Showing product results. 1411 - 1425 of 2220 products found.
-
CO15 - Extech Instruments Corporation
Check CO levels up to 999ppm with the push of a button using Model CO15. An audible alarm indicator will continuously beep starting at 25ppm (preset warning level - value can be adjusted) and the display will flash until the CO level goes down to normal range. A backlight on the display can be used for low light areas. The meter comes complete with batteries, wrist strap, and pouch.
-
Nüvü Cameras
CCCP is the technology behind Nüvü Camēras’ extraordinary sensitivity in low light imaging. The patented controller generates significantly less clock-induced charges (CIC) than any other CCD controller during charge transfer throughout the EMCCD (down to an average below 0.001 ē/pixel/frame), therefore allowing for greater EM gain to ultimately attain sub-electron readout noise.
-
Colorette 3B - Probat Burns
Achieve consistent results by monitoring and precisely controlling the degree of roasting with the Colorette 3B color-measuring unit. Unaffected by ambient light, this portable and extremely accurate device uses infrared and red LEDs to measure the exact color of ground coffee samples. It then displays the measurement and automatically prints a complete record, including the color value, sample number, roaster number and batch date / time.
-
EC-501A & EC-501A(G) - Automation Products, Inc.
Dynatrol® EC-501A and EC-501A(G) Control Unit combines with the DJ and G Series Dynatrol® Level Detectors, including Sealed and Suspended units. Within the Control Units, a SPDT relay is operated from the On/Off signal of the Dynatrol® Level Detector. Simply actuate process control equipment, level alarms or indicator lights from the contacts of this control unit.
-
OCC-50 - ShinewayTech
OCC-50 Handheld CWDM Optical Channel Checker is specially designed for CWDM installation, maintenance and troubleshooting, which is able to measure and monitor power values of up to 18 CWDM channels. OCC-50 can replace high-cost spectrometers and conduct quick and reliable measurements in all environments. Thanks for its light, compact and sturdy design, OCC-50 is the ideal tool for CWDM installation and maintenance technicians.
-
Bentham Instruments Ltd
Our detection electronics portfolio comprises all the detection electronics elements required for the operation and automation of a high quality light measurement system, including photo-detector signal recovery and digitisation (with fully programmable DC, AC and lock-in amplifiers having current/ voltage inputs), high voltage supply, optical chopper control, detector thermoelectric cooler control and relay unit.
-
Bentham Instruments Ltd
Our detection electronics portfolio comprises all the detection electronics elements required for the operation and automation of a high quality light measurement system, including photo-detector signal recovery and digitisation (with fully programmable DC, AC and lock-in amplifiers having current/ voltage inputs), high voltage supply, optical chopper control, detector thermoelectric cooler control and relay unit.
-
Coaxial Dynamics
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
4000 Series - Coaxial Dynamics
These 50-Ohm RF Load Resistors are light weight, dry coaxial loads that can be used in any position. All power ratings are for continuous operation. However, data is available for special applications and pulsed power conditions. Any of our Quick Match connectors can be used on these loads. Should you desire a connector other than the one included, it should be specified when ordering.
-
CL-10GSS - Automation Products, Inc.
Dynatrol® CL-10GSS Level Detector may be used for high-, intermediate-, or low-point level detection of bulk solids. It is constructed to handle extremely light weight applications that are difficult to measure like glass fibers, glass wool, paper dust, polyester powders and polymer powders. The CL-10GSS is typically used with bulk solids in the density range of more than 5 lbs/ft3.
-
Suzhou 3ctest Electronic Co.,Ltd.
State of the art electrostatic discharge simulator available in 18KV. It is the most ergonomic ESD gun without an additional base control unit. It can be operated via battery or mains. The easy to use touch screen, ergonomic design, modular R/C units, remote control software, built-in LED light and temperature and humidity display allows a trouble-free use in all types of test sites.
-
Raman - Wasatch Photonics
Our f/1.3 modular spectrometers can be configured for fiber couple or free space. They use our proprietary volume phase holographic gratings paired with f/1.3 optics. This allows us to build a high-performance spectrometer in a small package. These spectrometers constantly outperform larger more expensive units. They have high throughput and are ideal for applications that demand fast integration times or for low light applications.
-
MPX-SR3 - Arden Photonics LTD
Arden’s MPX Modal Explorer makes measurement of Encircled Flux easy, and accurate, and it complies with international standards. But if you are measuring laser-based transmission light sources for multimode systems you may need to use a test jumper assembly and fiber shaker in order to avoid “speckle”. Industry standards (for example IEEE 802.3aq and FOTP– 203) call for the use of a mechanical fiber shaker.
-
Profitap B.V.
Profitap fiber TAPs provide secure in-line network access for the monitoring of 1–400 Gbps fiber networks. By splitting the light flowing on the network link, fiber TAPs deliver an exact copy of the data for real-time monitoring and analysis, without disrupting the network. Passive fiber optic TAPs require no power, and therefore introduce no point of failure when deployed in a network.
-
GTB1684 - Guide Technology, Inc.
The GTB1684 is a light weight, high quality14.5Gbps, 4-Channel BERT system. It is the idealchoice for high speed serial bus testing.Accurate testing at today’s high speed seriallinks requires the test tool to generate veryclean signals with the lowest jitter possible. TheGTB1684’s fast rise time, low noise and lowjitter are evident in the high fidelity output eyeon all four channels.
