-
product
MOSFETs For High Frequency Amplifier
The MOSFETs shown below are best suited for amplification of high-frequency signals.
-
product
Test System
ITC57300
The ITC57300 Dynamic Parametric Test System mainframe accepts Test Heads that perform nondestructive transient measurements on semiconductor devices such as Insulated Gate Bipolar Transistors (IGBT), power MOSFETs, diodes, and other bipolar devices(requires additional optional bias power supplies and custom personality boards). Included in the mainframe are all test equipment and software necessary to analyze and perform resistive and inductive switching time, switching losses, gate charge, Trr/Qrr, and other transient tests.
-
product
Ultra High Frequency Vibrometer
UHF-120
Polytec?s New UHF-120 Vibrometer Laser-Doppler Vibrometers (LDV) can characterize the out-of-plane vibrations at ultra-high frequencies. Polytec?s UHF-120 extends the vibration frequency bandwidthup to 600 MHz.
-
product
High 1.73 (49.00) - 8.00 (227.00) High Performance Bias Ball Probe
POGO-1L24-8
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
FMET Systems
The Failure Mode and Effect Testing system allows the shorting of any I/O pin to any other I/O pin, including one of 4 common "Rails". Users can establish rules to prevent unwanted shorting conditions.
-
product
M² Measurement Systems
Thorlabs' M2 Measurement Systems provide self-contained, turn-key solutions for measuring M2, divergence, focus diameter, waist position, Rayleigh length and other laser beam quality metrics. Pre-configured, factory-aligned systems covering wavelength ranges between 250 nm and 2700 nm are available. Choose from among systems that have a scanning-slit beam profiler, a camera beam profiler, or no beam profiler.
-
product
Embedded Systems
Active Silicon designs and manufactures custom embedded systems, often integrating our leading-edge image acquisition technology. Typically, units are designed for a specific OEM application often in the field of medical devices, industrial automation or remote monitoring. Systems are designed to meet various safety, quality and medical standards as appropriate, as well as being designed for long product life retaining the same fit, form and function for many years.
-
product
Portable Telemetry Systems
Lumistar’s portable receivers and test transmitters take the state of the art technology found in the PCI receivers and simulators and install it into a hand held units. Our luggable Telemetry Systems can be configured using our card level products into unique custom solutions.
-
product
Voltage Regulation & TransformerMonitoring
One of the essential features of the voltage regulators is the possibility to implement special functions via customer-specific programs without interfering with the firmware of the regulator. The programs can be created online using a simple editing tool. All necessary program elements, incl. help texts and sample program lines, are included with every regulator.
-
product
High & Low Temperature Chamber
NEWARE offers powerful enviromental test chambers to provide comprehensive testing support for your battery testing.
-
-
product
High Voltage Passive Probes
The PPE6KV-A and HVP120 can handle up to 6000 Vpeak transient overvoltages and are designed for probing up to 2000 Vrms and 1000 Vrms respectively. Fast rise times, excellent frequency response, and a variety of standard accessories make these probes safe and ideal for high voltage measurement applications
-
product
Dual Sensor Enhanced Vision Systems
EVS
Enhance your safety and situational awareness while flying with Max-Viz dual sensor enhanced vision systems (EVS) from Astronics. These multi-spectral imagers include a long wave infrared sensor, a visible light + near infrared sensor, and patented blending and dynamic range management image processing to enable pilots to see clearly during day and night.
-
product
Provides 3 Wire Voltage Output
SEM1620
The SEM1620 signal conditioner provides a 3 wire isolated voltage output signal and accepts RTD, Thermocouple, mV and passive current sensor inputs
-
-
product
Meteorological System
200M
The Model 200M is a complete instrument for the measurement of Atmospheric Dew Point, Ambient Temperature, % Relative Humidity, or other Psychrometric Variables. It employs the very reliable optical chilled mirror sensing technique which provides a primary measurement of dew point, and is traceable to NIST. The Model 200M is ideally suited for installations requiring continuous, automatic, and unattended measurement of humidity over a very wide range.
-
product
Standard Voltage 50-Pin D-Type Connector & Cable Accessories
The Standard Voltage 50-Pin D-Type connector is used on PXI switching products to provide a medium density connector solution. Connection solutions for modules with High Voltage Rating D-Type connectors are also available.
-
product
High Speed Thermal Printer
6041
• RS232C serial interface via a 6-pole RJ12 socket• Tested to comply with FCC Standards• Designed for use with Associated Model 6044 and similar devices• Four AA Batteries included• Imported
-
product
Voltage Controlled Amplifiers
Teledyne Microwave Solutions (TMS) offers a variety of high-performance voltage controlled amplifiers operating over a 5 to 2500 MHz range. These VCAmps feature an AGC range of 20.0 - 50.0 dB and Response Times from 3 – 25µs. TMS has a broad range of component products to meet your demanding needs.
