Limiters
-
product
PXI High Density MUX BRIC, 3-Chan, 160-Pole
40-570-013
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
product
Total Nitrogen Unit For TOC-L Series
TNM-L
Perform simultaneous TOC and TN measurements. *720 °C catalytic thermal decomposition/chemiluminescence methods are adopted for TN measurement. There is no interference from metallic ions or bromine in sea water.*Measurements over a wide range with a detection limit of 5 μg/L for TOC-LCH to an upper limit of 10,000 mg/L.
-
product
Digital Multiplexers
Advanced Science and Novel Technology, Co., Inc.
High speed broadband 4:1 Multiplexer (MUX)Exhibits low jitter and limited temperature variation over industrial temperature rangeDifferential CML I/O data and clock buffersQuarter-rate clock outputSingle +3.3V or -3.3V power supplyPower consumption: 960mWFabricated in SiGe for high performance, yield, and reliabilityCustom CQFP 44 pin package
-
product
Temperature Probe
*For surface and air/gas temperature measurement*Not suitable for liquids*Measurement range: -40°F to 399°F (-40°C to 204°C)*Probe length: 39.4 IN ±0.2IN (1 m ±5 mm)*Type K thermocouple*Lifetime Limited Warranty
-
product
PXI/PXIe RF Switch, 8xSP4T + 4xSP4T, 1.3 GHz, 50 Ω, Multiway Connectors
42-755A-902
The 40-755A-902 (PXI) and 42-755A-902 (PXIe) are high density RF switch modules configured as 8xSP4T and 4xSPDT. The range of modules is available in 50 Ω and 75 Ω variants with mixed SP4T & SPDT switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot. The connectors used are fully supported by the range of Pickering Interfaces connection solutions.
-
product
ECU & Bus Interface Modules
ES500
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
product
Precision Pulsed Current Sources
SpikeSafe Performance Series
SpikeSafe™ Performance Series Current Sources supply DC and precision continuous or single pulse current for light measurement and other applications. With sustained output power and no duty cycle limitations, Performance Series Current Sources support a broad range of applications.
-
product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
product
Custom Systems
With our custom VNA your ATE works as one software system running on a single computer. We can customize the analyzer module to fit in your system, provide extra frequency range coverage as compared to our standard VNA models should you need it in your specific application or characterize the expected performance outside the frequency limits of our standard VNAs.
-
product
Humidity Chambers
FW Series
The Bemco FW Series of mechanically cooled Glass Door Humidity Chambers have a a temperature range of -28 C to +177 C (-20 F to 350 F) or -73 C to +177 C (-100 F to 350 F) and a humidity range of up to 5% RH to 95% RH.. These chambers feature direct dry air injection and direct humidity sensors. They operate without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allow operation at 20% RH at 5 C and 50% RH at -14 C!
-
product
Dual Channel, Low-Noise DC Bias Card
PI-41701
The PI-41701 is a dual channel bipolar DC Bias supply that can provide an output current up to 100 mA per channel. The output voltage ranges from –8 V to +8 V and features programmable current limits with LED indicators and software interrupt to show/alert the user if the channel is in current limit. This card has special filter circuitry to reduce the output noise for those applications that require a low noise bias output.
-
product
X-ray Fluorescence Measuring System
FISCHERSCOPE X-RAY/XDV-SDD
Premium model for universal use for the inspection of very thin or complex layers up to RoHS screening at very low detection limits.
-
product
Multi-Channel Clock Generator
XCLK1
Curtiss-Wright Defense Solutions
High-speed analog IO acquisition systems need a high quality master reference sample clock.Accurate synchronization in the 100MHz and up frequency domains is not easy and it’s a critical performance limiting factor if not done well. The XCLK1 multi-channel clock generator solves these problems.
-
product
EMR Testing
It is widely accepted that exposure of the human body to high levels of Electromagnetic Radiation (EMR), Electromagnetic Energy (EME) or Electromagnetic Fields (EMF) may lead to adverse health effects. To ensure the protection of personnel in the workplace and to protect members of the general public, it is essential that the EMR levels comply with relevant exposure limits set by regulators in each country.
