Filter Results By:
Products
Applications
Manufacturers
Lighting
is used to illuminate.
See Also: Light, Illumination, Lightning, Lightwave, Daylight, Streetlight, Light Sources, DMX
- LBA Group, Inc
product
Static & Lighting Chokes
Lighting chokes are used to pass tower lighting voltages across the base insulator of a series-fed tower without appreciably altering the tower impedance. LBA TC-300 general purpose tower lighting chokes are provided for three wire 110/220 VAC circuits. Maximum current is 25 amps. These chokes are rated for peak base voltages to 10,000 volts, and present a typical reactance of +j5000 ohms at 530 kHz. Bypass capacitors are provided on each winding.
-
product
Trailer Lighting System Tester
Scanner
A Scanner Trailer Lighting System Tester makes the job a lot faster and easier since it powers your trailer's lighting circuits in sequence. You check the operation of all lighting functions in a single walk-around instead of two or three.
-
-
product
Automated Optical Inspection (AOI)
TR7700 SIII
TR7700 SIII is the newest generation of TRI's AOI solutions, delivering precise multi-phase inspection at full speed. By combining an ultra-fast camera, intelligent auto conveyor, and new GUI, the TR7700 SIII offers a powerful and easy to use AOI solution with fast programming, optimized board loading, production line integration and support for offline programming. TRI's new color algorithm combined with multiple lighting phases increase defect coverage and help deliver highly accurate inspection results with a minimum of false calls.
-
product
Cable Sheath Testing and Fault Location System
Shirla
BAUR Prüf- und Messtechnik GmbH
Cable fault location with the BAUR shirla. Shirla the fault location system is used for cable and cable sheath testing as well as for pre-location and pinpointing of cable faults. The pre-location based on the measuring bridge principle according to Murray and Glaser that is designed especially for power cables, also enables pre-location for control and lighting cables. Null balance and evaluation take place automatically.* Cable and cable sheath testing up to 10 kVC* Resistance measurement* Cable and cable sheath fault pre-location with precision measuring bridge* Adjustable cable sections that can be defined with length, conductor cross-section and material respectively and can be considered in the distance calculation
-
product
Endpoint / Chamber Health Monitor based on Optical Emission Spectroscopy and MWL Interferometry
EV 2.0 Series
To address new requirements in Semiconductor, lighting devices, automotive components, flat panels, MEMS sensors, memory chips, and logic electronics processed in the industry using dry etch, cleaning and (PE)CVD, HORIBA has introduced a unique generation of sensor dedicated to Advanced Endpoint Control, Fault Detection and Chamber Health Monitoring.
-
product
Ethernet DMX Node With Up To 8 DMX Ports
XND-4
XND-4 and XND-8 nodes are user friendly sACN and Art-Net to DMX converter supporting the distribution of up to eight universes of DMX via individually optically isolated DMX outputs. Since most major lighting consoles are capable of transmitting Art-Net data, an XND node is all you need in order to take advantage of your console’s networking capability, allowing you to transmit a vast number of universes over one single network cable. In some cases, users may profit from already existing networking infrastructure.
-
product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron®, Intel® Q170, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS962-512-PoE
The IPC962-512-PoE meets the increasing requirements for maximum quality and flexibility in modern production plants. It features flexible expansion capacity, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control. This machine vision controller is powered by the LGA1151 socket 7th/6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® Q170 chipset. The IPS962-512-PoE comes with a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The real-time vision system PS962-512-PoE enables a fast and high accurate inspection to ensure that the desired quality is achieved with no manufacturing defects. It supports four IEEE802.3at PoE LAN ports and four USB 3.0 ports for connection with industrial cameras. Operating over a wide temperature range from -10°C to +55°C, the IPS962-512-PoE provides reliable and stable performance within severe environments. Its easy setup and compact design are ideal for space constrained environments. Moreover, one PCIe x16 and one PCIe x4 expansion slots allow quick installation of I/O cards and graphics cards. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
product
PPID-2000 Photosynthetic Photon Intensity Distribution Test Unit
Hangzhou Everfine Photo-E-Info Co., LTD
It is mainly used for testing plant lighting products. With the EVERFINE GO-R5000 goniophotometer system, it can realize the measurement of plant photosynthetic photon intensity distribution (μmol/s/sr) in the whole space. In addition, the device can also realize the test of photosynthetic photon flux, far red light photon flux, photosynthetic radiation efficiency and other parameters, referring to DLC, ASABE, DIN, GB, CQC and CSA related international plant lighting standards .
-
product
Film Capacitors
Panasonic Industrial Devices Sales Company of America
Low ESR. Low Dissipation Factors. No Shock Noise. Panasonic Surface Mount Film Capacitors offer stable capacitance and temperature characteristics, tight tolerances, low ESR, low dissipation factors, no shock noise, no piezoelectric effect and no audible noise. Surface Mount Film Capacitor applications include DC blocking and filtering, PLL, audio, DC/DC converter and back lighting.
