-
product
Rad Hard Load Switches
Renesas' radiation hardened load switches provide a simpler and smaller way to turn on and off your power rails in multi-rail power systems compared to a discrete FET. Load switches are also ideal for redundant power distribution, power sequencing and input-output protection of POL based power distribution systems.
-
product
Enhanced 16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT5
The DT5 module (the enhanced version) features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection. Additional features of the DT5 (Enhanced Version) are listed below.
-
product
Beam Load Cell
EST-70
Technopark Automation & Control
The EST-70 Shear Beam Load Cell is commonly used on platform, hopper weighing and pallet weighing applications. It is low cost and available in capacities from 500 kg to 2000 kg.
-
product
Temperature Input Device
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperatu...show more -
product
PXI 8 x SPDT Power Relay Module, 5A
40-155-001
40-150/151 modules have 8xDPST or 12xDPST power relays, suitable for switching inductive/capacitive loads up to 5A at 250VAC. 40-155/156 modules have 8xSPDT or 16xSPDT power relays and 40-157 is configured as 8xDPDT.
-
product
Motor Drive Test Systems
Drive and motor systems present unique challenges for test systems and Intepro combines regenerative active electronic loads to reduce the energy needed to do the tests as well as sophisticate instruments and supply voltages to test these demanding applications and provide meaningful results for the electrical and mechanical power parameters.
-
product
Emissions Dynamometers
MD-ASM-150-AWD (4×4)
The MD-ASM-150-AWD (4×4) tests both axles of the test vehicle under the same imposed load; while at the same time providing for front-to-rear axle speed synchronization. Front-to-back roller speed synchronization protects AWD center differentials, provides for a means to safely test 2WD vehicles with traction control, and allows for testing to be performed under real-world load conditions. The MD-ASM-150-AWD (4×4) accommodates wheelbases from 86 to 128 inches (218 – 325 cm) without moving parts.
-
product
Box Compression Testing Machine
Dongguan Kejian Instrument Co., Ltd.
Containers are subject to compressive forces when stacked and during transportation. It is vital to determine the compression strength of the box in order to make sure that the box will be able to resist the anticipated compressive forces and to determine the load that the box will be able to withstand during transit and storage.
-
product
Digital Battery Tester with Automatic Test
706
Controlled by microprocessor, simply activate the switch once and the #706 applies a precisely timed, 10 second load to the battery. The test results, “OK”,“WEAK” or ”BAD” are then displayed along with the test voltage, until the unit is disconnected. The #706 also tests charging voltage and relative starter current draw.
-
product
Capacitive Bank Load
Supreme Instrument Laboratories
Capacitive Bank Load Three phase suitable for operation on 415/440 volts three phase AC 50Hz housed in well ventilated sheet steel cabinet with bakelite front panel, complete with indicating lamps, voltmeter to indicate the input voltage and Ammeters to indicate, the load. ON/OFF switch, discharge switch etc. available in continuously variable type.
-
product
Digital Load Cell Simulator
Model EL41
Xiamen Elane Electronics Company, Ltd
Detection and debugging of all kinds of weighing instruments - "must have" for any scale service technician - fully RS232 controllable for testing of electronics for scale installation and manufacturing.
-
product
Dynamic Weighing System for Excavators
Loadtronic 3E
The load in the bucket is weighed during normal lifting cycle. The weighing can be started automatically or manually. The display will show the weight currently in the bucket, and the running total. Also, the number of buckets delivered is shown. The weighing system can be used as a tool toavoid over- and underloading of trucks. All loadings are stored in the main unit and can be retrieved either for printing a receipt or for transfer to PC (USB stick/ SMS). Databases of customers, materials etc. can be transferred between the office PC and the Loadtronic 3E system (using USB stick). The files can be viewed and edited in MS Office Excel or Notepad.
-
product
Manual Prober 100/150/200
Compatible with a wide range of needs for series evaluation and analysis with comfortable operability popular Always adopting a soft contact by adopting a shock absorber. It adopts a large platen and realizes mounting of a margin manipulator. Moreover, it is possible to adjust Z of the needle at once by moving the platen up and down. It is an ancient form that takes operability into account. It is easy to load / unload wafers.
-
product
Arbitrary Load Control For Modulation Distortion
S94570B
Extend the modulation distortion application by computing figure of merits such as EVM and ACPR for any desired load with arbitrary load control (ALC). Modulation distortion with ALC integrates the powerful capabilities of the PNA-X with an electromechanical tuner so a non-50 Ω load can be presented to the DUT and changes in device performance or sensitivity to varying load conditions can be accurately measured.
-
product
CEAST VisualMELT Software
VisualMELT Software is designed to control all the functions of the Modular Melt Flow Systems, from single-weight to multiple-weight tests. The software enables the user to manage all optional equipment, including the load cell, the automatic cutting device, and the motorized weight lifter. When working with a multi-weight tester, it is possible to set up and control single-weight or multi-weight tests, as well as define the order and number of weights to be applied.
-
product
Chassis Dynamometer Smoke Testers
A chassis dynamometer smoke tester (CDST) is used to test diesel emissions when the engine is under load. This is of course a much more realistic test than the commonly used free acceleration test. It is also better for the diesel engine.During a CDST test an automatic test cycle is performed, whereby the emission is measured at different engine loads. The monitor shows checks and actions to perform before the test, shows real-time measuring data and instructions for the driver during the test, and the end results after the test.