-
product
Non-Contact Forehead IR Thermometer
Extech IR200
The IR200 is ideal for quickly screening individuals for elevated skin temperature. This infrared thermometer has a non-contact design that eliminates the need for replacement probe covers and other supplies. The IR200 is accurate to 0.3°C (0.5°F) with 0.1°C/°F resolution when measuring skin temperatures between 32.0°C to 42.5°C (89.6°F to 108.5°F). Adjustable alarm alerts user visually and audibly when temperature exceeds programmed limit. Optimum measurement distance of 5 to 15 cm (1.9 to 5.9 in). Move the Body/Surface function switch to the Surface position for non-contact surface temperature measurements from 0°C to 60°C (32°F to 140°F). With a fast response of just 0.5 seconds, users can simply press the trigger and read temperature on the large backlit LCD display. Memory stores up to 32 readings for easy recall. Comes complete with 2 AA (1.5V) batteries and pouch.
-
product
1000W Ferroresonant Power Supply
Series PRR
Kepco's PRR are 1000 Watt rack mounted laboratory systems power supplies that offer the low cost and very high dependability of ferroresonant voltage stabilization.The ferroresonant stabilizing technique provides extraordinary isolation from a wide variety of source noise. It is inherently short-circuit proof and cannot expose delicate loads to overvoltage hazards. Hence no crowbar, fuses, or bounding circuits are needed. Ferroresonant power supplies use no noise-producing switches or oscillators. Voltage setting is independent of delicate control settings or diode references and requires no comparators, references, or limiters. Efficiency is 70-80%.
-
product
RF Safety Monitoring
MVG EME Guard XS 6GHz
The EME Guard XS is an RF measuring device to alert workers near RF emitters for protection of climbers and other RF-exposed workers. It continuously scans for electromagnetic waves and, via its built-in alarm and visual system, alerts users whenever the acceptable pre-selected limits have been exceeded. This RF Safety PPE is extremely easy to use and supports a safer working environment in the areas of installation and maintenance.
-
product
Portable Dynamometers
Perfect solution for shops with limited space that would like to have a dyno that they can move out of the way when it is not being used. The low profile design and relatively small footprint of the MD-150 makes it ideal for these situations. Mustang has integrated a lift jack like you would see on a standard pallet jack into the frame of the MD-150 and equipped the opposite side of the dyno with retractable heavy-duty casters to make moving the dyno around the shop easy for a single person. Simply roll the dyno into place, plug it in and attach the ramps and you are ready to perform performance tuning and diagnostics testing in minutes.
-
product
Shock Reactance
ICR260 330
Lifasa - International Capacitors, SA
Shock reactors are necessary to limit the transient currents that occur in the connection of the capacitors.
-
product
FCC Part 15 Testing & Certification
FCC Part 15 is the section of Title 47 of the Code of Federal Regulations that sets limitations on the amount of electromagnetic interference allowed from digital and electronic devices. FCC Part 15 also covers technical specifications, administrative requirements and other conditions relating to the marketing of FCC Part 15 devices.
-
product
CSvideo | CTvideo | CSvision Series Infrared Thermometer
The video pyrometer series optris CSvideo/CTvideo and the new innovative ratio pyrometer CSvision allow a parallel use of video and crosshair laser aiming for an optimal measuring field adjustment even in processes with limited access. They reliably measure temperatures of metals or ceramics and, due to their short measuring wavelength, reduces measuring errors of surfaces with low or unknown emissivities. The high quality video sighting can show its full advantage together with the software CompactPlus Connect or the IRmobile App on your cell phone with state-of-the-art zoom and image rotation features. The adjustable focus, motorized on CSvision, allows an optimal adaptation to different application and installation demands. As CSvision can measure objects up to 3000 °C a unique two-step brightness reduction filter (BRF) is giving the user a tremendous advantage when aiming on hot and extremely bright objects.
-
product
Miniature Axial Extensometers
Model 3442
Jinan Testing Equipment IE Corporation
Weighing as little as 8 grams, these miniature extensometers are designed to have very low operating force with minimal specimen influence. All use an improved version of Epsilon’s dual flexure design which makes them very rugged for their size. With a module height of 15.2 mm (0.6 inches), they will fit in the limited space between grips that is typical with small test samples. Gauge lengths can be as short as 3 mm or as long as 50 mm. A newly designed gage setting pin and assembly allows the gauge length to be set accurately and repeatably to ASTM and ISO requirements for all gauge lengths. Reengineered quick attach wire forms provide simple and secure specimen attachment. Wire forms for round and flat specimens are included, as well as flat, 3-point, and vee knife edges. The wire forms may be removed to enable mounting using elastic bands or springs. A tethering attachment point provides fall protection and enables counterbalancing of the extensometer’s weight when testing delicate specimens.Model 3442 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller and Epsilon will equip the extensometer with a compatible connector wired to plug directly into the controller. For systems lacking the required electronics, Epsilon can provide a variety of solutions for signal conditioning and connection to data acquisition systems, chart recorders, or other equipment.
