Limiters
-
Product
Power Limiter, 5 MHz to 6 GHz, Type-N
11930B
Power Limiter
The Keysight 11930B limiter provides input protection for a variety of RF and microwave instrumentation. Failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage. The Keysight 11930B provides the same protection to spectrum analyzers and sources. At even greater power levels, failure mode for limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Product
Gauge Type T Thermocouple Wire
W-TW-40P
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Oil and Grease Analyzer
LD-LOGA-A10
-
Oil and Grease analyzerLD-LOGA-A10is a tabletop analyzer with a sample testing range of0.12 mg/L to 840 mg/L. The unit displays and prints the sample spectra, position and wavenumber of the absorption peak. It features self-contained optical and electrical system withhigh degree integration. Testing data and spectrograms can be saved to hard disk forchecking and printing anytime Sensor signal processing uses lock-in amplifier circuitimproving the analyzer’s SNR and the minimum detection limit.
-
Product
RF Power Limiters
-
A protective electronic circuit that clamps or attenuates high-power Radio Frequency (RF) signals to prevent them from damaging sensitive components like Low Noise Amplifiers (LNAs) in receiver front-ends.
-
Product
Power Meter
8015 PM
-
Standard Electric Works Co., Ltd
● Determine the running cost of your appliances.● Measure voltage, current, frequency, watt, power factor, and greenhouse gas emissions.● Optical USB to RS-232 data transmission.● 2 Optical LEDs are built-in for data transfer.● Transferring and showing real-time data to a PC.● Make informed decisions when purchasing appliances and equipment.● Reduce your electricity bill.● Calculate electrical expenses by real, hour, month. ● Can make different kinds of plugs for different countries / areas, such as Type B, E, G, I plugs.....etc.● Data communication function.● Freely set upper and lower limit for V,A,W and alarm when measured value is out of limit.● Backlight function.
-
Product
Embedded System Supporting MXM Graphics Module with 8th/9th Generation Intel® Core™ i7/i5/i3 in LGA1151 Socket
DLAP-3000-CF Series
Embedded Platform
ADLINK provides an optimized, highly-available computing platform with expandability options, including the MXM cards. The DLAP-3000-CF series platforms support performance-hungry workloads (e.g., deep learning) with active cooling for applications requiring very high levels of computing in a limited space. DLAP-3000-CF Series features: - Smallest Embedded GPU Platform (3 liters) - Reliable MXM GPU Design with Low TDP - Scalable Graphics Processing Ranging from Pascal to Turing GPUs
-
Product
Leeb Hardness Testers
-
GAOTek proudly presents an extensive and wide range of Leeb hardness testers for sale to the United States, Canada and globally. A Leeb hardness tester is used mainly in the manufacturing industry to test the structural integrity of a metal object by applying a definite amount of force on the object. Structural integrity is crucial information as in some cases it is treated as a specification or standard that companies must meet in order to release a product. It may also be used to set a limitation or restriction for a specific device or item. Our testers are designed to ensure standards are met by providing users with a variety of features to make the process of testing and monitoring results efficient and convenient.
-
Product
Flexible MiniPCI Express 2-Way Splitter
SKU-059-2X
-
The Flexible MiniPCI Express 2-Way Splitter (Splitter) was designed to expand the modern motherboard (ATX, mini ATX, etc.) with a limited number of MiniPCI Express connectors. It allows you to connect up to two MiniPCI Express expansion add-in boards to the motherboard MiniPCI Express connector.The Splitter includes a MiniPCI Express Adapter board with a PCI Express flat cable (up to 2 boards), and MiniPCI Express host board.
-
Product
Insulated Electrical Tools
-
Most insulated tools have rubber or plastic on the handles. That’s not the same as offering protection from electric shock and limiting the possibility of arc faults due to short circuits. That’s what makes insulated electrical tools different.
-
Product
47~1200MHz FTTH CATV AGC Optical Receiver
H1222G
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai H1222G, the operating bandwidth of 47 ~ 1200MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver, Whether used in analog television or digital television. Due to the built-in optical AGC, at high optical power receiver, played limiting output, so H1222G in the received optical power over a large dynamic range of +2 dBm ~ -20dBm, and have excellent properties.
