End Face Cleaning
-
product
Tool, Fiber Optic Cleaning Pen, Multimode, Receiver/ITA, 2.5mm
910121192
Tool, Fiber Optic Cleaning Pen, Multimode, Receiver/ITA, 2.5mm
-
product
Accessory, Fiber Optic Contacts, Cleaning Kit
910121170
Accessory, Fiber Optic Contacts, Cleaning KitPlease note- This product cannot be shipped internationally and may only be shipped within the continental United States. Material Safety Data Sheets are available for two products in this kit. Click the red links below to download.This kit contains: Micro Duster Pressurized Air Canister Isopropyl Alcohol 4 oz Spray Bottle 2.5mm Wrapped Swabs, 5 Pack 1.25mm Wrapped Swabs, 5 Pack Cleaning Wipes (1 Box, 286 count) Isopropyl Alcohol Pre-Moistened Wipes, 50 Pack Connector Cleaner Cleaning Kit Case
-
product
EFEM Platform
Our EFEM Platform can act as a standard EFEM, or can be customized to suit your application’s cleanliness, handling technique, throughput, and form-factor requirements. From design to manufacturing, we offer units in varying complexity and precision and can integrate the needed hardware, software, vision, optics design, sub-micron metrology, environmental control and materials handling to fit your needs from single units to 4-wide.
-
product
Cleaning Kit
Diaclean
Proper performance of a fiber optic connection is strongly dependent on the cleanliness of the mated ferrules. DIAMOND connectors are thoroughly inspected and cleaned prior to shipment and do not require cleaning before being placed into service. After repeated mattings, however, or when degraded performance is observed, it may become necessary to clean the individual ferrules and mating sleeve. DIAMONDs cleaning set DiaClean contains all necessary tools for proper cleaning and inspection of the connector’s front-faces to help ensure optimal connector performances.
-
product
Cleaning
Air Guns
Fraser Anti-Static Techniques Ltd
For neutralising static electricity and removing dust and other contaminants.
-
product
End Face Inspection Microscopes
D SCOPE EFI – D SCOPE EFI-C – D SCOPE EFI-C LWD
The new D Scope EFI for MTP/MPO and multifibers field connectors is a cost effective microscope for inspecting fiber optic patchcords and cassettes.
-
product
Cabin Management & Cleaning
Honeywell Aerospace Technologies
The world of travel has transformed before our very eyes, and commercial transportation must adapt their services and processes quickly to meet shifting demands. From enhanced cleaning protocols to touchless entry points, Honeywell’s cleaning solutions significantly reduce disease-spreading bacteria and viruses. With convenient solutions to meet the needs of all types of commercial transportation modes, our cabin management and cleaning systems help maximize the health, safety and comfort of passengers.
-
product
Cleaning Validation
Cleaning validation, which is essential for quality assurance in pharmaceutical manufacturing, refers to the quantification of residues after cleaning of manufacturing facilities and equipment to verify that the amount is below a predetermined acceptable limit.
-
product
Fiber Cleaning Kit
TK1013
This is a general purpose fiber cleaning kit for most popular fiber optic connector styles with 2.5mm and 1.25mm ferrules. Replacement consumables are also available. The combination of wet and dry-cleaning items here are proven and well-accepted by most organizations.
-
product
Cleaning
Nozzles
Fraser Anti-Static Techniques Ltd
A fast, quiet, flat jet of ionised air for efficient static neutralisation and cleaning.
-
product
Automatic Cleaning and Calibration
Knick Elektronische Messgeräte GmbH & Co. KG.
Fully automatic process monitoring in combination with the analysis measuring system Protos and the retractable housings SensoGate or Ceramat. Highly accurate measurements even under difficult process conditions such as high pressure, high temperatures and high levels of impurities.
-
product
Portable Connector End Face Geometry Interferometer
Thorlabs’ Vytran® Connect-Chek® Interferometer automatically and precisely measures radius of curvature, apex offset of polish, and fiber undercut or protrusion on any PC or APC, single-fiber connector. The CC6000 interferometer uses a non-contact tilted-phase-analysis technique for fast, reliable measurements of connector end faces. This compact interferometer has a carrying handle and must be attached to a desktop or laptop computer (not included) with a standard USB 2.0 port for operation. The included CC6000 software, which is used to control the interferometer, can be installed on a computer with the minimum requirements in the table below. Designed for use in both the factory and the field, this interferometer provides crucial quality information needed to assure long-term performance of fiber optic connectors. One CC250P Mount for Ø2.50 mm PC Connectors and one RT250P Reference Tool for calibrating the CC250P mount are included with the CC6000 interferometer; mounts and reference tools that enable measurement of other PC or APC, single-fiber connectors are available separately below. When used with an appropriate mount for APC connectors, the CC6000 interferometer is also capable of measuring the APC angle and key error.
-
product
Inspection + Cleaning for High Volume Manufacturing Environments
AVIT-2020
AVIT-2020 is a fully automated system that removes human subjectivity from the entire inspect-clean cycle. With integrated cleaning and fast, robotic mechanics, operators simply press the process button, allowing them to complete a week’s worth of inspections in just a couple of hours with almost zero active operation.
