Filter Results By:
Products
Applications
Manufacturers
Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
- Advanced Telemetrics International
product
Battery Powered Telemetry Systems
Advanced Telemetrics International
ATi’s Battery Powered Telemetry Systems are ideal for transmitting coupled data signals from sensors, which are mounted on rotating shafts or machinery to a stationary receiver.
-
product
PATHWAY
ATS
The ATS takes QST to a new level, delivering painful and non-painful stimuli at a temperature range of 0C to 55C (expandable to -10C to 55C) with heating and cooling rate of up to 8C/sec. This opens new research opportunities in deep cold and heat pain studies.
-
product
Flicker Measuring Probe for LCM ATS
A712306
The Chroma A712306 Flicker Measuring Probe for LCM ATS is specifically designed for adjusting the flicker on LCM automatically following the FMA(Flicker Modulation Amplitude) standards defined by VESA (Video Electronics Standards Association) and JEITA (Japan Electronics Information Technology Industries Association) for flicker measurement.
-
product
LED Power Driver ATS
8491
1. DC Electronic Load : Chroma 6310A/6330A Series2. Transducer Unit/Module*1 : Chroma A849101/A849102, A849103, A8491043. Time/Noise Analyzer : Chroma 80611 & 80611N card4. Sytem Controller*2 : Industrial PC5. DC Source: Chroma 62000P Series6. Digital Power Meter : Chroma 66200 Series7. OVP/Short Circuit Tester : Chroma 806128. ON/OFF Controller : Chroma 80613*1 : A849101 transfers UUT output signal to voltage signal, and measure by 84911 LED power driver measurement card (200kHz). The optional 80611N Noise card is required for 20MHz ripplecurrent measurement.*2 : The controller includes both 84911 LED Power Driver measurement card and 84903 control card.- 84911: Measure rms current, dimming current/frequency/duty, timing, power & ripple current (200kHz)- 84903 : Provide BL control signal(DC level, PWM, SM bus), and enable ON/OFF signal.C Source : Chroma 6500/61500/61600 Series
-
product
12/24 CH Insertion Loss/Return Loss Automatic Testing System
CA3201
UC INSTRUMENTS CA3201 12/24 CH INSERTION LOSS/RETURN LOSS AUTOMATIC TESTING SYSTEM is special designed for MPO/MTP fiber cable and multi-channel fiber optical devices like PLC device. It also can be easy changed into AWG DWDM devices testing system ifwe change 1310 /1550 nm light source into UC INSTRUMENTS’ tunable laser source.
-
product
Fully Automatic Eddy Current Crack Test System
ROTO-SCAN
Foerster Instruments, Incorporated
The fully automatic crack test system ROTO-SCAN was specially developed for the testing of rings. The mechanical equipment has been developed for the gentlest possible handling of the test pieces and features a compact and low-maintenance design. The test probes seamlessly scan the inner and outer contours of the test pieces, thus ensuring 100 % testing of the rings.
-
product
Automatic Safety Test System
LS9955/56
The LS9955/LS9956 Automatic Safety Test System is according to GB4706.1, IEC/EN60335-1, UL60335, GB7000, IEC60598, GB4943, IEC60950 and GB9706.1. It used for luminaries, home application and motor tools safety test in production line or Lab R&D.
-
product
Test System
DA-1 ATS
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
product
In-Line Full Automatic Testing System
ALMAX
Automated press unit with board loading belt.ALMAX can become automated in-line type in-circuit tester in case our ICT is integrated. And it also can become automated in-line function tester as well.PLC is not used in order to reduce cost as a PC control mechanical part.Press unit is 4 shaft structures which reduce unbalanced load and contact fail of probe pins.
-
-
product
Microhardness Tester
MT91 Series
Newage Testing Instruments, Inc.
The Newage MT91 System is an automatic microhardness testing system that uses the Rockwell method for the hardness result. Hardness is measured based on the depth of penetration rather than using an optical system to determine hardness based on the impression diameter.
-
product
olar Cells and Modules Online Measurement System
PV-LIT
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
product
Battery Pack ATS
8700
Chroma transfers its successful experience in 8000 ATS which is quite well-known in the power electronics industry to the battery application field by developing the Test Items specifically for the battery industry. It can perform automatic tests on the Battery Management System (BMS), semi products and finished products tests on the production line as well as provide long term maintenance and service to the battery module. 8000 (8700) ATS has flexible hardware architecture that can select a variety of hardware devices, such as DC Power Supply, Electronic Load, LCR Meter and 6 1/2 digits Meter, etc. to comply with different automatic testing requirements for various applications. In addition new hardware and test items can be expanded to meet the demands for inspecting the highly customized battery products with diversified tests. The capabilities supported are:
-
product
Battery (EV) Automatic Test System
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
product
Benchtop Discrete Component Tester
Imapact 7BT
The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability.
