-
Product
Lan Cable Tester
3PK-NT015N
-
Open/short wiring testConnected wires displayNo wire or termination indicationWrong connection / Non-parallel connectionEthernet 10 base2 termination value detectionBattery low indicationBuzzer insideBNC for testing 10 BASE2 terminator valueIsolation resistances 50 K ohms test
-
Product
Temperature Rise Tester
WS-1
-
Applied to test electrical accessories heating conditions when connected to load current, whether the temperature rise of electrode is compliance with standard requirement or not. And it can effectively detect whether the plug bush is slants thin and whether plug and socket cooperated with all right. It is designed and manufactured according to IEC884－1, GB2099.1-2008 and other relevant standard of electrical accessories.
-
Product
Digital Leeb Hardness Tester
TIME®5350
-
Beijing TIME High Technology Ltd.
TIME Group manufactured the first Leeb hardness tester in China in 1989 and has been the leading manufacturer of hardness testing equipment since then. Among all the TIME hardness testers, TIME®5350 is the best one with all the features. It looks like a mobile phone, easy to carry and makes a perfect tool for on-site hardness testing. Maximum 32GB MicroSD card can be used to store measured values.
-
Product
Electrical Safety Tester
-
PSE AG has developed an electrical safety test that combines different tests for the testing of PV modules. With our four-in-one tester it is possible to test the following according to IEC 61215-2 and IEC 61730:
-
Product
Pin Brinell Tester
-
Newage Testing Instruments, Inc.
The Pin Brinell is a cost effective instrument, which uses a calibrated shear pin to control the amount of load applied. Provides consistent loading regardless of operator. Tests in 100 - 730 equivalent Brinell range.
-
Product
Smart Electric Tester
SET-12
-
The SET-12 Tester is a portable device for measuring electrical parameters. Unique combination of the most needed measurements into one device allows for a quick diagnosis of faults.
-
-
Product
Bench top Dielectric Withstand tester
HYPOT III
-
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
-
Product
Closed Cup Flash Point Testers
-
Labodam closed-cup flash point testers are compact, stand-alone solutions which determine the low temperature operability in diesel fuel, biodiesel, blends and gas oils. They are designed as per Test Methods for Flash Point of Petroleum Products (Pensky-Martens Closed Cup Methods).
-
Product
Universal ADI Tester with Rate Drive
TA-400
-
A Universal ADI Test Panel built to test one of the Astronautics indicators. Panel includes meter drive capability and a specific synchro auto-rate transmitter circuit that allows rates of up to 355 deg/sec. The standard ARINC capabilities make this a universal type tester.
-
Product
Fuel Injection Pressure Tester
33900
-
Test gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Test all Chrysler cars with Multi-port turbos and some TBI.Use on older Ford TBI systems not equipped with small Schrader test valve.Includes Large Gage with hang-up hook calibrated from 1-100 PSI (0-7.0 BAR).
-
Product
Portable Circuit Breaker Tester
PI-1600
-
The PI-1600 Circuit Breaker Tester incorporates modular design and flexibility to provide unequaled capability in a portable package. The PI-1600 test set is two testers in one, incorporating the PI-800 and PI-AUX. The PI-800 section can be used alone, on 120 or 240 VAC supplies, generating continuous current of 400, 800, amps at 4.2 kVA, with peak output to over 10x. When configured for the PI-1600, the PI-AUX output unit is connected in series or parallel to the PI-800. The PI-AUX boosts total power to 9.8KVA, and allows testing of draw-out breakers and MCB’s to 1600 Amps. The units are housed in rugged interlocking suitcase-size enclosures. Each piece weighs no more than 125 pounds, allowing one-person hand truck mobility. Basic operation is very simple, and the proven MAC-21 control instrumentation provides optimal output control and measurement. The MAC-21 instrumentation is supplied in a separate rugged portable case, interlocks on top of the PI-800, and connects to a cable in the rear of the test set.
-
Product
Abrasion Tester
rHT SeriesHB SeriesHT Series
-
Abrasion tester checks the abrasion of solid materials. such as metals, composites, ceramics and more.The test is performed on worn materials such as tires, shoes, belt and more.* Worn out condition* The loss of the weight* The loss of the physical volume* The thickness that been worn out, etc* Use NBS standard gum to ratio the endurance characteristic of abrasion for this material.
-
Product
Protocol Conformance Tester
TS-PCT
-
The R&S®TS PCT is a compact full range protocol conformance test solution in line with GCF and PTCRB requirements. It supports the entire device certification process for protocol testing and can be extended to operator acceptance testing by adding software.
-
Product
Capacitance and Inductance Tester
JY6700
-
Capacitance measurementsInstrument can test take a single capacitor without stitches in test group capacitance to bring convenience to test. It will show test results of capacitance while show test
-
Product
Contact Resistance Tester
JYL
-
As a high current passes through a pair of mechanically independent metallic contacts, the contact resistance must be as low as possible. Increasing the contact resistance of the contact often causes a large voltage drop on the contact, which reduces the input power of the load equipment. If the contact resistance of one or two contacts becomes large, the three-phase voltage of the load equipment will be unbalanced, causing phase loss operation.
