Showing results: 2491 - 2505 of 2780 items found.
-
ETS-88RF -
Teradyne, Inc.
Targeting the needs of power amplifier (PA) and front-end-module (FEM) semiconductor manufacturers, the ETS-88RF test system is aligned with the test challenges associated with these direct RF radio wave interface components. The precision with which the ETS-88RF can measure high-gain, wideband frequency performance, adjacent channel leakage and power supply efficiency makes this test system the most cost-effective alternative to bench set-ups. Teradyne routinely provides timely updates to a substantial library of RF Standards (such as 802.11xx and 3GPP) targeted for PA and FEM test.
-
782358-01 -
NI
40 GHz, Dual-Transfer PXI Transfer Switch Module—The PXI‑2798 can route RF or microwave signals in automated test applications. Designed to operate with less than 1 dB insertion loss at up to 40 GHz, the PXI‑2798 appears almost invisible to signals at much lower frequencies as well. You can use this module for basic signal routing or inserting and removing components in a signal path. The PXI‑2798 is also well-suited for passing high-order harmonics from RF upconverters or routing multiple sources to RF downconverters.
-
GX7017 Series -
Marvin Test Solutions, Inc.
A component of the GENASYS platform, the GX7017 offers the flexibility to incorporate the GENASYS switching subsystem with 3U and 6U PXI instrumentation in one compact, PXI chassis. Based on the 6U PXI architecture, the GX7017 can accommodate up to 9 GENASYS switch cards and 10 PXI modules, with 8 PXI slots supporting the GENASYS GX5960 digital subsystem. Up to 64 external resources can be connected to any of the test system’s switching resources / receiver I/O pins via a high performance, internal 16 wire matrix bus.
-
Cole-Parmer Instrument
Effective process control enhances the efficiency and performance of your operation. The heart of any sophisticated process is a controller that takes input from sensors and transmitters, measures process variables, and responds with output instructions to system components via relays and switches. We offer a wide range of process equipment including process controllers, temperature controllers, sensors and transmitters, signal conditioners, panel meters, and HMI devices. Plus we provide expert technical assistance to help you find the best solution for your application.
-
5530 -
Keysight Technologies
The configurable system offers all the components you need to perform a variety of measurements using the USB on your PC as the host controller and power source. For basic linear measurements you will need the USB Axis Module, USB Sensor Hub, Air and Material Sensors, Sensor Cables, Software, Laser, Laser Cable, Remote Control (optional)and the Linear Optics Set. Other available options include the Laser Tripod (with laser mounting plate), optics and fixturing kits for making additional types of measurements, and wheeled transit cases.
-
KRD41 series -
CME Technology Co. Ltd.
KRD41 series small drop tester is suitable for free-fall test of small consumer electronics and components such as mobile phones, walkie-talkies, electronic dictionaries, CD / MD / MP3 and so on, applicable standards JISC 0044 and IEC 60068-2-32. Through standard tests on electronic products (surface drop, corner drop, edge drop, etc.) and collecting data, it simulates the vertical drop impact of electronic products during transportation and handling. It provides a basis for the design of the product's buffer and vibration damping and the selection of structural materials.
-
ATE QT2256-640 PXI -
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Pasternack Enterprises, Inc.
Our RF termination loads (also know as terminators) are available in 1.85mm, 2.4mm, 2.92mm, 4.1/9.5, 4.3-10, 7/16 DIN, BMA, BNC, Type C, Mini SMP, MMCX, Type N, QMA, SMA, SMB, SMC, SMP, SSMC and TNC connector types. RF termination loads from Pasternack are organized into two categories, feed-thru terminations and RF terminations. Pasternack Enterprises RF load terminations include precision and standard versions and many are RoHS and REACH compliant. 0.25 Watts, 0.5 Watts, 1 Watts, 2 Watts, 5 Watts, 10 Watts, 25 Watts, 50 Watts and 100 Watts models. Pasternack RF terminations are offered with impedances of 50 Ohm, 75 Ohm or 93 Ohm. The frequency ratings for these RF coaxial load termination range from DC to 50 GHz. RF loads are available in female, jack, male, male to female and plug genders. Our RF termination loads varieties are RoHS and REACH compliant. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this RF terminator series is in-stock. Not just in stock, but also these RF terminations will ship the same day as they are purchased from Pasternack.