-
product
Tri-phase High Power Programmable AC Power Source
APS50000
Advanced direct digital frequency sythesizer(DDS) waveform generation technology, high frequency stability, good continutyMeasurement precision is high, suitable for current half-sinusoid and its similar waveforms with DC component measurementProvide embedded intelligent PC monitoring systemAdjustable output voltage from 0 to 150V, 0 to 300V, step distance 0.1VOutput frequency 45-120Hz(40-500Hz optional), step distance 0.1 HzOutput current limiting functionWith 9 sets of memory, you can store commonly used parameters for easy invocation when using themWith RS232C communication interface 【IEEE488.0(GPIB)optional】, instruction execution times is less than 10mSProtechtion mode: over voltage, over current, overload, short circuit,current limit, ectProvide RMS voltage, RMS current, active power, frequency, power factor, ectFor 100% load removal, voltage stabilizing reaction time within 20ms, strong overload capacity, instantaneouscurrent can with stand 3 times of rated current
-
product
RF Frontends
Becker Nachrichtentechnik GmbH
Software-Defined Radio (SDR) is an attractive approach for mobile communication architectures in the development and evaluation phase for a rapid prototyping on a flexible platform. SDRs support a wide frequency range. However, for practical use in the field the HF properties are insufficient. The transmit power is limited to a 2-digit mW value. Dedicated filters are required for an effective suppression of out-of-band signals and to improve the noise figure of the receiver chain. Extending SDRs with application-specific RF-frontends achieves optimal RF performance in the field.
-
product
Temperature Switch
T150D
The T150D Adjustable Stainless Steel Miniature Temperature Switches provide the end-user with a wide range of functionality without impacting durability. The T150 is designed for use up to 510°F but can withstand temperatures up to 800°F while still protecting the set point and life of the switch. The limit filled, saturated vapor sensor is in direct contact with the temperature-sensing outer shell producing fast response and accurate temperature control. The external setting scale provides full range adjustment and the external lock screw allows for easy adjustment of set point.
-
product
Switch Matrices
Mercury System’s family of rugged, custom-designed switch matrices are available in rigid PCB construction, module-based packages, or rack-mount solutions. Each switch matrix is a highly integrated, SWaP-optimized assembly consisting of an assortment of switches, filters, amplifiers, attenuators, limiters, and drivers. The result is high speed channel selection, high isolation, high linearity, and low insertion loss.
-
product
PathWave BenchVue USB Modular SMU Pro
BV0023B
The PathWave BenchVue USB modular SMU pro software configures voltage and current source, range and limit for each SMU channel and log unrestricted data.
-
product
Engineered Solutions
New built or retro-fit, Mors Smitt delivers a perfect, competitive and on time solution for any onboard challenge of space limitations and / or technical requirements. No matter the size or quantities. We understand the need for integrated specialised and optimised electrical solutions when (spare) parts are no longer available or improvement in e.g. energy efficiency or reduction of weight and space is required.
-
product
Ultraminiature Microphone
MB-2200M10
MB-2200M10 is an ultra compact and lightweight microphone that enables measurement in narrow spaces, where have been difficult to install, without giving influence to the sound field.Its compact and lightweight features make you possible to perform measurements in a limited space, such as multi-point measurement, and measurement near the sound source. As CCLD type, the MB-2200M10 can be connected to Ono Sokki’s FFT Analyzer or CCLD supported devices.
-
product
FactoryTalk Analytics
Pavilion8
Complex industrial processes make it challenging to be both market driven and sustain profitable operations. Manufacturers must adjust their production methodology to introduce a greater variety of higher value products and shorter production runs. They need to produce more, run efficiently and improve product quality to the limits of available equipment. For this, they must ensure maximum uptime and more efficient transitions with less waste. In addition, manufacturers are facing stronger public demand to reduce their environmental impact and operate within regulated emissions limits.





























