Showing results: 586 - 600 of 1086 items found.
-
SMT712 -
Sundance Multiprocessor Technology Ltd.
The SMT712 is a PXI Express (opt. Hybrid) Peripheral Module (3U), which integrates two fast 12-bit DACs, 2 banks of 1GByte DDR2 memory each, a clock circuitry and a Virtex5 Xilinx FPGA, under the 3U format.
-
PSV5000 -
Data I/O Corporation
At the core of all Data I/O's programming systems is the FlashCORE III programming engine. FlashCORE III is the industry’s most trusted programming engine. Based on a proprietary FPGA design, FlashCORE III with SuperBoost technology is optimized to program devices.
-
9740-D -
Strobe Data Inc.
Double speed Windows/NT Osprey Co-Processor for two times the system throughput, or more. Occupies one PCI slot. A writable control store, FPGA implementation of the PDP-11 architecture with 4 MBytes of tightly coupled, zero wait-state memory.
-
TEF0008-02 -
Sundance Multiprocessor Technology Ltd.
The Trenz Electronic TEF0008 is a FPGA to Mezzanine Card (FMC) based on VITA 57.1 FMC HPC Standard, with four SFP+ 10 GBit ports for fiber optical SFP modules. It is inteded for use on a FMC HPC carrier and can not be used stand-alone.
-
AES-FMC-IMAGEON-G -
Sundance Multiprocessor Technology Ltd.
The AES-FMC-IMAGEON-G HDMI input/output FMC module provides high-definition video interfaces for FMC-enabled baseboards. An HDMI video source can provide video content to the module. The module also provides an HDMI output to display FPGA driven video content.
-
ATS9625 -
AlazarTech
ATS9625 is a 250 MS/s 16 bit PCI Express waveform digitizer with an on-board, user-programmable FPGA. With fixed ac-coupled input range of 2.5 Vp-p and signal to noise ratio in excess of 75 dB, ATS9625 is an ideal solution for radio applications.
-
UTC006 -
Vadatech Inc
The VadaTech UTC006 is a double module, MTCA.4 format, MCH with front-panel fabric expansion and RTM support (PCIe optiononly). Fabric options include PCIe Gen3, 10/40GbE, Xilinx Virtex-7 FPGA, Cross Bar Switch (CBS), and SRIO.
-
CAEN S.p.A.
- Programmable FPGA to implement complex logic functions- VHDL coding expertise not required- User-friendly software tools for board programming- Pre-programmed set of standard functions (N1081B/DT1081B)- Different I/Os connectors and standards available (NIM, TTL, ECL, LVDS)
-
Wave Gen Xpress -
Byte Paradigm
A digital pattern generator is an essential stimulus source for almost every type of digital device: digital and mixed-signal ASIC, FPGA, microprocessors and microcontrollers. The digital pattern generator can be used early in the design cycle to substitute for system components that are not yet available.
-
FastX1703-DIG -
Alacron
The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.
-
JTAG Technologies Inc.
While many ICs are equipped with a JTAG (IEEE Std. 1149.1) boundary-scan register (BSR), a significant number of microprocessors and DSPs can be found with deficient or even non-existent BSRs. CoreCommander Micro uses the on-chip debug mode of processors to access ports and embedded peripheral controllers to promote ''kernel-centric'' testing. Similarly, in the case of today's Field Programmable Gate Arrays (FPGAs) test engineers can ''bridge'' from the JTAG interface to the resources of the gate array itself. Our CoreCommander FPGA product implements a translatorinterface that allows our JTAG hardware to control embedded IP cores via a variety of bus interfaces (e.g. Wishbone Avalon etc.).
-
783638-01 -
NI
12.5 Gbps, 8-Channel PXI High-Speed Serial Instrument—The PXIe‑6591 is designed for engineers who need to validate, interface through, and test serial protocols. It includes a Xilinx Kintex‑7 FPGA to implement various high-speed serial protocols, and it is programmable with the LabVIEW FPGA Module for maximum application-specific customization and reuse. The PXIe‑6591 takes advantage of FPGA multigigabit transceivers and up to eight TX and RX lanes. In addition to high-speed serial lanes, the PXIe‑6591 features digital I/O signals that support multiple logic families with per line, per cycle direction control.
-
OP-FW10R -
LINEEYE Co., Ltd.
OP-FW10R is a firmware to expand the measurement speed for bit synchronous communication such as HDLC/SDLC/X.25, CC-Link and SPI communication up to 10Mbps. Processing major part of the measurement process by FPGA, it enables capturing of communication data with time stamp of micro-second unit.
-
XJFlash -
XJTAG Ltd.
XJFlash is an FPGA-based advanced and innovative method that uses JTAG for high-speed in-system programming (ISP) of flash memories – all serial and parallel flash devices are supported. The most common use of XJFlash is programming the SPI/QSPI NOR flash used to configure an FPGA.
-
MDGG-8 -
W-IE-NE-R, Plein & Baus GmbH
The MDGG-8 is a single wide 6U VME multi functional FPGA based delay logic and timing module which provides often needed functions as gate, delay & pulse generator, logic fan in – fan out, coincidence register and scaler / pre-scaler.