-
Product
Water-cooled Light & Weather Fastness Tester
TF422
-
TESTEX Testing Equipment Systems Ltd.
Water-cooled Light & Weather Fastness Tester, to determine the color fastness, aging resistance of textiles, plastics, rubber products or materials by objecting to the simulated conditions of nature weather (daylight, rain, temperature and humidity, etc.). The tester simulates both light and dark cycles and nature weather conditions by rack sprays and water-cooled long-arc-xenon lamp equipped.
-
Product
Partial Discharge Tester (Dry Type)
-
Partial Discharge testing is a way of detecting voids or imperfections in insulators that would lead to overheating and breakdown under normal operating conditions. Due to the nature of the signal being measured, this test is very susceptible to electronic and RF noise and a proper corona-free properly isolated test chamber is required.
-
Product
High Voltage (Hipot) Cable Tester
CH2
-
The easy-wire CH2 was designed for commercial, military, and aerospace applications. Running on powerful Windows-based software, the CH2 offers unrivaled testing capabilities at an unparalleled price. Compact, easy-to-use, and FAST (shorts/mis-wires detected in <1 sec for 20,000 points), the CH2 is positioned to become the ''''tester of choice'''' for high-end users.
-
Product
LINE-CORD AND MULTI-WIRE CABLE TESTERS
LCT-3
-
Model LCT-3 Line-cord tester is an automatic test set to check continuity, polarity and dielectric breakdown on three-wire line cords.
-
Product
Oxygen Sensor Tester And Simulator
7650
-
Peaceful Thriving Enterprise Co Ltd
This device is designed to test and to simulate 1V Zirconia and 1V/5V Titania type oxygen sensors. The simulation can help user to exam the function of the ECU. Moreover, it can analyze the type of connection wire.
-
Product
Heat Deflection Tester
-
Apparatus is used to determine the Heat Deflection Temperature or the Vi cat Softening Point. All the specimens are charged with a constant load and immersed in a bath, where temperature is increased at a standard velocity. The attained heat resistance rate of plastic materials is a widely required parameter for product characterization, for quality control, as well as for evaluating their conformity to the previewed applications.
-
Product
Digital Earth Resistance Tester
MODEL - KM 2030
-
Kusam Electrical Industries Limited
Display : 3½ Digit LCD display. Ground resistance measurements from 0 ~ 01Ω to 2000Ω with 0.01Ω resolution. Earth Resistance : 20Ω / 200Ω / 2000Ω. Accuracy : 20Ω : ± (2% + 0.1Ω); 200Ω / 2000Ω : ± (2% + 3). Earth Voltage : 0 ~ 30V. Accuracy : ± (3% + 5). Resolution : 0.01Ω. Working LED Indicator. Data Hold Function.
-
Product
Semiconductor / FPD Inspection Microscope
MX61L
-
Motorized Microscope for 300mm dia. Wafer/17 inch Glass Substrate use Reflected/Transmitted Illumination.
-
Product
Earth Resistance Testers
-
Earth Resistance Tester is widely applied in ground resistance measurement, loop resistance measurement in fields such as electric power, telecommunications, meteorology, oil field, architecture and industrial electrical equipment, etc. When measuring ground system with loop, there is no need to disconnect the ground wire without auxiliary electrode, which means safer and faster.
-
Product
PC Based Rotor Tester
4008RJ
-
The PC Based Rotor tester is the most reliable, fast and cost-effective way to detect faults in the Rotors in less than 10 seconds. This Rotor Tester can only Test small sized Rotors having stack length less than 300 mm and weight less than 10 kgs.
-
Product
FPD Tester Signal Module
A040209-05-04
Signal Module
A040209-05-04 is a MIPI signal module board and complies with the MIPI DSI v1.2 / MIPI D-PHY v1.1 signal specifications and standards. A040209-05-04 is used with the FPD Tester and can be applied to MIPI Display testing, providing MIPI Panel standard signal and other related controls.
-
Product
Insulation Tester
AD-2050
-
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
Product
Digital Earth Resistance Tester
8PK-ST1520
-
Capable of measuring earth voltage (Vac.) 2mA measuring current permits earth resistance to test without tripping earth leakage current breakers in the circuit. Battery operated. Auto power off function. Data hold function. Small and light weight.
-
Product
IEC60335 Standard Electrical Temperature Tester
CX-w15
-
Shenzhen Chuangxin Instruments Co., Ltd.
Standard Test corner/room conform to IEC60335-1:2004. and GB4706.1-2005. can be used to the temperaturetest of all kinds of electronic products supply, in conformity with the standards requirement of the environmental conditions.
