-
Product
Memory Test System
T5221
-
The T5521 is a memory test system that supports wafer test and wafer burn-in test of non-volatile memory devices such as NAND flash, housed within a multi-wafer prober to reduce test floor footprint.
-
Product
Four-module test set
F8200
-
Use the F8200 Power System Simulator for testing single-phase conventional schemes, digital protection systems, and more. This four-module F8000-series instrument is available in four standard configurations of HVA Current, HVA Voltage, and Low-Density Logic I/O modules.
-
Product
Linemen's Test Set
TeleTalker 330
-
Triplett Test Equipment & Tools
The Triplett TeleTalker™ 330 is a high performance lineman's test set with a weather resistant seal. This butt set offers many standard features not found on more expensive models like dedicated store / redial buttons, adjustable volume, Pulse and Tone dialing, and more. The high impact and weather resistant case allows for this product to be used in all demanding industry settings and features a full 3 year warranty. The user-friendly layout helps installers get the job done effectively with ease. The TeleTalker™ 330 requires no battery for main use and can store up to 10 frequently dialed numbers. Complete with angled bed of nails (JS Popper) test clips.
-
Product
Injection Transformer
J2101A
-
The injection transformer is presently the prevalent method for connecting the network analyzer to the circuit being tested, and is primarily used for control loop stability measurements. The goal of the transformer is to inject a signal into the control loop being measured, without impacting the performance of the loop. In order to accomplish this to a reasonable degree, The transformer is isolated and therefore is capable of floating on a high voltage, such as a Power Factor Corrector (PFC), which is often close to 400VDC. Measuring voltages that exceed the voltage rating of the FRA inputs require attenuation probes.
-
Product
DC Hipot Test Set
KVZG
-
KV Hipot Power Test Equipment Co.,Ltd
DC Hipot Tester is applied to measure output voltage and leakage current for zinc oxide arresters, magnetic blowing arresters, power cables, generators, transformers, circuit breakers and other equipment.
-
Product
Benchtop Communication Test System
ATS3000A
-
The ATS3000A is designed using Astronics Test Systems’ proven Synthetic Instrumentation architecture. Featuring 23 instruments, and both Automated and Standalone modes to test, record, and diagnose faults, the unit provides complete RF, Analog and Digital capabilities. The ATS3000A also includes the sophisticated IF and baseband I/Q Digital Signal Processing required for modern radios. The fieldupgradeable, software-defined architecture features easy-touse graphical user interfaces and enables testing with minimal operator intervention. Test Program Sets areavailable for a full range of tactical radios, or you can create new TPSs easily using the included TestEZ® software suite.
-
Product
Liquid Test Fixture
16452A
-
The 16452A provides accurate dielectric constant and impedance measurements of liquid materials. The 16452A employs the parallel plate method, which sandwiches the liquid material between two electrodes to form a capacitor. An LCR meter or an impedance analyzer is then used to measure the capacitance created from the fixure.
-
Product
PRO Test Set
TS® 52
-
Fluke Networks’ new TS52 PRO Test Set features the latest in test set technology. Designed with a superior, radiant liquid crystal display (LCD) user interface, it allows you to see what cannot be heard in any outside plant environment.
-
Product
IEC61850 Relay Test Set
NF802
-
NF802 is full digital IEC61850 relay test set, equipped with 8 optical ports, and powerful data processing capability, can realize full digital IEC61850 protection relay testing.
-
Product
Digital and Analog Test Sets
-
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
Product
Test System
UltraFLEX
-
The UltraFLEX test system delivers the power and precision you need for complex SoC devices built for mobile applications, networking, storage or high-end processing. Choose UltraFLEX when your device mix and throughput goals demand the highest speed, precision, coverage and site count.
-
Product
Imperial Test Executive
ITE
-
The Imperial Test Executive (iTE) is a UI shell that sits on top of National Instruments TestStand. It provides a simple but elegant interface to execute your NI TestStand sequences. The iTE software was designed to allow general operators to execute ATE testing software without requiring any knowledge of NI TestStand. Training an operator to use this system typically takes less then 5-minutes.
-
Product
Primary Injection Test Systems
-
Primary current injection testing is utilised in high current/high voltage scenarios found at large electrical installations such as substations. A large current (between 100A and 20,000A depending on system specifications and test requirements) is injected directly on the primary side of the electrical system such as a circuit breaker. The objective of the test is to identify how the system operates under various levels of current load.
-
Product
APU Test Set
H296G Series
-
The H296G Series is a flight line diagnostic tool thatmonitors selected parameters and provides enginecontrol during APU trimming.