-
product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (m)
85562A
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight
-
product
Single 8x2 1-Pole 16 Amp PXI Power Matrix
40-552-002
The 40-552 range of 16 Amp PXI power matrix modules is available in four configurations with matrix sizes of 8x2 and 4x4 and the ability to expand the matrix size with the Y-Axis loop-thru connections: e.g. 8x4, 12x4, 16x4, etc. (with 4x4 matrices) or 16x2, 24x2, 32x2, etc. (with 8x2 matrices). This range is capable of switching up to 16 Amps and up to 300VDC/250VAC hot switching and 400VDC/250VAC cold switching. These PXI power matrix modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors, and solenoids.
-
product
Super MUTT Deluxe Edition Electrical Circuit Tester
#9008-DL
Innovative Products of America
The Super MUTT places a load on the trailer's electrical circuits to identify wiring problems while providing remote control operation over both air brakes and lights. Built to facilitate a one-man testing operation, the Super MUTT reduces guesswork and inspection time to prevent failures that lead to expensive road calls and citations. The remote control allows for repetitive air brake actuation at each axle to reveal developing problems often missed by normal testing procedures.
-
product
Controllable, Programmable Linear DC Source With Load
LAB / SLR
*Linear laboratory power supply*Integrated electronic load*Automatic range selection*Linear regulated DC source with automatic range selection*Built-in electronic load*Short-term peak load operation 240 or 480 watts*Protection against short circuit, overload and overtemperature*Double current / double voltage through "autoranging"*Fast control times approx. 250µ
-
product
Low Profile Solid State Relays, Utilizing MIL-PRF-28750 Test Methods
Series KD and LD
Your product description goes here.Series KD and LD solid-state relays utilize MIL-PRF-28750 test methods and are packaged in low-profile hermetically sealed cases. They feature fully floating power FET output technology. Options include short-circuit and current overload protection plus a status output line. Switch status returns the true status of the output switch and is optically isolated from the load.MSL 1KD & LD relays are controlled with 15mAdc/3.8Vdc (TTL), and 1mAdc/0.3Vdc (CMOS)....show more -
product
Industrial Single-Phase Relay With Antiparallel Thyristor Output
Series SHC
The SHC industrial, Single-Phase Relay with antiparallel thyristor output is the most widely used industrial SSR due to its multiple application possibilities. The relay can be used for resistive, inductive and capacitive loads offering both Zero-Cross and Random switching. The built-in varistor secures transient protection for the heavy industrial applications, and the LED indicates the status of the control input. The clip-on cover is securing touch protection to IP20 .
-
product
Portable Three Phase Phantom Load Power Source
SY2103
Hong Kong Songyang Industrial Ltd.
The new SY2103 series portable three phase phantom load stable power source, designed from new digital wave compound technology and according to International Standard, is newly intelligent equipment for energy meters. The equipment includes voltage/current source & standard meter, operated easily through front panel to preset directly all data of meter under test and test process.
-
product
High Accuracy AC Reference Source
515
Clarke-Hess Communications Research
The Model 515 High Accuracy AC Reference Generator fills a need for a relatively low cost and practical solution for supplying a reference excitation to typical LVDT and Synchro/Resolver transducers. The Model 515 has built-in load sensing which, in effect, yields "zero" output impedance and virtually eliminates the effects of fluctuating output loads. With up to 15 VA of output into loads with as much as 80 of phase shift, the Model 515 is ideally suited to driving inductive loads.
-
product
Force Sensor Elements
TE Connectivity (TE) enables OEMs to measure force using MEMS-based technology load cells. The same proprietary piezoresistive silicon strain gage technology used to measure pressure can also be configured into a reliable, low-cost package to measure force.
-
product
Arbitrary Waveform Generator Software
SourceXpress
PC-based software for arbitrary waveform generator control & emulation. From your PC, create waveforms using tools specifically targeted for your needs. From your PC, control one or many source instruments such as the AWG70000s. Control one or several AWG70000 instruments from one application. Load and play waveforms remotely. There is no new application to learn! SourceXpress™ has the same look and feel as the AWG70000 instruments.
-
product
Load Cells
The heart of each weighing system is a load cell. Load cells are mechanical components which act as force sensors by employing strain gages to provide an electrical output proportional to the applied force. Typically the electrical output is either analog (voltage or current) or digital. Load cells have specific mechanical packaging and sensing orientation to fit into electronic scales, and testing and monitoring systems. Load cells can be used for tension, compression, and/or shear measurement.
-
product
Portable Electricity Meter Testers
EE-120A-3S + EE-500V-3
The Phantom Load is able to generate three-phase voltages and currents with unprecedented stability and measurement accuracy. The amplitude and phase-shift of each current and voltage is individually adjustable. All types of electricity meters – mechanical or electronic, for active, reactive or apparent energy, single-phase or three-phase – can be tested with the Energy Standard. The following meter tests can be carried out with the EE Test System: Error Test, Register Test, No Load Test and Sta...show more -
product
Space Power Solutions
Teledyne e2v HiRel Electronics (HiRel) offers leading edge power solutions dedicated for high-reliability applications. The introduction of Galium Nitride (GaN) technology solutions enable high power density designs with four times less space requirements than traditional MOSFETs. The Teledyne HiRel Point-of-Load (POL) products combine multiple load capabilities, outstanding radiation performance with high levels of integration and easy to use features.
-
product
Unregulated Power Supply Models
Low-cost DC power suitable for driving loads such as lamps, relays and small motors is provided by these unregulated power supplies. All components are generously derated, assuring a long and trouble-free life; built-in fusing prevents damage due to prolonged overloading or short circuits. They are housed in extruded aluminum cases which can be mounted in any position.
