Showing results: 1366 - 1380 of 1792 items found.
-
CENTER 332 -
Center Technology Corp.
Air Velocity Measurement: m/s, km/hr, ft/min, MPH, Knots & Build In Temperature ºC / ºF, Humidity %RH, Air Velocity Compensation In Atmospheric Pressure, Air Flow Measure: CMM, CFM, Telescoping Hot Wire Probe
-
PCE Instruments
A sound level meter is a measuring instrument used to assess noise or sound levels by measuring sound pressure. Often referred to as a sound pressure level (SPL) meter, decibel (dB) meter, noise meter or noise dosimeter, asound level meter uses a microphone to capture sound. The sound is then evaluated within the sound level meter and acoustic measurement values are shown on the display of the sound level meter. The most common unit of acoustic measurement for sound is the decibel (dB); however, some sound level meter devices also determine the equivalent continuous sound level (Leq) and other acoustic parameters. With a portable sound level meter, industrial hygiene and workplace safety professionals can measure sound levels in multiple locations to ensure environmental conditions fall within recommended exposure limits (RELs). Some sound level meter devices can be permanently installed for continuous monitoring of sound levels at a work or job site. PCE sound level meter products are lightweight, easy-to-use and manufactured in accordance with the highest industrial standards.
-
PTS DII -
Bemco Inc.
PTS DII Gas Distribution Panels are similar to our PAO-DII Fluid Distribution Panels. They are designed to individually distribute, monitor, and protect one or more of your valuable products from the higher than required flow of a larger PTS, Portable Temperature Servo Conditioner or HPG, High Pressure Gas Conditioner. You can also use PTS-DII Gas Distribution panels with any other source of temperature controlled gas, including a competitor's air or gas source.
-
ESRF-HF Transmitter -
ES Systems
The ESRF-HF is a family of mass flow transmitters which enable fast and accurate measurements of gas flow over a wide dynamic range. Each transmitter integrates a MEMS flow sensor and readout electronics inside a housing with very small form factor made from stainless steel. The duty pressure of the flow transmitter is 11bar. All measurement data are fully calibrated, and temperature compensated on board, leading to a reduced temperature coefficient and high measurement accuracy.
-
HST-02 -
Jinan Leading Instruments Co., Ltd.
HST-02 Gradation heat sealing instrument candetermine five groups of seal parameters at one time including heat sealtemperature, time and pressure of plastic films, laminated films for flexible package, coating paper, and so on. Different melting point, heat stability,fluidness, and thickness of heat seal materials bring various heat sealproperties and different seal technique parameters as well. With thisinstrument users can get the best heat seal parameters accurately andefficiently.
-
Fluke Corporation
Fluke Multifunction Calibration Tools are designed to calibrate almost anything. These calibration tools source and measure almost all process parameters, and documenting versions even document the results The Fluke 754 does the work of several tools - sourcing, simulating and measuring pressure, temperature, and electrical signals in one compact, hand-held device. The Fluke 726, specifically designed for process industries, measures and sources almost all process parameters and can calibrate almost anything in the plant.
-
9565-P -
TSI Inc.
The portable, handheld VELOCICALC® Multi-Function Ventilation Meter 9565-P features a menu-driven user interface for easy operation in your local language. On-screen prompts and step-by-step instructions guide the user through instrument setup, operation, and field calibration. The 9565-P also features an ergonomic, overmolded case design with probe holder and a keypad lockout to prevent tampering during unattended use. The 9565-P model has a differential pressure sensor and does not include a probe.
-
Rotary Precision Instruments UK Ltd
Fully understanding components geometry prior to assembly is critical when faced with the ever growing environmental pressures and increasing fuel prices. The significantly more reliable measurement data collected by AccuScan™ enables rotor stacking software to accurately manipulate component parts, resulting in precisely aligned rotor assemblies. AccuScan™ has been independently verified and proven to offer our customers significant operational improvements over their traditional measurement methods.
-
FST-AM -
Foresight Electronics Co., Ltd.
A data logger, is an electronic instrument that records measurements at set intervals over a period of time. Depending on the particular data logger, measurements can include: air temperature, relative humidity, AC/DC current and voltage, differential pressure, time-of-use (lights, motors, etc.), light intensity, water temperature, water level, dissolved oxygen, soil moisture, rainfall, wind speed and direction, leaf wetness, pulse signals, room occupancy, plug load, and many more.
-
MKS Instruments
For cleaning CVD and ALD/ALE process chambers, the Paragon remote plasma source is designed for high gas dissociation rates (> 98%) of NF3 with gas flows up to 8 slm and pressures up to 10 Torr. This leading-edge performance translates into increased process throughput and repeatable process results. The Paragon design incorporates a proprietary plasma block design with a Plasma Electrolytic Oxidation coating for low particle, long block life that delivers lower cost of ownership.
-
TIRA GmbH
With the constantly growing competitive pressure in today`s market are quality and product innovation basic requirements for any company.For this purpose TIRA is developing accurate and high quality material testing machines and testing systems which are manufactured according to the national and international standards DIN 5122, EN ISO 7500-1, GOST. With our testing machines you can carry out the static testing of metals, parts, wood, building materials, glass, plastics, fibers, composites etc.
-
HST-01A -
Jinan Leading Instruments Co., Ltd.
HST-01A Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated films according to the requirement of relative standards. The seal parameters include heat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
James Bond Test ™ MK III -
James Instruments Inc.
The James Pull Off Adhesion/Bond Tester measures the pull force used to pull a 2? or 3? disc away from the material being tested. This pressure is displayed on a precision gauge and can be related directly to the strength of the adhesion to the surface being tested.
-
IEC60884 fig38 -
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 fig38 thermal compression test device for plug testingUsed to evaluate the pressure resistance of electrical accessories and wall mounted mounting boxes under heatStandard: GB2099.1-2008 Articles 24.19 and 25.4 and Figure 38, IEC60884-1 Figure 38, etc.
-
Karlan Digital Ltd.
We have range of options when it comes to weather stations. From a basic system for monitoring wind speed right up to a comprehensive set of sensors covering wind, temperature, barometric pressure, humidity, rainfall, solar radiation etc.