-
product
Three Loop Antenna
VVLA-30M
The three loop antenna VVLA-30M is a standard measurement antenna according to CISPR15-2005/GB17743-2007 standard
, it can work with LISUN EMI-9KA / EMI- 9KB EMI Receiver System for EUT magnetic field radiation measurement between X, Y and Z planes. The antenna measurement is accurate, switch conveniently and it can completely replace imported products. -
product
Compact AC/DC Auto Ranging Clamp Meter
410002
The small bodies and jaws fit perfectly in your hand and into tight places. Meter controls are positioned so that current measurements can be done with one hand. A large backlit display is easy to see, and the handy display hold function keeps measurements fixed on the display. Measures starting current for motors, lighting, etc.
-
product
Diffuse Reflectance Sphere
DRS100
Mobile displays are used in a variety of ambient lighting environments. The evaluation of mobile displays under diffuse illumination conditions is critical to the understanding of display performance in the real world, as mobile displays are used in a wide range of ambient lighting environments. The DRS100 is purpose-made to completely characterize the diffuse reflectance properties of mobile displays, providing uniform hemispherical illumination.
-
product
Volt Tester
PPTVM01
The DC Voltage Tester is an easy-to-use tool that can quickly test for voltage. Perfect for testing batteries, lighting systems, trailer connections, and more. This voltage tester is self-powered with a 210 cm cable. LCD displays voltage readings from 5 volts to 35 volts.
-
product
LFA-3000 Light Flicker Analyzer
Hangzhou Everfine Photo-E-Info Co., LTD
LFA-3000 can simulate flickering measurement and analysis under various voltage fluctuation conditions, and the system has built-in standard voltage waveform database, one operation can complete the test and analysis of IEC 61547-1, convenient and fast. Meet the lighting product design, quality inspection and application of flickering test analysis needs.
-
product
Light Meters
Our light meters are designed for simple and accurate results in an industrial setting. Whether you are checking work spaces, parking lots, or baseball fields for safe levels of lighting or measuring for testing design compliance, a light meter from Sper Scientific will get the job done. Obtain precise UV, FC or Lux measurements, in multiple light measurement ranges. These light meters are designed for use in work spaces, labs, schools, outdoor studies, optics, home inspections, and many others. In addition, you may use these meters to check compliance with ANSI/NFPA 101 (standards for emergency & exit lighting).
-
product
Multispectral PTZ Thermal Camera
Saros DM-Series
The FLIR Saros DM-Series introduces eight new VGA and QVGA resolution options to FLIR’s multi-sensor security lineup. Capable of capturing video in complete darkness, bright sunlight, and through smoke, dust, or light fog, the DM-Series provides superior perimeter protection in the toughest lighting and environmental conditions. A built-in 4K visible light camera operates alongside the thermal sensor to capture minute details in low light conditions. The DM-Series also integrates with the FLIR United Video Management System (UVMS), as well as other ONVIF-compliant video management systems. This gives users complete control over the all new dual-sensor viewing mode, alarm functions, and fully programmable preset tour.
-
product
Sapphire 3D Microscope
WDI-2000
The Sapphire 3D Microscope: HS-WDI-2000 was designed with high quality lighting parts and a good optical system design,can get a very clear image.with the digital camera,it can provide the image in time, widely used in LED,Solar,SEMI…
-
product
Real Scene Lighting
LightSTUDIO
Image Engineering GmbH & Co. KG
Test charts are used to test digital cameras and to perform objective measurements. But there are certain aspects in testing a camera that require a real scene. One of these aspects is the correct white balancing for different types of illuminants. Another aspect might be the determination of the visual loss of detail due to noise reduction or the amount of noise in an image.
-
product
Seat Actuation Systems
Extensive solutions for seating cabin interiors including motion and lighting controllers, linear and rotary actuators, power supplies, passenger interfaces, custom harnesses, sensors, pneumatic units, and bladders.
-
product
High Precision Glow Wire Tester
CX-Z17
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is desinged according to IEC60695-2-1, IEC60695-2-13, UL746A, IEC829, DIN695 and VDE0471 etc. standards.The IEC60695-2-1 CX-Z17 High Precision Glow Wire Tester is suitable for resistance to abnormal heat and fire test on lighting lamps, electronic products and household appliances.
-
product
PHOTO-2000AH Automatic Horizontal Photometer
Hangzhou Everfine Photo-E-Info Co., LTD
PHOTO-2000AH is used to test the horizontal illuminance of sloping surfaces. It has the advantages of small size, easy operation, high precision, wide range and low power consumption, and is especially suitable for the lighting effect evaluation of sports venues, industrial sites, commercial lighting and other occasions.
-
product
Smart Lighting Management
Single-chip solutions enable IoT connectivity and precise control of smart lights and replacement lamps.