-
ViAcoustics
The Small Device Noise Emission Test System from VIacoustics is a turnkey solution for the measurement of noise emissions of small devices typically used in computers, consumer electronics, appliances and automobiles. The system includes all hardware and software necessary (see the components tab) for the determinations of sound power levels (1/3 octave band and A-weighted), emission sound pressure levels (normalized 1/3 OB, A-weighted and high resolution FFT) and *ISO 532B loudness. The system is designed to be operated by a technician for production level testing or to be used by an engineer in the product development process.
-
Weshine Electric Manufacturing Co., Ltd
mainly used to measure the wire resistance of cables, the contact resistance ofswitches, connectors, relays, the resistance of coils, motors, transformer windings, and equipment enclosures, lightning protection belts, ground beams, structures, cabinets, steel bars, Test the connection resistance between metal components of water pipes, windows, guardrails, radiators, assembly lines, etc. It is widely used in telecommunications, electric power, meteorology, computer rooms, oil fields, power distribution lines, tower transmission lines, gas stations, factory grounding grids, lightning rods, etc.
-
Magtrol Inc.
With over 50 years' experience in dynamometer design and torque measurement, Magtrol has revolutionized the industry. Magtrol's NEW Micro Dyne, capable of measuring extremely low torques (2.0 mNm can be resolved to 0.0004 mNm), is DESIGNED EXCLUSIVELY for testing miniature and micro motors.For the utmost convenience, the Micro Dyne is packaged as a COMPLETE MOTOR TESTING SYSTEM. Everything that is needed to accurately and efficiently test miniature motors and micro motors is included with the purchase of a Magtrol Micro Dyne. The only component that needs to be supplied by the customer is a laptop or desktop personal computer and a motor power supply.
-
NX Hipot -
Dynalab Test Systems, Inc.
* 50 to 1500VDC Hipot Testing* 50 to 1000VAC (optional) * 5Mohm to 1Gohm Insulation Resistance * Simple 4-button user interface * Tests for continuity and shorts * Tests a variety of components * Precision resistance measurements * Continuous high speed scanning for real time complete status information of harness assembly progress * Keyed security access and control * Built for rough industrial environments * 2 serial ports for connection to printers and scanners * Standalone operation * Uses a high capacity memory card * Available from 64 to 1024 test points * Networkable
-
Delserro Engineering Solutions
Under normal conditions it may take years to gather failure data on the life cycle of new products. Through accelerated life testing the overall time to failure can be reduced to weeks by increasing the frequency of the field loads and by removing insignificant stress components. In addition, life cycle testing on a product can be reduced or accelerated dramatically by increasing the stress levels to higher than normal. Putting a product through Accelerated Life Testing can reduce test time from weeks to days while still achieving satisfactory results saving both time and money.
-
FLIR A50/A70 Smart Sensor -
Teledyne FLIR
FLIR A50 and A70 smart sensor cameras are ideal for users who want built-in, on-camera analytics and alarm capabilities for condition monitoring and early fire detection applications. With options for Wi-Fi, an integrated visual camera, and ONVIF S compatibility, FLIR A50/A70 cameras are a flexible, configurable solution to meet the unique needs of automation customers across a broad range of industries. When used as a system component for cloud and Industrial Internet of Things (IIoT) solutions, A50/A70 cameras can help companies protect assets, improve safety, maximize uptime, and minimize maintenance costs.
-
TA-3A/B -
Tech-Aid Products
This weather radar test fixture is a combination of the established WXT-250 series fixture and the RDR-2000 and RDR-2100 radars so that a single panel will provide many features that are still required today. The gyro simulator built into the panel is usable for either radar being tested and eliminate's plugging in any external simulator. The features for both product lines as shown in their respecting CMM's are provided on the panel so that full testing and alignment of these radars and their system components can be tested and/or evaluated. If you require any changes or other product versions please give us a call.
