-
Product
Resistivity Meter with Multi Electrode
POLARES
-
Till this moment the use of Electrical Resistivity Tomography (ERT) for geology has always been basically the same since its debut, based on the original vertical Electrical Soundings (VES) principles: applying a continuous current to two stakes inserted into the ground and measuring the corresponding voltage between other two. The applied current and thus the relative tension have always been continuous, with an inversion in polarity for each measure. The new tool POLARES uses an alternate current, instead, sinusoidal type, with an adjustable frequency.
-
Product
Transformer Winding Resistance Meter
10A
-
*10A DC continuous current in 4 ranges of 0.01A, 0.1A, 1A and 10A.*4 ½ digit display for higher resolution.*Dual channel measurement.*Suitable for operation in energized switchyard conditions.*Specialized protection circuits for suppression of inductive voltage kickback.*SMPS based - lightweight and portable.
-
Product
Ground Resistance Tester
2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
High measuring accuracy, high speed, easy to use, especially suitable for using in laboratory and automatic testing line. Test current AC / 5 ~ 30 (a), resistance Ω (0 ~ 600 m), time (1 ~ 99 s) shows at the same time. Test time can be arbitrary setted. Test alarm value can be arbitrary set up. Pass/fail sound and light alarm.
-
Product
Resistance Temperature Detectors - RTDs
-
Ashcroft® RTD sensor assemblies monitor temperature in industrial, process and hazardous installations. Available with Pt 100 and Pt 1000 RTDs, they are designed for use with either DIN 43772/T.2 or ISA-ds 49 style thermowells along with DIN and ASME type lag extensions. A wide selection of aluminum and 316 stainless steel connection heads make these RTDs configurable to the requirements of nearly any installation.
-
Product
Programmable Insulation Resistance Tester
-
AllWin Instrument Science and Technology Co., Ltd.
Electrical resistance testingLCD displayOutput Voltage: 1.0V~1000VThe insulation resistance range:100kohm to 100Gohm
-
Product
Winding Resistance Meter 15Amps, 2 Channels Rack
WR14R
-
Raytech Digital Winding Resistance meter WR14 R is the rack mount version of the WR14. They are designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
Product
4-Way Resistive Power Dividers DC To 27 GHz
-
Pulsar Microwave manufactures resistive dividers from DC to 27 GHz. They have a rated input power of one half watt maximum. VSWR of 1.5:1 or better maintained throughout band at all ports. Resistive dividers can be fitted with SMA male or female connectors and are available in three outline packages.
-
Product
Resistivity Meter of Powder Composites
RM-200
-
The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.
-
Product
Winding Resistance Meter 50Amps, 2 Channels
WR50-12
-
Raytech Digital Winding Resistance meter WR50-12 is the enhanced version winding resistance system with a most advanced demagnetizing circuit. It is designed for high degree of accuracy for the measurement of very low resistance of any inductive loads.
-
-
Product
Metal Foil Low Resistance Chip Resistor
MFF
-
*Low Resistance / TCR / EMF / Inductance*Excellent long term stabilityRoHS compliant and halogen free.*Lead free.*High precision current sensing and voltage division.
-
Product
Ground Resistance Clamp Meter
61-920
-
*Auto ranging*Auto power off*Hard case included*2-year warranty
-
Product
Non-Contact (Pulse-Voltage Excitation Method) Ultra-Low Sheet Resistance Measurement System
PVE-80
-
*No damage measurement by non-contact Pulse-Voltage excitation method*Easy to measure & carry around, Removable stage plate*Easy operation and data processing by PC with Software*Measurement result can shown by 3 types of measurement unit (Sheet resistance[Ohm/Sq], Electric conductivity[S/cm], Electrical conduction[S])*Pulse-Voltage excitation method : Pat. No.5386394 Joint development with Chiba Univ.
