Decoder Test
Check model rail DCC and sound decoders.
-
product
PCI Express Host Interface SSD/Drive Decode Support
Teledyne LeCroy provides NVM Express, SATA Express and SCSI Express protocol decoding, analysis and test equipment to SSD storage companies worldwide. It works closely with the following organizations providing equipment to its members and conformance programs.
-
product
Plus Super Phosphor Oscilloscopes
SDS2000X
The SDS2000X Plus series employs SIGLENT’s SPO technology with a maximum waveform capture rate of up to 120,000 wfm/s (normal mode, up to 500,000 wfm/s in Sequence mode), 256-level intensity grading display function plus a color temperature display mode. It also employs an innovative digital trigger system with high sensitivity and low jitter. The trigger system supports multiple powerful triggering modes including serial bus triggering. History waveform recording, Sequence acquisition, Search and Navigate functions allow for extended waveform records to be captured, stored, and analyzed. An impressive array of measurement and math capabilities, options for a 50 MHz waveform generator, as well as serial decoding, mask test, bode plot, and power analysis are also features of the SDS2000X Plus. A 10-bit acquisition mode helps to satisfy applications which require more than 8-bit resolution.
-
product
Decoder Compliance Tests
Sarnoff Bitstreams™
Using SRI’s Emmy® award-winning technology, the Sarnoff® Bitstreams™ suite is the de facto standard for systematically and unambiguously testing decoders against industry standards. The Bitstreams visual and automated decoder tests work in a matter of seconds and do not require a reference signal or specialized decoder.
-
product
Cable Free ATE
CABLEFREEATE
Digalog Systems customizes resources to provide requirements or more cost-effective requirements that are not currently on the market.The CableFreeATE™ technology also affords lower cost and easier integration of some common offerings:- VPC 64 SPST Reed Relay- 0.1" Discrete Header 64 SPST Reed Relay- DL1-156R 72 SPST Reed Relay
-
product
Infotainment Test for Automotive Applications
Multimedia operating interfaces are complex control and display devices for functions such as entertainment, telephony, on-board computers and vehicle settings. The functional test of such complex control units and their networking within the vehicle architecture presents a particular challenge in every phase of the product design process.
-
product
Flexible Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131E
Achieve phase stability with this 96.5-cm cable when a DUT is connected, with adapter, directly to the test set port
-
product
Design for Testability (DFT Test)
Corelis can provide you with design consultation and an analysis of your design for boundary-scan testability. We will review your design and make specific recommendations that if implemented will improve the testability. We can also suggest improvements that will increase test coverage and allow boundary-scan to be implemented in a more cost-effective manner.This service also includes a DFT test coverage analysis that we recommend to do after schematic capture and before PCB layout. At this stage of product development, Corelis provides you with a comprehensive test coverage reports that identifies all of the boundary-scan nets and pins and classifies them as completely tested, partially tested, or not tested. The report also recommends where to add test points (pads) for physical “nails” access if additional test coverage is required.
-
product
Display Driver Test System
T6391
High-resolution flat-panel displays (LCDs / OLEDs) are becoming increasingly integrated. It is common for today's display driver ICs (DDIs) to contain a multitude of logic/analog circuits to manage advanced operations including touch-sensor functions. At the same time, the rapidly growing applications of LCDs / OLEDs in mobile electronics are driving demand for DDI's with smaller sizes and greater capabilities. These factors present serious IC-testing challenges. ADVANTEST's T6391 system is designed to address these needs along with DDIs' increasing number of pins and faster interfaces.
-
product
Modular Functional Test Platform
LX-OTP2
The OTP² system platform has recently been available in both the PXI and LXI versions. The OTP2 system platform enables the cost-effective and fast implementation of function test systems based on defined modules and function blocks. Thanks to the open system interfaces, customer-specific adjustments can be made at any time without any problems. When considering options for your next generation functional test system, it is important to assess the entire life cycle of the system and the associated costs and efforts. Use OTP² to accelerate development cycles and reduce the development effort for new functional test systems.
-
product
Fastest In-Circuit Test Platform
TestStation
Teradyne’s TestStation in-circuit test systems provide electronics manufacturers with reliable high-quality, high-volume testing for the latest printed circuit board assembly (PCBA) technologies that are used in automotive, industrial, computing, consumer, communications, and defense end-products.
-
product
Test Fixture Kits
More then ten years of experience in special, customized engineering and manufacturing brought us to the highest level of creating reliable, flexible and robust Test Fixtures. Currently our HQ is located in Vecsés, Hungary together with our R&D. Equip Group has Test Fixture Kit manufacturing plant in Serbia, focusing on supplying competitive, high – quality and high – volume products for the global market.With more then 180 employees, Equip – Test is able to offer our customers turnkey solutions in fixturing with test program generation. No matter if you have a simple or complex, high-density PCB (Printed Circuit Boards), or if you have DUT (Device Under Test) already assembled into metal or plastic housing, we can offer you a very stable technical solution.
