-
product
PXI 2 Slot BRIC 66x8 2-pole (3 sub-cards)
40-562A-222-66X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays.
-
product
PXI Dual 32x4 Matrix 2-Pole Switching
40-534A-022
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109operations to give maximum switching confidence with long life and stable contact resistance. Larger matrices may be constructed by daisy chaining the common signals from multiple PXI modules.
-
product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
product
Voltage Variation Simulator
KES7400A
The KES7400A Series comes in a single cabinet that consists of a Signal Generator module (including an arbitrary pulse generator), which combines our power supply technology and EMC technology, and a high-speed bipolar power supply module. Many automotive electronic devices have long wire harnesses and inductive load characteristics, as do motors, or capacitive load characteristics with a large-capacity capacitor connected between the input and ground. In the case of these devices, general DC power supplies exceed the linear operation range, potentially making it impossible to obtain the desired waveform output.
-
product
human body vibration module
Human and Whole Body Vibration TestingThe human and whole-body vibration module tests and measures the effect of vibration on the human body. The extracted parameters allow the simple assessment of the injuries risk for workers, exposed to constant vibration. Our solution supports the whole-body and hand-arm vibration measurement are supported according to all relevant international standards - ISO 5349, ISO 8041, ISO 2631-1 and ISO 2631-5.
-
product
MTM-Bus Tester
PXIe-1149.5
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
product
PXI 2 Pole 18 way Mux with 2 Pole 18 way sen
40-658-002
This PXI multiplexer combines a 2-pole 18-way power distribution MUX with a second lower power 2-pole 18-way MUX in one convenient single slot PXI module.The module is ideal for power distribution where power and sense signals are required to be connected to an array of devices under test. This multiplexer is also convenient for making 4 wire low resistance measurements by supplying the resistor under test with high current through the power MUX and sensing the voltage drop through the sense MUX.
-
product
Tank & Vessel Cameras
Advanced Inspection Technologies Inc.
For remote viewing large areas, tanks, pressure vessels and pipes where limited access, radiation or safety makes inspection difficult. Each inspection camera system features a color camera module, high-intensity lighting, pan-and-tilt mechanism and industrial waterproof hosing for protection from extreme environments.
-
product
NI-9206, ±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module
779526-01
±10 V, 250 kS/s, 16-Bit, 32-Channel, 60 VDC Isolation C Series Voltage Input Module - The NI‑9206 performs differential analog input with four programmable input ranges. The module provides up to 600 VDC (400 VDC in Europe) channel‑to‑earth ground isolation, making the module ideal for accurately monitoring large fuel cell and battery stacks. By referencing the module common (COM) to the middle of the NI‑9206 bank, you can measure 16 consecutive cells and remain within 10 V of the module COM.
-
product
PXIe-8381, x8, MXI-Express Interface, PXI Remote Control Module
782362-01
PXIe, x8, MXI-Express Interface, PXI Remote Control Module—The PXIe‑8381 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCIe‑8381 through a copper, x1 MXI‑Express cable.
-
product
PXI-5154, 1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope
780319-03
1 GHz, 2 GS/s, 8-Bit, 256 MB/ch, PXI Oscilloscope—The PXI‑5154 is ideal for acquisition and characterization of fast, nanosecond-edge speeds. It is well-suited for automated test and data streaming applications in the consumer electronics, semiconductor, aerospace/defense, and life sciences industries. The PXI‑5154 also comes equipped with up to 256 MB of memory per channel to provide high, sustained sample rates over extended data capture windows. This digitizer, optimized for automated test, u...show more -
product
SMARC
ROM-5420 B1
ROM-5420 SAMRC v1.1 Module integrates ARM Cortex-A9 NXP i.MX6 series ultra low power SoC and I/O solution chips to be OS support ready. NXP i.MX6 supports 2D, 3D graphics acceleration, full HD 1080P video decoding and an HD 1080p video encoding hardware engine.
-
product
PXI 10 x 4 to 1 RF Multiplexer 1.8GHz 50 Ohm SMB Connectors
40-755-110
The 40-755-110 is a 50 Ohm high-density RF multiplexer (4 to 1) array with 10 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
product
Small Form Factor (40×70×12mm) CATV EDFA Module (Gain Block)
EATV5100-GM01
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5100 series is a low noise, high performance, high cost-effective EDFA module, which is specially designed for CATV system. EATV5100-GM01 is a gain module, using 40×70×12mm mini package, with single channel and narrow bandwidth standard version. A standard 6-pin or 12-pin electric connector provides simple electrical connection. The module adopts a high performance uncooled pump laser, the output optical power up to 19dBm.
-
product
Free Data Monitoring Software For EZ-Tap™, EZ-Pro™, And Versa-Tap™ Passive Tap Modules
Stratus Engineering's EZ-View™ data monitoring program controls communication and data collection parameters and displays time-tagged communication data and handshaking events in an easy-to-use scrolling display window.
-
product
PXI Precision Resistor Module 6-Channel, 3 to 11.4M
40-297-053
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Lens Driver Components
Analog Devices offers a range of lens driver solutions for camera modules in camera phones, camera enabled handsets, DSCs, consumer entertainment, and computer imaging. Lens drivers integrate drivers, waveform control, power management, signal processing, travel control, and more to provide the smallest, lowest power, most complete system solutions with the latest motor/actuator technologies.
