-
product
Signaling Control and Monitor Equipment
MS 1303
The Railway signaling unit is used to receive the input signals from the field for validating and clearing route for trains. After receiving the signals, signals are isolated and various tests are done inside the system to ensure the received signals reliability and produce clearance signal to railway line. For security reasons card signature has been given to each card in the system. System consists of digital input modules, digital output module, digital read back module, RS232 interface with 80486 processor board. It is an ISA Bus Back plane based system.
-
product
Monitor / Annunciator
RTP-1
The RTP-1 Monitor is a general purpose annunciator. Designed for 19 “ rack installations, the RTP-1 is complete with a noise immune filter. The ten point RTP-1 features latching memory. Easy to install and easy to operate, this low power monitor has front panel plug-in replaceable LEDs for indication and a single system Test and Reset buttons.
-
product
Phase Monitors
NAI''s AC- and DC-powered Phase Monitors are used to protect three-phase loads from damage due to phase reversals or phase absence. Contacts may be used to disconnect the load or to operate alarm circuits or both. Upon application of power, the output relay energizes if all phases are connected and the phase sequence is ABC. If any phase becomes disconnected or if the phase rotation is abnormal, the relay immediately de-energizes. These monitors are specifically designed for rugged defense and industrial applications.
-
product
Condition Monitoring System
Cut costs and boost productivity with a condition-monitoring tool designed for ease of use and scalability. The Dynapar OnSite™ system is a powerful predictive maintenance system targeted at preventing failures before they occur. It can slash unscheduled downtime, improve efficiency of route-based vibration analysis, and provide real-time analytics and trending to warn of possible machine failures.
-
product
PoE Voltage Monitor Detect & Verify
PE-400
PE-400 is specific to test and verify PSE or Ethernet outlet either a standard/active PoE or a NON-standard/passive PoE to avoid damaging Non-PoE device as well as monitor and display available Voltage simultaneously. It built-in PoE interface controller to trigger on 802.3 af, at and bt switch and verify standard PoE type either 802.3 af or 802.3 at, and power source either End or Mid or both, and power polarity as well as display voltage values. The operational voltage which should be measured when installing a new PoE system or when you troubleshooting an existing system.
-
product
Active Network Assessment and Monitoring Platform
Hawkeye
Keysight Network Applications and Security
Network performance and user experience are critical aspects of your business. It is vital to understand customers’ perception of your website, application, and network services. NOT knowing impacts your revenue stream. Ixia’s Hawkeye continually measures network performance and service status. If there is an issue, Hawkeye helps you identify it, quantify it, and ultimately resolve it – before your customers experience it.
-
product
Clamp type AC Current Sensor／for Power Monitor
ZCT-33S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Ultra compact size*AC 0.1A～150A*Current measurements of feeder
-
product
Monitor Chlorophyll Fluorometer System
PSP32 Plant Stress Probe
The monitor chlorophyll fluorometer system is designed to dramatically increase the capabilities of plant monitor systems while also providing more affordable solutions for measuring larger plant populations. The revolutionary daylight dark adaptation capability allows measurement of photoprotective mechanisms, state transitions, chloroplast migration, and photoinhibition at different times of day.
-
product
27” LED-Framed Gaming Monitor With Touchscreen
GM-270S
ADLINK’s GM-270S LED-framed gaming monitor is specially built for casino gaming applications, such as video lottery terminals and slot machines. The GM-270S features 10-point PCAP touch screen and addressable LED frame is ideal as the interactive screen of a slot machine, making players feel more engaged in the game.
-
product
Environmental (Radiation) Monitoring System
Hawk® EMS
The Hawk® EMS is a wall or tripod-mounted radiation monitoring and alarm system designed for use with the Hawk® Radius dual sensor radiation probe. Each EMS System comes with a Hawk Radius Probe. The system is extremely energy efficient and can run for weeks on an internal 9 volt back-up battery if power fails. It is well suited for operating on a small solar panel, which is an optional accessory. The Hawk® EMS features two displays that show the radiation levels measured by each of the probe’s two detectors: the weatherized “pancake-style” Geiger-Mueller tube — which measures alpha (if configured for it), beta, low energy gamma, and x-radiation — and the energy-compensated gamma tube which measures penetrating gamma dose rate. The probe can be mounted next to the EMS system or outdoors, or in adjacent rooms on cables up to 100 ft in length. Standard cable is 3 meters in length. Optional signal booster can support cable lengths longer than 100 feet. Optionally the system can also be configured to share data on ethernet or wireless networks.
-
product
Water Activity Measurement, Moisture Meter, Measurement and Monitoring of AW Value
The measurement of water activity or equilibrium relative humidity (ERH) is a key parameter in the quality control of moisture sensitive products or materials.
-
product
Indoor Air Quality Monitor and Controller
VAT930-CO2/VAT930-CO2-VOC35
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Indoor air quality monitor and controller ( temperature meter. humidity meter . CO2 meter.VOC meter).
