
Keysight Technologies
The Keysight 34190A (5063-9240) rackmount kit is designed for use with only one instrument, mounted on either the left or the right side of the rack. The kit includes one rack flange and one half-rack width filler panel, 4 screws to attach the instrument, 4 rack screws with nuts and installation instructions in English.
-
Y1271A -
Keysight Technologies
The Y1271A is a complete rackmounting kit for the M9010A PXIe chassis. It includes rack flanges, handles, and attachment hardware. This kit allows you to mount the Keysight M9010A PXIe chassis flush with the front of the rack or to recess it up to 140 mm (5.5 inches) in 20 mm steps. Recessing the chassis allows for better cable management. The Y1217A rack rail kit is required and can be ordered separately. A minimum of 1U of rack space is required for ventilation above the chassis.