-
product
CT/VT Test System
Fully pre-wired comprehensive turn test system. *Suitable for CTs up to 6000A & VTs up to 132kV. * Precision to (0.005 class) internal multi-ratio standard CT. * Internal 4KA current source. * State-of-the-art Instrument Transformer Test Set AITTS-98 with computer & printer interfaces. * Electronic potential divider facilitates testing any VT ratio upto 132kV. * Current & potential burdens.
-
product
ADAQ Data Systems
Atec’s Data Acquisition and Control System (ADAQ™) is a modern, full-featured, highly integrated hardware and software solution that is applicable for use with most commercial and military turbine engine test cell applications. Built upon National Instruments’ respected LabVIEW platform, ADAQ™ is robust, versatile, user friendly, and specifically designed to handle the demanding requirements of engine testing. It links seamlessly to digital engine modules (FADECs, DEECs, EECs, ECUs) as well as legacy analog and mechanical controls. Users can create, remove, calibrate and display channels, as well as generate custom calculations, screens and reports. Beyond the most impressive manual throttle control and operation available, Atec’s ADAQ™ additionally offers the option of fully automated testing.
-
product
Portable Test System
MT686s
Actual value, vector, curve displaypower generationerror measurementMeasurement of harmonics up to the 40thVoltage supply via existing measurement voltage
-
product
Wafer Inspection System
JRT Photovoltaics GmbH & Co. KG
In close cooperation with well-known providers of inspection systems, we provide modular systems for quality control and classification of raw wafers.
-
product
Systems
Our systems use an open and flexible architecture to create a platform allowing integration of technology and modules with short system set-up times which result in a reduction of costs.
-
product
Data Logging System
Motor101A
The Motor101A measures and records on and off status changes for motors or other equipment drawing up to 200 Amps. The state change occurs when the current switch exceeds the 150mA set point. This allows for most basic equipment to be monitored.
-
product
Precision Voltage and Current Sources
VI-700
The VI-700 Voltage and Current Source is a versatile precision dialable or remotely programmable voltage and current source. Its three ranges provide up to 20 V full scale (200 V with the HV option), and down to 100 mV resolution; and 20 mA full scale down to 0.1mA resolution. Both voltage and current outputs are available simultaneously. The output is set by a range selector and thumbwheel switches in the LOCAL mode, or by a digital input at the rear panel. The REMOTE mode control can be a RS232 or IEEE-488 interface.
-
product
High Voltage Non-Contact Current Probe
P02-0802
The TESCO High Voltage Non-Contact Current Probe (Catalog No. P02-802) was developed using current sensor technology. It is a two-piece, True RMS ammeter with a fiber optic link between the high voltage sensor and the readout at ground potential. The sensor is mounted on a hotstick and slipped over a high voltage line.
-
product
High Temperature Infrared Thermometer
PIRT30
Modern Housing DesignBuilt-in Laser PointerType K Temperature Measurements20 Point MemoryAutomatic Capture Emissivity for TargetingLaser TargetingLCD With BacklightCelsius or Fahrenheit ModesLaser On/Off SwitchAutomatic Power OffDisplay Hold FunctionOptical Resolution (Distance to Spot Size): 13:1Temperature Range: -50 to 550 C, -58 to 1022 FTemperature Resolution: 0.1Type K Temperature Range: -50 to 1370 C, -58 to 2498 FType K Temperature Resolution: 0.1 up to 2000, 1 over 2000Response Time: <1 sec.Basic Accuracy: +/- 1.5% of ReadingEmissivity: Adjustable 0.10 - 1.0Dimensions: 7.09' H x 4.21' W x 1.57' DWeight: 4.76 oz.Sold as : Unit
-
product
Equipment Failure Diagnosis System and Safety Management System
A system for diagnosing failures of rotating machinery such as turbines, motors, pumps, fans, and compressors, which are major facilities in nuclear power, hydropower, thermal power plants, petrochemical plants, shipbuilding, and aviation, through displacement sensors.
-
product
Compact Baking System
LSC series
HORIBA's best-selling baking system has been developed to meet the requirements of today’s high technology industries. Without the need of a carrier gas, the system can provide stable vaporization of materials such as TEOS (at a rate of 600 SCCM) and H2O (at a rate of 2 SLM). For ease of access all device maintenance can be performed from the front of the unit.