-
product
4-Channel Broadcast Monitor
The COMM-connect Entry Level Broadcast Power Monitor type 3025 can control two external RF Measuring heads. The high dynamic range with external couplers and RF measuring heads cover from 1W to 1MW. Equipped with the RMS Probes the Power conversion algorithms handles multi carrier, multi mode signals. With the 3026 Diode base probe the power readout gives good repeatable results. The power readout is auto scaled and VSWR will be calculated between the two probes. The COMM-connect Entry Level Power Monitor gives a number of application to monitor and control the last part of your RF network installation from transmitters to the antenna.
-
product
Micro Volume pH Monitor
UP-100
Redevelops HORIBA's founding pH measurement technology using new ultra-small capillary electrode. HORIBA's UP-100 affords ultra-low sample consumption of just 500 uL/measurement, enabling continuous pH monitoring for a variety of critical manufacturing processes that include Semiconductor (Cleaning, Etching and Plating); Chemical Manufacturing, Bio, Pharm, Food Processing, etc.Designed for 6 month continuous operation without operator intervention for minimizing downtime.
-
product
Oil In Cooling Water Monitor
The ability to detect oil in water is important for many industrial processes involving cooling water or heat exchangers. For example, electric generating stations often use natural sources of water such as lakes and rivers to cool generator lube oil systems. The lube oil is cooled in a heat exchanger where the lube oil and cooling water are in isolated streams.
-
product
Thin Film Composition and Thickness Monitor
P-1000
The Precision P-1000 readily analyzes compound thin films utilized in semiconductor, superconductor, magnetic and applications.
-
product
Portable Multi-channel Waveform Monitoring Recorder
MR1200 Series
The portable waveform monitoring recorder is a device for recording and analyzing the change process of electrical signal related parameters of the power system.
-
product
Network Monitor
PRTG
PRTG monitors all systems, devices, traffic and applications of your IT infrastructure using these technologies: SNMP: ready to use and custom options. WMI and Windows Performance Counters. SSH: for Linux/Unix and MacOS systems. Flows and Packet Sniffing. HTTP requests. Any REST API returning XML or JSON. Ping, SQL and many more.
-
product
Torsional Vibration Monitoring Systems
Advanced Telemetrics International
Are used for Noise Vibration and Harshness (NVH) testing and analysis in automotive drivetrain, wind turbine gearbox and various other applications where measuring or monitoring rotating vibration is important. These systems are used to transmit torsional acceleration from a rotating shaft or component, while the machinery is running.
-
-
-
product
Noise Monitoring
Larson Davis provides complete solutions for noise and vibration measurement and analysis. From stand-alone, simple-to-use instruments to complete systems including sensors, data acquisition, and software, Larson Davis has what you need.
-
product
Network Performance Monitoring & Diagnostics SaaS
ObserverLIVE
A subscription-based service which actively assesses end user experience in hybrid environments, to ensure users can effectively access and utilize core business applications. Monitor end user experience on-premises and SaaS based applications.
-
-
product
DC-Powered, Phase Sequence Monitor
PAD/PLD
NAI's PAD and PLD are DC-Powered, Phase Sequence Monitors that protect three-phase loads from damage due to phase reversals or phase absence. These sequence monitors are ideally suited for rugged defense and industrial applications.
-
product
Coastal Monitoring
TZ Coastal Monitoring is a coastal surveillance solution that incorporates FURUNO RADAR with TZ Coastal Monitoring software and systems.With the technical partnership and expertise between FURUNO and TIMEZERO, the Solution provides the best of coastal monitoring for any oil rig, sea farm, port, waterside facility and protected area.
-
product
High Speed Dielectric Cure Monitor
LTF-631
The LTF-631 High Speed Dielectric Cure Monitor is designed for the study of rapidly reacting materials in research and development, quality assurance/quality control, and manufacturing applications involving thermoset materials such as resins, composites, paints, and coatings.
-
product
Network Monitoring Tool
Motadata’s proactive network performance monitoring tool can be used to automatically discover network devices, interfaces, and applications. The network monitoring software in a multivendor IT environment ensures complete visibility of IT infrastructure. The unified view enables IT admins with a comprehensive picture of the overall IT health and also provides drill-down root-cause analysis, enabling them to resolve network issues even before they affect business processes. It facilitates monitoring of hybrid multi-vendor environment using 100+ pre-defined monitoring templates with immediate notifications on the set threshold values.
-
product
Internet Streaming Video Multiviewer Monitoring System
WSM120
Mividi WSM120 is a multiviewer monitoring system designed for monitoring IPTV and Internet streaming video services. It supports most common IPTV and Internet Streaming media protocols including UDP, RTP, HTTP, HLS (HTTP Live Streaming), MPEG-DASH, RTMP, RTSP and MMS.
-
product
TAP Detectors And Power Monitors
The “Premium” jumpers are VZ TPR Certified Cables that provide the highest level of reliability. We also offer the high performance “Standard” jumpers that are Telcordia GR 326 tested and certified. Both the Premium and Standard cables are made in our state of the art manufacturing facility recognized by leading global service providers as one of the best in the industry. We attribute our success to the highly dedicated and skilled production team which starts by selecting only the highest quality fiber and connector components.
