Showing results: 106 - 120 of 5968 items found.
-
OBB2 -
Astronics Corporation
The OBB2 is highly configurable and includes built-in standard peripherals (Ethernet, serial, and USB), along with four internal Cores that can be populated with a variety of databus protocols and discrete I/O modules. With the newest advanced set of MIL-STD-1553 and ARINC 429 modules, users can verify wave form compatibilities, test functions of bus shorts and opens, and—when combined with our CoPilot® software—perform lab, production and flight test verification and simulation right out of the box.
-
ICS Electronics
Control older devices that use the ANSI X3.28 protocol from the GPIB Bus. Available in board or rack mountable Minibox™ form.
-
U2C-12 -
Dimax
Dimax U2C-12, all-in-one USB-I2C, USB-SPI and USB-GPIO Bridge device, converts PC USB transactions to the I2C Master, SPI Master transactions and GPIO functions. U2C-12 turns your PC running Windows, Linux or MacOS into comprehensive I2C/SPI Bus master.
-
ZET 7076 -
ZETLAB Company
Previously it was widely thought that it is enough to receive sensor readings and to have remote control over them. But gradually there evolved a need for remote control, i.e. people need to receive sensors readings and to control their performance via Internet (for instance, on a portable device). Such possibility simplifies quite a lot of tasks since one can control performance of a system located at the other end of the city or even a country.
-
Electro Standards Laboratories
Supporting a variety of medias, applications, and entities such as Casino/Lottery VLT Networks, Industrial Process Control, Government Laboratories, etc.
-
-
MIRIG -
Holding Informtest
Мезонин MIRIG предназначен для приёма сигналов точного времени, их регистрации и синхронизации совместно работающего оборудования по протоколу IRIG-B
-
MC -
Holding Informtest
The MC mezzanine module is designed to receive external commands and issue synchronization pulses on the TTLTRG line (for VXI and other devices) and the LVDS line (for LXI devices).
-
Analog Devices Inc.
The RS-232 specification allows for reliable data transmission from one transmitter to one receiver at data rates of up to 20 kbps over relatively short distances (up to 50 feet). On more recent RS-232 transceiver chips, data rates of up to 1 Mbps are achievable over shorter distances (up to 5 feet). The most common applications for RS-232 transceivers are computers and peripherals, mobile phone data cables, and diagnostic data ports.
-
McLAREN Applied Technologies
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
NLINE-T1553 -
Alta Data Technologies LLC
Supports Full Real-Time Control the Same as a PCI Express Card in a Server! Much Better than a non-real-time USB.Full Hardware Interrupt Handler Support! AltaAPI SDK Provides Easy Integration – Use the exact same code as other Alta PCIe devices! Windows 10 Support Only
-
PK-232/USB -
Timewave Technology Inc.
The PK-232/USB brickwall filters have tighter bandwidth and steeper skirts for improved noise and QRM rejection. New PK-232 firmware (Ver. 7.2) allows a wider selection of filters than the original PK-232, so the filter can match the mode. The correct DSP filter is automatically selected when you choose an internal mode. In RTTY, Timewave’s proven Twin Peak Filters pluck the mark and space tones from the noise and QRM for great copy. In PACTOR, the filter bandwidth automatically changes when the baud rate shifts in response to the error rate of the link. In Morse (CW), the operator can preset either 100 Hz or 200 Hz bandwidth. The PK-232/USB is compatible with all Windows W2K,XP,Vista/Win7 software terminal programs for the PK-232.
-
Quasar 7Z01300 -
mks Ophir
The Quasar module provides a way to use Ophir sensors as a remote laser power/energy meter allowing optimum placement of the sensor and separate optimum placement of your PC or laptop with no connecting cables.
-
-
Maccor Series 4000, Model 4200, and Model 4300 Automated Test Systems -
Maccor, Inc.
The Maccor Series 4000, Model 4200, and Model 4300 Automated Test Systems can be configured with an M option. This option adds a Multiplexer to the test system which allows the channels to be connected to a Princeton Applied Research PARSTAT 4000 or Solartron Analytical 1260/87 impedance analyzer. With the impedance analyzer connected to the test system via the multiplexer the user can then program impedance tests in the Maccor test procedure which when reached will cause the test system to automatically disconnect the Maccor test channel from the device and connect the impedance analyzer to the device. When the impedance test is completed the test system will then automatically disconnect the impedance analyzer from the device and connect the Maccor test channel back to the device and continue with the programmed test procedure. For the Series 4000 Automated Test System, multiple multiplexers and impedance analyzers may be connected to a single test system. Contact the Maccor sales department with any questions concerning this option and for information concerning other supported models of impedance analyzers.