-
product
Blade Socket Tester
RV 7
Blade Socket Tester offers a fast, easy way to isolate a lighting problem to the trailer or towing vehicle. A must have for anyone who deals with hitch and lighting hookup installations, it tests the output of towing vehicle's RV 7-blade lighting socket.
-
product
USB 3.0 Color Autofocus Camera
DFK AFU420-L62
The Imaging Source, international manufacturer of machine vision cameras and software for industrial imaging, has just announced the introduction of a newly developed 42 megapixel industrial camera featuring a USB 3.0 interface. Based on the newest high-resolution CMOS technology, the camera features exceptional image and color quality as well as automatic color correction. Via the integrated HDR mode, the camera captures image details previously unobtainable using other cameras - even under the most challenging lighting conditions. At 42 megapixel resolution, the camera achieves an image rate of 7 frames per second; 110 frames per second can be captured at 2 megapixels (full HD). Available as either C/CS mount or with integrated autofocus optics, the 42 megapixel camera is the perfect solution for a wide variety of applications. With their light, robust and compact housing (36x36x26mm), they are ideal for applications where space limitations are a factor. As additional features, a free 1- and 2D barcode SDK as well as software for on-screen measurement and image acquisition are also included.
-
product
Testing Aircraft and Helicopters
Sun Test Systems develops and manufactures mobile test equipment for commercial and military aircraft and helicopters.The product range consists of:A complete line of hydraulic test equipment for every helicopter or aircraft size. This equipment is able to fully clean and regenerate the hydraulic oil of the airplane from air, water and particles during hydraulic test activities. By integrating these two functions our equipment saves maintenance time and reduces repair work because of less leakages of the hydraulic system etc.The multifunctional product line which combines a number of GSE functions, such as hydraulics, electricity, air, nitrogen, lighting, in one single unit.The other product lines with among other things a dye mix trolley for display teams and washing equipment for fuselages and engine cores.Our close cooperation with the German and British military forms the basis for the extensive product range. The products are designed and built to combine heavy use by the military with severe conditions encountered in desert areas or extreme cold. They have built up an extensive ‘proven track record’.
-
product
Battery Capacity Analyzer
600B
The 600B Battery Capacity Analyzer addresses the need to test and maintain sealed lead acid (SLA) batteries used in backup power UPS, emergency lighting, fire alarms, security systems, and many other electrical systems. By quickly characterizing a battery's response to a load resistance, the meter displays the remaining battery capacity as an indicator of the battery's health.
-
product
Smart Camera
P-Series
The P-Series is an ultra-compact cost effective smart camera offering advanced machine vision functionalities in a fully embedded stand-alone device. The P-Series is available in two different resolutions: VGA (P10) and 1.3MP (P15). Lenses and illuminators are fully interchangeable and can be mounted and replaced by the user. Five focal lengths and seven lighting options result in 70 different combinations delivering outstanding installation flexibility while offering superior image acquisition capabilities.
-
product
Vision System With LGA1151 Socket 7th/6th Gen Intel® Core™ I7/i5/i3 & Celeron® Processor, Intel® H110, 4 PoE, 4 USB 3.0, And Real-time Vision I/O
IPS960-511-PoE
Featuring a multi-core CPU, IP40-rated rugged design, camera communication interfaces, real-time vision-specific I/O with microsecond-scale and LED lighting control, the IPS960-511-PoE provides an all-in-one solution that addresses the needs across various machine vision platforms and automatic inspection cases. The IPS960-511-PoE is powered by the LGA1151 socket the 7th & 6th generation Intel® Core™ (codename: Kaby Lake/Skylake) and Celeron® processors (up to 65W) with the Intel® H110 chipset. The intelligent vision system comes with dual DDR4-2133/2400 un-buffered SO-DIMM sockets for up to 32GB of system memory as well as supports rich camera interfaces for connecting industrial cameras, including four IEEE802.3at PoE LAN ports and four USB 3.0 ports. Its vision I/O integrates a full range of isolated I/O interfaces and real-time controls essential to machine vision applications, including trigger input, LED lighting controller, camera trigger, as well as an encoder input for conveyor tracking. The IPS960-511-PoE also supports lighting dimming control to identify object characteristics for different inspection. Two easy-swappable 2.5" HDDs are available for extensive storage needs.
-
product
Environmental Chambers
Whatever your application, from an environmental chamber for small components to an extensive array for a complete automobile or aircraft test, EYE / Iwasaki has the experience to provide a solar lighting system customized for your requirements. Our systems are designed to be flexible and deliver the optimum solar simulation solution. We do not force-fit a "standard" system to attempt to meet your needs.
-
product
Climate Test Chambers
Infinity Machine International Inc.
Climate Test Chambers by Infinity Machine International Inc. - for applications such as dust proof climate test chamber for lighting, dust climate chamber for lab, and more.