-
product
SLED Source Driver
S-108
SLED Source & Driver slot module of FOTS system is an efficient module that can drive a stable high power broadband source and modulate a high power SLED to output a high bit rate optical signal. As a high power broadband SLED source, this module can drive the maximum output power of more than 14 dBm and has a stable wideband source characteristics of >90nm@-20dBm/nm. As a high current (400mA) modulation technique, it shows a high power and high bit rate digital signal of > 155 Mbps with > 13 dBm peak power.
-
product
SMARC® 2.1 Short Size Module With Intel® Core™ I3 Processors, Intel® Processors N Series And Intel® 7th Gen Atom® X7000E Processors
LEC-ALN
The ADLINK LEC-ALN is a SMARC module that supports up to 8 cores Intel® Core™ i3 (i3-N305, i3-N300) Processors, Intel® Processors N Series (N97, N50) and Intel® Atom® x7000E (x7425E, x7213E, x7211E) Processors (formerly Alder Lake-N) with integrated Intel® UHD graphics and high-speed interfaces. LEC-ALN modules support up 16GB LPDDR5 memory, up to 256GB eMMC storage (build option) and are also available with rugged operating temperature range and low power envelope, making them a perfect match for mission critical fanless edge computing applications that require safety and reliability at all times.
-
product
Solid State Relay I/O Module via Ethernet
2652 and 2653
upports 8 or 16 standard solid state relays (SSRs)Connects to Ethernet through 2601 hubInput SSRs are debouncedPWM mode for output SSRsBuilt-in support for safety interlock circuitsFinger-safe connectorsNetwork watchdog timerDIN rail mountableAPIs for Linux and Windows
-
product
12 D/A Outputs (±10 VDC or ±25 mA)
DA1
The DA1 module features 12 independent D/A output channels with a full-scale range of ±10 VDC at ± 25 mA (max). The DA1 provides either voltage or current control loop modes that are programmable for the particular application. The DA1 module also offers external trigger/synchronization signal (RS422/485) capability, which provides/accepts a trigger signal to/from other module(s).
-
product
PXI 8 Slot BRIC 132x8 1-Pole (6 sub-cards)
40-562A-121-132X8
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
product
High-Density Precision SMU (10 PA, 30 V)
PZ2131A
The Keysight PZ2131A is a high-channel density precision source / measure unit (SMU) having 5 channels per module and saving space for a wide range of applications requiring numerous precision power supplies. The narrow-pulse function and fast Digitizer Mode allow the PZ2131A to expand the conventional static DC measurements to emerging dynamic measurements. Its seamless current measurement ranging function eliminates the time it takes to change the range and expands the dynamic range to cover m...show more -
product
PXI/PXIe RF Matrix, 32x4, 150 MHz, 50 Ω, SMB, With Y Loop-thru
42-724-022-L
The 40-724-022-L (PXI) and 42-724-022-L (PXIe) are 32x4 RF matrix modules with y-axis loop-thru and are suitable for switching frequencies up to 150 MHz. Having a 50 Ω characteristic impedance and front panel SMB connectors, these modules provide a simple and scalable bidirectional matrix for RF and are intended for the easy construction of high performance switching systems.
-
product
Dual Channel Mini-SAS I/O FMC
FM550
Sundance Multiprocessor Technology Ltd.
The FM550 is an I/O module equipped with two external mini-SAS x4 connectors. I/O FMCs of this sort are typically used to provide inter-module connectivity via the front-panels of carrier cards fitted with similar interfaces, or fan-out to multiple external devices such as mini-SAS drives.
-
product
Robust Din-rail Fanless Embedded System With RISC-based (i.MX 6) Processor 4 COM, 2 CAN Bus And DIO
rBOX630
*Fanless design*RISC-based module (i.MX 6) processor*1 GB DDR3 SDRAM onboard*4 GB eMMC onboard*Completed industrial AP development software*Wide range DC power input (12 - 48V) with terminal block*Ready-to-run embedded Linux operating system*Wide temperature operation of -40°C ~ +70°C
-
product
PXI Express Board Virtex-5 ADC Module
SMT742
Sundance Multiprocessor Technology Ltd.
The SMT700 is one of the first of a new range of Sundance cards that includes a direct connection to SLB (Sundance Local Bus) compatible mezzanine card, without the need for a Sundance TIM. This enables a variety of cards to be added to a system, for example extra Ethernet ports, video in/out, High speed ADC / DAC etc. Data from these extra cards (along with data from the SMT700’s own inputs – up to 1Gb/s Ethernet, 2.5Gb/s optical links, and RSL links) can be processed via the Virtex 5, or by another linked card or module.
-
product
Switching Matrix Systems
VX Series
The VX Series of low-cost, versatile Switching Systems use a modular concept of Switch Modules,Display Modules and Control Modules which can be assembled into VX/256 Mainframes as Matrices,Multiplexers or Individual Relays.
-
product
Cable 100-Pin Micro-D Male To Unterminated, With Ferrules, 2m 2-56 UNC Screwlocks, Metal Shell
A100SMR-F-9B200
100-Pin Micro-D Male to Unterminated Cable Assembly With Ferrules, 2m Long With 2-56 UNC Screwlocks and Metal Backshell. Suitable for use with Pickering BRIC Modules.
-
product
PXI 4x3 20GHz Matrix
40-787-528-4X3
The 40-787 Microwave BRIC platform is designed to provide a solution for complex RF matrix applications. Using a common mechanical platform the module can be constructed to provide scalable non-blocking or blocking microwave matrix for frequencies to at least 20GHz. The standard configurations provide up to a 4x4 matrix. More complex matrix can be constructed by adding further switching functions and other devices inside the module.