-
product
Ultra Clean, High Concentration, High Flow Ozone Generator
SEMOZON® AX8415
The SEMOZON® AX8415 is the most innovative and versatile ozone generator developed by MKS. Ultra clean, high concentration, high flow ozone is produced by this generator's novel architecture and patented cell design, converting oxygen to >400 g/Nm3 of high concentration ozone for leading-edge applications in the semiconductor, flat panel display and photovoltaic industries.
-
product
High-grade type Gas Monitor for Chamber Cleaning End Point Monitoring
IR-400
The IR-400 offers real-time monitoring of the chamber cleaning end point during the deposition process. By optimizing the cleaning process, the IR-400 reduces cleaning time and gas usage. This reduction in cleaning gas usage leads to a reduction in chamber damage and increases the life times of all the systems components.
-
product
Radar Front Ends
FMCW
The transmit signal is derived from an external VCO signal, internally multiplied, which also acts as the LO for the receive mixer. The resulting IF is conditioned for gain and filtering as required. The IF also contains an industry leading IF noise figure, especially in the frequency range below 500MHz. Custom designs available, visit our custom design page for more information.
-
product
Face Masks Particulate Filtration Efficiency PFE Tester
GLE-20
GLE-20 is an oil-salt two-in-one Face Masks Particulate Filtration Efficiency PFE Tester. According to ASTM F1862-17, ASTM F2299-03 (2017), ASTM F2100-2019, BS EN14683-2019, BS EN 14387-2004+A1 2008, BS EN 136-1998, BS EN 140-1999, BS EN 143-2000 +C1-A1, BS EN 149-2001+A1, etc. It is used to test the particulate filtering efficiency of daily protective masks and medical masks, and to determine the obstruction performance of ordinary fabrics and medical protective masks against a constant flow of airflow.
-
product
Cleaning
Air Knives
Fraser Anti-Static Techniques Ltd
Produce fast-moving ionised air which can neutralise static electricity and remove contaminants.
-
product
Battery/Antifreeze/Cleaning Fluid Refractometer
RHA-200
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
Digital Hand-held Refractometer is a precise optical instrument that can accurately and quickly measure the refractive index, concentration and other parameters of various aqueous solutions.Dimensions: 55x98x39 mmWeight: 150gPower supply: Rechargeable lithium batteryUser-friendly operation interface, LCD display, making the operation more simple and convenient. More quickly measurements, more accurate and clearer.
-
product
Clean Room Torque Screwdrivers
With the growing trend of clean room manufacturing, the need for torque tools that meet stringent cleanliness requirements has increased. Responding to this manufacturing need, Mountz offers clean room torque screwdrivers. Clean Room screwdriver is a preset torque limiting screwdriver (internally adjustable). The cam-over design prevents overtorquing for your application.
-
product
Front End Processor
SoftFEP
Process telemetry and command data streams in satellite control centersConnect satellite control centers with networked antenna sites.Fully software-defined and customer-configurable.
-
product
End Face Inspection
Cleave quality inspection. High precision interferometers for checking the end face quality of cleaved optical fibers and for cleave process optimization. Crisp and clear fringe patterns and software with advanced measurement functionality. Ideal for use in production settings and when working with difficult to cleave fibers in laboratory environments. Fiber holder adaptors available for use with cleavers and splicers from the major splicer manufacturers. This facilitates easy transfer of the fiber from cleaver to interferometer and then onto the splicer with no need for reclamping.
-
product
Single Ended Test Probes
Single ended probes ranging from 0.4mm to 1.27mm pitchWide selection of plating options to optimize contact challenges and maximize probe lifeVarious length option to provide drop-in replacement capabilityTri-temp applications – 55°C to 155°C
-
product
Battery Front Ends
Renesas provides a comprehensive lineup of battery front ends to cover all battery management system protection, monitoring, and balancing requirements.
-
product
Medical Face Masks Flammability Tester
Sataton Instruments Technology CO., Ltd
Medical face masks flammability tester is to determine the fire resistance performance of medical face masks and full face masks. The tester can provide a specific flame and make the dummy head with facepiece move to the flame under a specific speed. The operator can observe the effects of the flame on the masks and facepiece. The tester is suitable for medical face mask, respiratory protective equipment and full face masks.
-
product
15' Cable, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97112
15' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
product
4-Pin Power D-Type Female to Unterminated With Tinned Ends
A008PF4-T-6A200
The 4-Pin Power D-Type Connector to Unterminated Cable Assy is constructed from PVC insulated 56/0.3 (12AWG) Copper wire. The connector can be secured to the product by screwlocks and the unterminated connections are coded to match the connector pin designation.
-
product
TrainLink™ End Of Train Device
NG5 ATX
Based on over 30 years of EOT experience, Wabtec's new generation TrainLink™ NG5 ATX has been expertly designed with industry leading communication capabilities featuring a durable external antenna and a lightweight, but rugged construction meant to withstand abuse from railway operations.
-
product
Analog and Digital Front Ends
ACQUA Front Ends
Measurement Front Ends (MFEs) convert the digital test signals of the communication analysis system ACQUA to the analog or digital formats required by terminal equipment, acoustic transducers, networks, network components, or system simulators, thus allowing complete tests in both transmission directions.
-
product
Signal, Patchcord, ITA, 72", QuadraPaddle Insert, Single Ended
7-151924000-072
Signal, Patchcord, ITA, 72", QuadraPaddle Insert, Single Ended