-
Product
Earth and Resistivity Testers
-
Earth tester offering selective earth, soil resistivity, earth coupling and continuity measurements
-
Product
10KV High Voltage Digital Insulation Resistance Tester
KM 6213AIN
-
Kusam Electrical Industries Limited
• The KM 6213A IN is the KUSAM-MECO premium model of High Voltage Digital Insulation Resistance Testers.• The KM 6213A IN has new added features with a low consumption High Performance processor.• It displays results much faster and has more advanced features.• The KM 6213A IN has Automatic Polarization Index and Dielectric Absorption Ratio Calculations.• Results are displayed on the new High Contrast LCD. It’s mounting angle makes it more readable for all users, in different working conditions.• The user’s manual reflects the new features and added benefits of this instrument.• It has Auto-Off, Auto-Stop, EnerSave™ and is a non destructive tester.• Once you start the tester, it waits for your selection. You can go up and down in voltage to select the voltage at which you want to test the insulation. Once you have selected that voltage, you need to connect the test leads to the Insulation Tester to measure. Then it measures voltage to ensure there is no voltage present on the equipment under test. If there is a voltage present, it will warn you to disconnect the circuit before proceeding. If it’s free of any voltage, then you can proceed with the testing. This ensures that no damage is done to the Insulation Tester KM 6213AIN.• One of the new innovation on this tester is also the way the new unique calibration process works. It’s fully digital, has no moving parts and does not require expensive and complicated jigs or computers systems to be calibrated. It’s cheaper to maintain than any other Digital HV Insulation tester on the market today. The KM 6213AIN is supplied standard with our Premium test Leads Kit, the AL-50.
-
Product
Spread Resistance For Slanting Polished Sample Of Semiconductor By Tow Kinematically-mounted Probe Contacting .
SRS-2010
-
*Resitivity map along with depth direction, thickness of epitaxial , depth of PN junctin and carier density profiles
-
Product
Digital Earth Resistance Tester
8020 ER
-
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage. ● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Frequency : 820Hz.● 0Ω adjustment.● Battery operated.● Data hold function.● Low battery indication.● Calibration performed with supplied test leads.● Simplified measurement probe is also provided for two-wire measuring method.
-
Product
Earth Resistance & Resistivity Meter
MRU-200
-
MRU-200 is the only meter in the market which uses all measurement methods.Possible measurements:- earth resistance measurment with 2-pole, 3-pole,4-pole method,- impulse earth resistance measurement, two kinds of measuring impulse 4/10s, 10/350s,- earth resistance measurement without disconnecting measured earths (using clamp),
-
Product
Fully Automatic Transformer Winding Resistance Tester
-
Measure DC resistance of transformers windings etc. Introduction: The NMC ''TDR'' is a high precision, new generation, light weight large output current and micro-processor controlled tester. This replaces old DC wheat stone bridge and double arm bridge for measurement of DC resistance. ''TDR'' adopts new advanced test current power supply technology, four terminal measurement, digital display of resistance value and test current. ''TDR'' is powered by 220V AC mains single phase supply. The measurements are accurate as the test current is highly stable. High automation is achieved with automatic discharge warning.Principle: The constant current generated is fed to the resistance under test through the current terminals and the voltage drop across the resistance under test is measured and displayed in ohms. A true four terminal measurement is used to eliminate the need for lead resistance compensation.
-
Product
XR Resistive Reactive Load Banks
-
Mosebach Manufacturing Company
Mosebach’s XR series load bank offers you a range of options for resistive reactive loads in both lower voltages of 480 and 600 or MV at 4160 and higher. Outdoor rated user friendly for years of use.
-
Product
Contacts Resistance Tester
JYK II
-
•Instrument IPC architecture for domestic production of all models of metal contacts SF6 switchgear, GIS combination of electrical, vacuum switch, oil switch and column switches, contacts and so on.•Sensor: Acceleration speed sensor, rotation speed sensor, linear stroke sensorinstallation is very easy and simple.•Trigger: The trigger, external trigger, the sensor is triggered. Sensor can trigger the circuit breaker manually switching characteristic test, such as a manual column pole division switch.
