Showing results: 136 - 150 of 1086 items found.
-
Model 57624 -
Pentek, Inc.
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Model 52624 -
Pentek, Inc.
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
eXpert Stream-to-Analysis -
Wuntronic GmbH
All Gage PCI Express CompuScopes are able to Stream waveform data through the PCI Express bus directly to PC RAM. By contrast, older Memory Mode operation required storage of data in dedicated digitizer memory prior to data transfer. Streaming provides two distinct advantages over Memory Mode. First, Streaming may overcome the acquisition time limit imposed by the volume of dedicated digitizer memory. Second, in Streaming Mode, the user does not need to await completion of waveform acquisition before accessing the resulting waveform data, which is necessary in Memory Mode.
-
Model 71810 -
Pentek, Inc.
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Supports Xilinx Kintex Ultrascale FPGAs- Front panel digital I/O can be used as a status and control or data interface- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
GX3756 Series -
Marvin Test Solutions, Inc.
The GX3756 is a user configurable, FPGA-based, 3U PXI card which offers 56, TTL I/O signals. The module consists of a daughter card and the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA.
-
PCI536 -
Vadatech Inc
The PCI536 is based on the Altera Arria-10™ GX1150 FPGA in F1517 package. The FPGA interfaces directly to the FMC+ DP 0-23 (single connector) and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. The PCI536 has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. It also has interface to two DDR4, 64-bit wide, with 16 GB total memory. This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.
-
783763-01 -
NI
The NI-7931 features a programmable FPGA and embedded processor optimized for deployment in the field for reliable, extended operation for applications requiring advanced I/O capability with embedded signal processing. It includes a Xilinx Kintex-7 325T FPGA, 2 GB of onboard DDR3 DRAM, and a dual‐core ARM Cortex‐A9 processor running NI Linux Real‐Time.
-
PCI592 -
Vadatech Inc
The PCI592 is based on the Xilinx XCKU115 Kintex UltraScale FPGA, which provides 5,520 DSP slices, 75.9 Mb RAM and 1,451,000 logic cells. The FPGA interfaces directly to the FMC+ DP-23 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 modules. It also has interface to three DDR4 memory channels (2x 64-bit wide and 1x 32-bit wide). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. The unit has x8 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10G/40G, SRIO, PCIe) without the need to go through the host.
-
PCI596 -
Vadatech Inc
The PCI596 is based on the Xilinx VU13P UltraScale+TM FPGA, which provides over 12,000 DSP slices, 360 Mb of UltraRAM and 3,780K logic cells. The FPGA interfaces directly to the FMC+ DP 0-31 and all FMC+ LA/HA/HB pairs, making it compatible with a wide range of industry standard VITA 57 and VITA 57.4 modules. It also has interface to DDR4 memory channels (1x 64-bit wide, 8 GB). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host. PCI596 has x16 PCIe edge connector routed to the FPGA PCIe Gen4 hard IP block. In addition, 16 uncommitted connection pairs are routed to a dual x8 expansion connector, providing direct connectivity to a neighbouring FPGA (e.g. via Aurora, 10/40GbE, SRIO, PCIe) without the need to go through the host.
-
Model 78630 -
Pentek, Inc.
Model 78630 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. A highspeed data converter, it is suitable forconnection to HF or IF ports of a communications or radar system. Its built-in data capture and playback features offer an ideal turnkey solution as well as a platform for developing and deploying custom FPGA processing IP.
-
GX3748 -
Marvin Test Solutions, Inc.
The GX3748 is a user configurable, FPGA-based, 3U PXI card which features 48 voltage comparator channels. The daughter board interfaces to the GX3700 FPGA baseboard which employs the Altera Stratix III FPGA. Each input channel can accept input voltage signals from 0 to 50 volts, with programmable threshold levels. Three of the 48 channels are supported by the board's timestamp event feature.
-
781502-01 -
NI
8-Slot, Spartan-3 FPGA, Ethernet CompactRIO Chassis - The NI-9148 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using scan-mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. The NI-9148 enables you to add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
783496-01 -
NI
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
783496-02 -
NI
4-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9147 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9147, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.
-
783376-01 -
NI
8-Slot, Zynq-7020 FPGA, Ethernet CompactRIO Chassis - The NI‑9149 is a rugged Ethernet chassis that you can use to add C Series I/O modules to any standard Ethernet network. You can program the chassis using Scan Mode for fast expansion of your real-time system or using the onboard FPGA for inline processing and high-speed I/O and control. With the NI‑9149, you can add high-performance I/O to your PC-based application or expand your CompactRIO, PXI, or industrial controller application.