Showing results: 511 - 525 of 3419 items found.
-
Panasonic Industrial Devices Sales Company of America
Static charges on assembly lines can have devastating effects on sensitive workpieces. The solution is the new line of Panasonic Static Elimination Sensors. High-frequency AC ionizers offer extremely fast charge reduction by emitting a highly balanced ion stream directly to your parts before static discharge has a chance to damage them.
-
Wave Series -
JAI A/S
The Wave Series camera is a 2-sensor prism line scan camera capable of sensing Short Wave InfraRed (SWIR) light.The camera is based on Indium/Gallium /Arsenide (InGaAs) sensor technology and combined with JAI’s prism line scan technology, making it capable of delivering dual-band imaging in the SWIR light spectrum (900 – 1700 nm).
-
Rig Expert Ukraine Ltd.
Analog audio interface is a connection to transceiver audio output (external speaker connector or line output) and transceiver audio input (microphone connector or line input). Audio interface enables operating digital modes, recording and playing voice, as well as other useful functions (such as measuring levels of a signal from the air) by using a computer.
-
TOE 9261 -
Toellner Electronic Instrumente GmbH
Input voltage 60 V, Output current up to 100 A, Rise / fall time < 500 ns, Short-circuit-proof, Switchable discharge of load circuit, Interruption in supply and ground lines up to 100 A, Switchable buffering of input circuit, 4 signal line switches, Control with any signal generators (TTL level)
-
APCI-1516 -
TEAM SOLUTIONS, INC.
PCI interface to the 32-bit data bus? 8 isolated input channels, 24 V? 8 isolated output channels, 10 to 36 V,output current 500 mA? Timer-programmable watchdog for the reset of the outputs to ??? One ground line for all inputs and one ground line for all outputs? Outputs set to "0" at PowerOn/Reset
-
CITS880s -
Polar Instruments Inc
Finer geometries and thinner copper can present a challenge for fabricators measuring impedance on leading edge PCBs. The CITS880s answers that challenge with the introduction of Launch Point Extrapolation (LPE). LPE extrapolates the TDR response back to a point close to the start of the transmission line effectively allowing to users more accurately to measure the instantaneous or incident impedance of the line.
-
OP-SB89E -
LINEEYE Co., Ltd.
OP-SB89G is an expansion board for Ethernet LAN which is to be inserted into a slot of portable communication analyzer (LE-8200A/LE-8200). It has 4 LAN measurement ports and you can sniff 2 Ethernet lines at the same time by tap connection to capture packets on the 2 lines. It also can monitor input/output of a EtherCAT slave and measure the time delay cased by the slave.
-
East Coast DataCom, Inc.
The Modem Sharing Devices are designed to allow RS-232 DTE (terminal) devices to share Leased Line and Dial line Modems or DSU's. Data arriving at the Master Port is continually broadcast to all Subchannels. The attached terminal device that raises the RTS control signal is automatically given control of the MSD. Data rates of up to 128 Kbps are supported.
-
Dynamic Engineering
The Stand Alone Relay accepts a regular PC style power connector that powers two relays. Upon power failure, the relays disengage the two ethernet lines so as to not interrupt communication on the ethernet lines. A CPLD allows for pass through and bypass of Ethernet signals. 10/100 Ethernet compatible. The CPLD is controlled via user input.
-
SPA 1000 -
Gen3 Systems Limited
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
SPA1000 -
Gen3 systems
The SPA 1000 also introduces new process control capability by accurately measuring the suitability of the solder paste prior to its implementation on the production line. It achieves this by determining the "Open-Time" for the paste. It also performs the Slump Test and both of these methods provide a "Go/No Go" answer in less than 30 minutes to ensure minimum delay for the production line.
-
BD-IF400D -
Shanghai Baudcom Communication Device Co.,Ltd.
BD-IF400DOptical Fiber Identifier is an important tool for optical maintenance, which isused for nondestructive fiber identification project. Meanwhile it also hasVisual Fault Locator module with fault location function. Useingthe macro bending technology on line for nondestructive testing, BD-IF400DOptical Fiber Identifier can measure the signal direction and power and avoidmisoperation resulting in interrupted lines.
-
JW3306D -
Shanghai Joinwit optoelectronic Tech,co.,Ltd
JW3306D Optical Fiber Identifier is an important tool for optical maintenance, which is used for nondestructive fiber identification project. Meanwhile it also has Visual Fault Locator module with fault location function. Useing the macro bending technology on line for nondestructive testing, JW3306D can measure the signal direction and power and avoid misoperation resulting in interrupted lines.
-
LPA-2 50/100W -
Ametek Power Instruments
The LPA-2 is the next generation high-power amplifier for Power Line Carrier Communications and adds features and efficiency superior to all previous designs using the latest technology. It offers flexibility plus user-friendliness on its input and output such that it can be used with any power line carrier system. Two 50W units can be combined for a 100W output and to provide redundancy.
-
ATU's -
LBA Group, Inc
LBA medium wave AM Antenna Tuning Units (ATU) and Line Tuning Units (LTU) are impedance matching units designed to match the transmitter to the impedance of the transmission line or the antenna system. Our Antenna Tuning Units are available for both series-fed and {ln:Tunipole antenna systems} Tunipole™ antenna systems to powers in excess of 500 kW.