-
Product
Clamp-On Type Earth Resistance Tester / Leakage Current Clampmeter
KM 1620 / KM 1720
-
Kusam Electrical Industries Limited
KM-1620 / KM 1720 single-jaw type Earth Resistance Tester is widely used for earth resistance testing of the equipments in the field of power, telecommunication, as well as the other electrical equipments. It features easy operation, high-accuracy and good adaptation of testing environment.
-
Product
Digital Surface Resistance Test Kit
PAS-853BRM
-
- Surface Resistance Kit from 0.01 ohm to 9.99x1012 ohms- Nominal Full Range Tolerance Averages <±5%- Fully Automatic Resistance Range, Test Voltage and Electrification Period control- Determines if a surface is Dissipative, Conductive, or Insulative- Measures resistance point-to-point(Rtt) and point-to-ground (Rtg)- Measures resistance of Static Control Floors, ESD Work Surfaces and Packaging Material- Conforms to all ESD Association Standards for Resistive Characterization- Includes 2 each Conductive Rubber Electrodes- Packaged in a hard shell Carrying Case- Certificate of Calibration Traceable to NIST included
-
Product
Handheld Digital Multimeter, AC/DC Voltage, Continuity, Diode, Resistance, Temperature, 3.5, 2000
72-13435
-
*Clear LCD Display*Equipped with comfortable protective cover, test probe holder*2m drop test, precision protection*Auto Power Off*Auto Backlight Off*Loud Buzzer Sound*Knobs shift smoothly, in-line with ergonomics*Powered by AAA 1.5V x 2 batteries*12-month limited warranty *view Terms & Conditions for details
-
Product
Insulation Resistance Meter
AMIC-15k1
-
The partial discharge indicator PDI. Diagnosis of insulation systems based on standard measurements of IR, DAR, PI, SV, RT, DD. Allows to test the electrical durability of the tested object - indication of breaking voltage. The high resistance to electromagnetic interference ensures uninterrupted operation in power plants and near high-voltage transmission lines up to 1200 kV AC and 500 kV DC.
-
Product
Thermal needle system thermal resistivity / conductivity measurement
MTN01
-
Hukseflux Thermal Sensors B.V.
The MTN01 Multi-purpose Thermal Needle System allows performing fast measurements of the thermal resistivity or conductivity of soils. It is specifically designed to be reasonably robust, as well as accurate. It is therefore suitable for laboratory as well as field- measurements of soil thermal properties. The sensor is a Non-Steady-State Probe (NSSP), TP07, which is mounted on the Insertion Tool, IT02. The system is operated using a hand-held Control and Readout Unit CRU01.
-
Product
Resistivity Cell For N1413 With B2980 Series (26/50/76 Mm Diameter Electrodes)
N1424C
-
The N1424C is designed to operate specifically with the B2985B/87BElectrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424C to the B2985B/87B.
-
Product
Resistance & Resistivity Probes
-
Surface and/or volume resistance measurements are key parameters in describing materials' electrical properties. ETS offers a variety of probes to support numerous industry requirements and applications.
-
Product
Electrical Resistance Probes
-
Electrical resistance (ER) corrosion probes are commonly used in petroleum, chemical processing, and other environments where on-line corrosion rate readings are required. Whereas test coupons must be removed from the process for evaluation, corrosion probes can allow corrosion rate determination without probe removal.
-
Product
Digital Earth Resistance Tester
ERT-1501
-
Electronic Digital Earth Resistance Tester is direct replacement of the conventional hand generator type tester. It is designed for measurement of the resistance of earthing used in the electrical equipment as well as for measurement of ground resistivity. It can be used for measurements of the other low regular and liquid resistances. It can also be used for measurement of voltage AC, voltage DC and resistance. This instrument finds wide application for testing earthing installation in power based industries, telecommunication networks and electrical traction systems etc.