-
Product
NI-9478, 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-01
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
Vacuum Leak and Holiday Detectors
-
Electro-Technic Products, Inc.
Electro-Technic manufactures four handheld models (BD-10, BD-40, BD-50, BD-60) and a customizable automated model (Model BD-65) to suit specific customer applications and test materials. Our introductory BD-10 model is intented for light/intermittent use while our BD-50/BD-60 models are more suited for continous heavy duty use. Our model BD-40 has a limited voltage output suited for thin/sensitive linings.
-
Product
Hand-Held Sound Level and Vibration Measurement
-
Brüel & Kjær Sound & Vibration A/S
Our noise and vibration monitoring terminals and loggers are ideal for continuously monitoring real-time levels to demonstrate compliance with regulations, manage activities and limit environmental impact.
-
Product
Limiting Amplifiers
-
RF limiting amplifier PE15A6002 is rated at -40 dBm minimum power input and 10 maximum power input. Our limiting radio frequency amp is part of over 40,000 RF, microwave and millimeter wave components available from Pasternack. This coaxial limiting amplifier can ship worldwide the same day of the purchase as with our other available RF parts.
-
Product
Temperature Switch
T150D
-
The T150D Adjustable Stainless Steel Miniature Temperature Switches provide the end-user with a wide range of functionality without impacting durability. The T150 is designed for use up to 510°F but can withstand temperatures up to 800°F while still protecting the set point and life of the switch. The limit filled, saturated vapor sensor is in direct contact with the temperature-sensing outer shell producing fast response and accurate temperature control. The external setting scale provides full range adjustment and the external lock screw allows for easy adjustment of set point.
-
Product
Bipolar/FET/Diode Dual Head Production Test System
36XX
-
Two test stations on the 3600E and 3601E systems. Performs DC, AC, and pulsed tests. Excels at evaluating difficult to measure parameters on zeners, current limiters, varactor tuning diodes and darlingtons. 24 bin opto-isolated handler/prober interface. Parallel first-in first out computer to tester interface for maximum throughput. Parallel testing with a 3602E or 3603E allows shared test execution for extremely high throughput applications when interfaced to high speed handlers with multiple test sites.
-
Product
LED Burn-In Test
-
Burn-in system, based on LXI instrumentation, for concurrent testing of up to 80 DUTs in a climatic chamber. Devices to be tested include modern light emitting diodes and LED modules.The system consists of 2 control cabinets, each with 40 independent supply and measurement channels. Each channel can be configured individually via the operator software (current or voltage, including the relevant limit values). The software supports logging of current and voltage values for each DUT on all 80 channels with a sampling rate of <1s. Additionally, the software and system also support digital I/O channels, e. g. for controlling the climatic chamber. Inputs for connecting temperature sensors are also provided.
-
Product
Power Supply POWERLAB 305D
-
high precision current sources with variable voltage and current over the entire range . They can operate in different modes of stabilization voltage or current switched automatically with adjustable limit value of the load current at any point in the range.
-
Product
PXI 4 x 4 to 1 RF Multiplexer 1.8GHz 50 Ohm SMB Connectors
40-755-104
Multiplexer Module
The 40-755-104 is a 50 Ohm high-density RF multiplexer (4 to 1) array with 4 MUXs in a single PXI module. The 40-755 range is available with two connector options, an SMB connector that provides a frequency range of 1.8GHz and is available in single or dual PXI slots, or a multiway connector which limits the bandwidth to 1.3GHz but offers a high density solution occupying just one PXI slot. The RF switch design is identical in each case.
-
Product
Flexible MiniPCI Express to Two PCI Express Splitter
SKU-033-21
-
The Flexible MiniPCI Express to two PCI Express Splitter (Splitter) was designed to expand the modern motherboard (ATX, mini ATX, etc.) with a limited number of PCI Express connectors. It allows you to connect up to two x1 or x4 PCI Express add-in boards to the motherboard’s standard MiniPCI Express connector.