-
product
RF Testing Platform for ATx05
AT118
The functional test of modern devices with wireless connectivity always requires RF isolated cameras, as the only way to have the parameters controlled and to guarantee operation under the specified conditions.
-
product
Off-Line Base Test Platform
6TL19
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible, and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
-
product
CPE Design Verification System
Jupiter 310
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
product
Conformance Test System
TS8980
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
product
Functional Test Fixtures
Reliable connections to device under test (DUT) test points are essential for robust functional test. Bloomy provides rugged fixtures and cable sets (ITAs) built for thousands and thousands of cycles in manufacturing environments. With the industry’s best mass interconnects and internal electronic keying, our fixtures are easy to change out and are automatically recognized by the test system.
-
product
Photonics Wafer Probing Test System
58635
The advancement of the photonics device technology continues to enable broader and more demanding applications in the industry.
-
product
ARINC-708/453 2-Channel Test & Simulation Module for the Weather Radar Display Databus
M8K708
The M8K708 module is an ARINC-708 / 453 2-channel test and simulation module for the Weather Radar Display Databus. The M8K708 supports two ARINC-708 / 453 channels, each selectable as transmit or receive. Each channel implements an 64K×16 FIFO and supports polling and/or interrupt driven operation.The M8K708 comes complete with Windows software, a C-driver software library including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application. In addition, Excalibur produces adapter cables that convert the carrier board I/O Molex™ connector to two twinax CJ70-49 connectors. The cable may be purchased at an additional cost.
-
product
TD-SCDMA Analysis Using NI PXI RF Test Instruments
NI-RFmx TD-SCDMA
The NI-RFmx TD-SCDMA personality is a highly optimized API for performing physical layer measurements on TD-SCDMA cellular standard signals. NI-RFmx TD-SCDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
Functional Test System Optimized For Real-Time Digital Bus Test
Spectrum HS
Spectrum HS is Teradyne’s fully integrated functional test system. Optimized for real-time test of low latency buses, it’s a high-performance system delivering excellent test coverage of current and future products.
-
product
PXI Semiconductor/IC Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
Stopper kit includedYAVCANCON2 for fixture identification not included
-
product
Noise Figure Analysis Using NI PXI RF Test Instruments
NI-RFmx Noise Figure
Measure noise figure, gain, Y-factor, effective temperatures, hot and cold power, and moreOptimized calibration and measurement routines for multi-DUT test using Y-factor and cold sourceSupports the PXIe-5668R 26.5 GHz VSA, the PXIe-5698 26.5 GHz preamplifier, and VSTsDesigned for use with industry-standard noise sources such as the Noisecom NC346 Series
-
product
W-CDMA/HSPA+ Analysis Using NI PXI RF Test Instruments
RFmx W-CDMA/HSPA+
The NI-RFmx W-CDMA personality is a highly optimized API for performing physical layer measurements on W-CDMA cellular standard signals. NI-RFmx W-CDMA is completely interoperable with all NI-RFmx APIs. It provides simple access to the most advanced optimization techniques such as multi-measurement parallelism and multi-DUT measurements. The result is extremely fast and high-quality measurements with minimal software development efforts.
-
product
H(3)TRB & HTGB Test Systems
SET offers two H(3)TRB and HTGB product lines which differ in the number of test object channels and the range of technical possibilities. The innovative systems are scalable, modular and standardized.
-
product
6TL19 Off-Line Base Test Platform
H71001900
The 6TL19 is a bare half-rack with castors for creating Off-Line, modular, flexible and reliable Base test platforms. The overall rack capacity is 11U (580mm depth).
-
product
Laser Diode Reliability Burn-In / Life-Test System
58602
Chroma 58602 is a high density, precision multi source measurement Unit (SMU) module with temperature control and exchangeable interface developed for burn-in, reliability and life test of optoelectronic components including laser diodes, VCSELs, VCSEL Arrays, silicon Photonics, photo-diodes and other similar components.
-
product
Test System for Detecting Exact PCB Short Circuit Locations
QT25
Qmax Test Technologies Pvt. Ltd.
QT25 employs a unique method to detect exact PCB shorts circuit locations and pin down the shorted components and tracks. It is designed in such a manner that it precisely detects exact short circuit locations across VCC - GND or a shorted component connected across a Bus or hair-line shorts between PCB tracks, Which is highly impossible to detect using conventional tools especially when they are connected parallel in circuit. It can also be used in measuring the contact resistance of switches and relays in its milli-ohm mode as a value add.
-
product
Test Fixture
16047E
Perform impedance evaluation of lead type devices of up to 120 MHz; includes a guard and a shorting plate
-
product
Automatic Test System
Automatic Test system is the ultimate solution for power electronic testing. The system includes a wide range of hardware choice such as AC/DC Sources, Electronic Loads, DMM, Oscillate Scope, Noise Analyzer and Short /OVP Tester. This flexibility combined with its open architecture software platform-PowerPro III, gives users a flexible, powerful and cost effective test system for almost all types of power supply testing.
