Showing results: 76 - 90 of 90 items found.
-
EC-80P (Portable) -
NAPSON Corp.
*Auto-measurement start by probe head contacting to sample*3 measurement modes for wafer resistivity, bulk resistivity and sheet resistance*Easy set up to measurement condition by JOG dial*5 types of model for each measuring range*Resistivity probe can be changed by sample’s resistivity range
-
EC Epsilon EClipse -
inotiv
The Epsilon EClipse™ is the latest electrochemical analyzer manufactured by BASi. It is a potentiostat/galvanostat with a second working electrode for bipotentiostat measurements. It comes with software that enables the most popular electrochemical techniques such as cyclic voltammetry, chronoamperometry, and chronopotentiometry (select Techniques below for a more complete list). The Basic Plus software can be purchased to enable pulsed voltammetry and stripping voltammetry techniques.
-
360 EC-RTL -
OneSpin Solutions GmbH
During a typical development process, there are many occasions where a change needs to be made to a block, which must then be retested to ensure functional equivalence. For example, once a block has been proven to operate correctly, a designer may wish to optimize some section, maybe to improve the coding style, reduce the gate count or streamline operation. Today, an engineer must execute an entire simulation regression run to verify each change. This often requires a lot of time and may also need additional stimulus, with no guarantee that an exhaustive functional check will be performed.
-
Eurofins E&E
The Radio and Telecommunications Terminal Equipment Directive (R&TTE Directive 1999/5/EC) has been in place in the EU for many years serving radio and telecoms technology. To accommodate developments in radio equipment technology and to align with the requirements of the New Legislative Framework (NLF), the EU R&TTE Directive has been re-written. As of 2016, the European Commission replaced the R&TTE Directive with the Radio Equipment Directive (RED), which establishes safety and electromagnetic compatibility (EMC) requirements for equipment using the radio spectrum. Following June 13, 2017, after a one year transition, the RED 2014/35/EU replaced the R&TTE Directive. All new and existing products within the scope of the RED must comply in order to achieve CE marking.
-
Anton Paar GmbH
The MCR rheometer series from the market leader offers you one thing first and foremost: an open range of possibilities. Whatever your rheological requirements are and will be in the future – based on its modular setup, your MCR rheometer is efficiently and comfortably adapted and extended to meet your needs, from routine quality control to high-end R&D applications. An investment in an MCR rheometer is always a safe investment in longstanding technology: The air-bearing-supported EC motor, for example, was developed by Anton Paar and has been used in all MCR models for over 25 years to ensure accuracy across a vast viscosity range. It makes it possible to measure liquids with a viscosity even lower than water and also characterize stiff materials like polymer composites or steel by DMA – and everything in-between.
-
HVM200 -
Larson Davis, Inc.
The HVM200 is a small rugged vibration meter with built in Wi-Fi that can be used to measure hand-arm, whole body and general vibration. It includes the metrics and frequency weightings needed to measure human vibration. This 3 channel meter meets the requirements of ISO 8041:2005 and it is designed to measure per ISO 2631-1, 2 & 5 and ISO 5349 in support of the American Conference of Governmental Industrial Hygienists (ACGIH) Threshold Limit Values (TLVs) and the directive 2002/44/EC. This makes the HVM200 an ideal choice for an instrument used to demonstrate compliance with human vibration requirements and regulations worldwide.
-
YWX/Q-010X -
Lisun Electronics Inc.
Composite Salt Spray Test Chamber stimulate the actual natural conditions to do accelerated corrosion test, all the testing are based on common states on the natural environmental: such as combine with salt spray, hot air drying, humidity, low temperature and so on. The test samples are widely used on the intense changes in the environment, like automobile parts, aviation equipment, building materials, coating, electric and electrical machinery so on. YWX/Q-150X series is full compliance with ASTM D4728I, EC 60068-2-1, IEC 60068-2-14 and EIA/JEDEC JESD22-110-B standard requirements etc.
-
Extech EC-12880-P -
Extech Instruments Corporation
Extech EC-12880-P are two bottles of 12880 µS Conductivity Standard, 1 pint each of premade solution. EC-12880-P is for use with conductivity meters like the EC400 ExStik Conductivity/TDS/Salinity Meter or DO610 ExStik II DO/pH/Conductivity Kit.
-
Extech EC-1413-P -
Extech Instruments Corporation
Extech EC-1413-P are two bottles of 1413 µS Conductivity Standard, 1 pint each of premade solution. EC-1413-P is for use with Extech conductivity meters like the EC400 ExStik Conductivity/TDS/Salinity Meter or DO610 ExStik II DO/pH/Conductivity Kit.
-
Extech EC-84-P -
Extech Instruments Corporation
Extech EC-84-P are two bottles of Conductivity Standard, 1 pint each of pre-made solution. EC-84-P 84 µS is for use with Extech conductivity meters like the EC400 ExStik Conductivity/TDS/Salinity Meter or DO610 ExStik II DO/pH/Conductivity Kit.
-
LS-28-EC-QRS Series -
Lumistar Inc.
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
LS-84-EC-DRS Series -
Lumistar Inc.
Lumistar offers the LS-28 series of high performance multi-band multi-mode RF Receiver/Combiners in several different versions including rack mount, portable and modular formats. Complete solutions from RF to bits and/or RF to UDP data broadcast in Chapter 10 format are available. Available at any frequency range from 215 MHz to 6000 MHz, data rates to 50 Mbps.
-
imc Test & Measurement GmbH
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
MD-AWD-500-AC/EC-100/250 -
Mustang Dynamometer
The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.
-
OAKTON Instruments
Get easy-to-read and accurate readings with auto-hold, auto-stable, and real-time measurements with stability indicators. The Environmental Express® Oakton® 300 series multiparameter meters utilize smart sensor technology with sensor heads that feature a built-in digital circuit for automatic sensor recognition. Sensor information including sensor ID, calibration data, and measurement setup is stored in sensor head and viewable on the meter display when sensor is connected. Sensor heads are easy to connect and disconnect with waterproof push-lock connector. Sensor cartridges (pH and EC) are replaceable for a cost-efficient and environmentally friendly system. Blue LED light on the sensor head functions as a reading stability indicator, flashing until the reading is stable. Meter stores up to 10,000 data sets with date-and-time stamp for accurate and easy analysis. Quickly transfer data from meter to computer seamlessly via USB cable or wirelessly via Wi-Fi. Easily take measurements and conveniently store meter and electrodes with built-in foldable stand on the back of the meter. Three grooves on the meter serve as electrode holders, to hold up to three electrodes simultaneously.