-
Product
X-ray Microscopy
ZEISS Xradia Ultra
-
Synchrotron X-ray nanotomography enables non-destructive 3D imaging at the nanoscale but you have to apply for very limited beamtime. What if you didn’t have to wait for synchrotron time anymore? Imagine if you had synchrotron capabilities in your own lab. With the ZEISS Xradia Ultra family, you have 3D non-destructive X-ray microscopes (XRM) at hand that deliver nano-scaled resolution with synchrotron-like quality. Choose between two models: both ZEISS Xradia 810 Ultra and ZEISS Xradia 800 Ultra are tailored to gain optimum image quality for your most frequently-used applications.
-
Product
Selective EMF Measuring Equipment
-
Selective measuring equipment for electromagnetic fields (EMF) for demonstrating safety and environmental compatibility. The devices analyze individual frequency ranges and field exposure levels accurately down to a single communications channel. They also calculate the sum and compare levels with current limit values.
-
Product
PXI High Density MUX BRIC, 16-Chan, 40-Pole
40-570-214
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
FMC Mezzanine Module, 4 or 8 Channel
NES-FMCSER
-
Sundance Multiprocessor Technology Ltd.
The FMC specification was developed to enable FMCs to be supported on a wide range of existing form factors including but not limited to, PCIe, VME, CompactPCI, VXS, VPX, VPX-REDI, AdvanceTCA and AMC. Up to three FMCs can be fitted on a 6U VPX carrier.
-
Product
Atomic Spectroscopy
-
For the past 40 years, we have provided products to the Atomic Spectroscopy industry that solve laboratory problems and improve the success of our OEM partners. These products include unique sample delivery solutions, sample preparation tools, autosamplers, and solutions to improve sample throughput and detection limitations, among others. In short, we strive to understand the markets our OEM partners serve in order to deliver products that meet their needs.
-
Product
Linear Polarization Resistance (LPR) Monitoring
-
The electrochemical technique, commonly referred to as Linear Polarization Resistance, is the only corrosion monitoring method that allows corrosion rates to be measured directly, in real time. Although limited to electrolytically conducting liquids, the response time and data quality of this technique make it clearly superior, where applicable, to all other forms of corrosion monitoring.
-
Product
IO-Link
-
The IO-Link® interface simplifies communication to smart sensors and actuators, combining signaling with power-over-cable technology. It has become one of the key devices as industrial automation systems are growing more interconnected and intelligent to accommodate demands for centralized control and optimized production. Analog Devices implements both device PHY and master PHY interfaces (COM1/COM2/COM3). Designing with harsh industrial environments in mind, the master 4-port IO-Link power and communications interface, as well as the IO-Link transceivers featuring Integrated Step-Down Regulators and LDO with ±60V cable interface protection provide the required ruggedness. Optimum EMC performance is achieved with adjustable current limit and slew rate transmitters. Automatic wake-up request (WURQ) generation and an output supply current boosting capability for device startup are also available. Additional components integrate a 300 mA step-down (buck) regulator and a 150 mA LDO to supply all the power required for internal electronics in an connected sensor or actuator.
-
Product
RF Safety Monitoring
MVG EME Guard XS 40GHz
-
EME Guard XS 40 GHz has been specifically designed to cover the new 5G millimeter wave bands. This RF safety tool is important for keeping those working close to RF emitters safer. It is easy to use, continuously scanning electromagnetic waves, and alerts the user when acceptable pre-selected limits have been exceeded.
-
Product
Solid State Relay
5200
-
The B/W 5200 Series solid state relays are offered in two basic types for use in a wide range of low and high sensitivity applications.Both 5200 solid state relays are designed to operate on either 115 or 230 volts AC at 50/60 hertz.Both models incorporate a low voltage sensing circuit.Furhtermore, both solid state relays are capable of performing control functions directly from electrodes suspended in a well or tank, the B/W Unifloat level sensing system, or various pilot devices such as pressure, flow and limit switches, thermostats and push buttons.
-
Product
Benchtop LCR Meter
1692
-
The GenRad 1692 LCR Meter is a sophisticated, microprocessor-controlled tester that brings new levels of flexibility, simplicity and accuracy to RLC measurement. It's testing automation at its best with a range of programmable test frequencies and test voltages, as well as automatic limit comparison, automatic parameter selection, remote programmability, automatic binning and automatic zeroing. The display facilitates visual acquisition of test data and eliminates costly guesswork and errors. The 1692 LCR Meter provides a powerful combination of features designed to maximize productivity in production testing applications.