-
product
RF Conducted Immunity Test System
RFCI61000-4-6
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
product
Electric Vehicle Supply Equipment ATS (EVSE ATS)
It is a customized system based on Chroma 8000 ATS specializing inverification of EV Supply Equipment (EVSE) and complying with SAE-J1772 in programming the test items for operation.
-
product
Power Electronics Test Solutions
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
product
Resistivity Meters
SSR-MP-ATS
Integrated Geo Instruments & Services Private Limited
The instrument design incorporates several innovative features and advanced techniques of digital circuitry to make it a reliable Geophysical tool providing high quality data useful for mineral and groundwater exploration and any other Geophysical applications. The SSR-MP-ATS sends the entire current into the ground without wasting power for constant current generation thus increasing the signal strength to probe deeper layers.
-
product
Phase Noise Test System
PN9000 System
Noise eXtended Technologies S.A.S.
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range. Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a NIST tested instrument.
-
product
Protection Relay Testing
ARTES
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
product
Inline Handler W/Bypass Line Master
6TL35
A perfect basis for a heavy-duty, reliable, high precision, and automatic integrated Test system for medium to high demanding environments. Important technical and economic advantages due to their modular structure and expansion capability are evident. The production testing environment will be flexible and efficient, helping towards the always valued Return of Investment.
-
product
LXI High-Density Matrix
Our LXI High-Density Modules are single and double pole matrices available in a wide range of configurations including versions with the added flexibility of dual analog bus. These high-density matrices are ideal for signal routing in large automatic test equipment (ATE) systems and are suitable for applications where a simple start-up process is required and for applications requiring control over large distances.
-
product
LED Power Driver Test System
Chroma C8000
Chroma Systems Solutions, Inc.
The Chroma 8491 ATS is equipped with optimized standard test items for LED driver testing (lighting & TV backlight). The user is only required to define the test conditions and specifications for the standard test items to perform the test.
-
product
Test System
DA-2 ATS
The DA-2 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
product
High-Power LXI Matrix Modules
Pickering's high-power LXI matrices are a single pole module available in a variety of configurations and are suitable for power signal routing in large automatic test equipment (ATE) systems. They are available with a selection of X and Y sizes as well as partially populated configurations.
-
product
Electric Vehicle AC Charging Compatibility ATS
8000
It is a customized system for Electric Vehicle AC Charging Compatibility testing.Hardware : Integrated by AC Source/Power Meter/DC Source/Function Generator/Scope/ EVSE CP & PD Simulator…。Software : Fully complies with SAE-J1772, CNS15511 test requirements
-
product
Three-phase Fully Automatic Test System
TS33
Calmet Smart Calibration Devices
The Calmet TS33 portable test system consists of a three-phase reference meter of accuracy class 0.02%, 0.04% or 0.1% and an integrated three-phase current and voltage source up to 3x120A/600V. The TS33 is designed for analysis of complete metering installations and local mains conditions.
-
product
Automatic Tablet Testing System
UTS 4.3
The UTS 4.3 LAB is a universal and fully automatic tablet testing system based on the long-proven UTS 4.1 - this was developed for industrial use and can be found in production worldwide. The UTS 4.3 LAB is now equipped with the database-driven, intuitive all-in-one touch software and no longer requires additional software solutions for most areas of application.The functionality of the software can be extended modularly and individually adapted to your needs and requirements. FDA regulations can be fulfilled with the optional FDA-21-CFR-Part-11 module.With UTS 4.3 LAB – as with the proven UTS 4.1 IPC – you can test round, oval, square and rectangular tablets as well as numerous special shapes. For difficult oblong tablets, the globally used Oblong Centering System (OZB) can also be integrated.
-
product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
product
Server Power And Back Up Unit Test Solutions
Built on the proven Chroma 8000 ATS platform, these customizable solutions are specifically designed for automated testing of server PSUs, power shelves, rack power systems, bidirectional DC/DC converters for BBUs, and low-voltage high-current DC/DC converters for motherboards.