-
Product
Radar Altimeter Test Set
EA-6061
-
The EA-6061 Radar Altimeter Test Set is designed to test and calibrate any and all radar altimeter systems regardless of protocol or encryption. The EA6061 provides multiple, programmable delays with front panel and/or remote computer control. It features ultra wide bandwidth, low loss, high isolation, and high dynamic range. Able to simulate altitudes up to 6350 feet, the test set operates from 4 to 5 GHz and offers NIST traceable altitude accuracy up to 2 inches
-
Product
110 GHz, 1.0 Mm (m-f) Test Port Cable 10 Cm
11500JK10
-
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
Product
Test Port Adapter Set, 2.4 Mm To 2.4 Mm
85130G
-
The Keysight 85130G test port adapter protects the test set port from connecting directly with the device under test. It has a special rugged female connector that connects to the network analyzer test port. This special connector does not mate with a standard male connector but converts the rugged test set port to a connection that will mate with the device under test. This set contains a NMD-2.4 mm (f) to NMD-2.4 mm (m) adapter and a NMD-2.4 mm (f) to PSC-2.4 mm (f) adapter. The frequency range for these adapters is dc to 50 GHz with a return loss of 23 dB or better.
-
Product
Multifunction Substation Test Set
STS 5000
-
STS 5000 is a multifunction substation maintenance & commissioning test system for current, voltage and power transformers designed to perform primary tests requested in substations commissioning. It allows to perform accurate tests on CTs, VTs, PTs and ground grid.
-
Product
Electronics Testing Solutions
-
Don’t cut corners when it comes to developing high-quality electronics functional testing solutions. Ball Systems helps you ensure you deliver the quality your customers expect by providing open and reliable advanced technical testing solutions.
-
Product
Protective Relay Test Set
POM2-6143
-
POM2 series protective relay test equipment is the best modular designed relay tester with local control system. There are 2 models, the POM2-6143 and POM2-3243, the POM2-6143 with 6×15A and 4×300V.
-
Product
EV& Charging Pile Test Set
AC Testing
-
With the Industrial development globally, Electric Cars is becoming more and more popular gradually in different countries. In the future, we can say that Electric Vehicles shall replace the ordinary cars soon and there are many charging piles, recharging station built up to meet the requirements to EV charging.
-
Product
Test Handler
M6242
-
Optimal Test Handler for Mass-Production DRAM, with Double the Throughput.
-
Product
Optical Loss Test Set (OLTS)
MaxTester 940/945
-
First tablet-inspired, multifunction optical loss test set (OLTS) delivering insertion loss, optical return loss and fiber length measurements at two wavelengths in five seconds via fully automated bidirectional FasTesT™ analysis. With its step-by-step reference wizard and intelligent fault diagnosis, the MAX-940/945 provides expert guidance throughout the test process to ensure immediate efficiency by first-time users while removing risk of errors or negative loss—a common source of issues when testing low loss fibers.
-
Product
Level Test Set
ET 91
-
100 Hz to 2.4 MHz selective/wideband Level Meter & Generator,with Spectrum Analyser and Z/RL/LCL Bridge
-
Product
80 DIOs, 8AIs, 8AOs JTAG Boundary Scan Resources Unit Expansion
YAV9JTAH
-
80 DIOs8 Ais8 AOsCompatible with all JTAG vendors
-
Product
Test Port Cable, 1 Mm
11500K
-
Connect test ports to devices, fixtures, or probe tips with this 20-cm cable featuring a return loss of 16 dB minimum
-
Product
Capacitance And Tan Delta Test Set
-
*DIGITAL DISPLAY for Capacitance and Tan Delta*NO NEED of calculation*SAVING OF Result and INTERACTIVE DOWNLOAD*SOFTWARE*High Resolution for Tan Delta -5 0.00001 (10 ) measurements*Easy to use*Safety Protections incorporated
-
Product
Adjustable Test Stab Set
-
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
Product
Altitude Digitizer Test Set & Simulator
ATS-400
-
Test & Simulate Altitude Encoder Parallel and Serial I/O all in One Rugged Test Set! The TCI Model ATS-400 is designed to test, display and simulate the output of Altitude Reporting Equipment, which conform to the ICAO Standard for SSR Pressure Altitude Transmission. In accordance with the U.S. National Standards for I.F.F. Mark X (SIF)/Air Traffic Control Radar Beacon System SIF/ATCRBS.
-
Product
RAMP TEST SET
AN/USM
-
Tel-Instrument Electronics Corp.
The AN/USM-708 Multi-Function Test Set provides unsurpassed reliability and ruggedness designed by an established and well recognized company with 50 years in the design and manufacture of aviation ground support and bench test equipment.
