-
product
Video Compression Board
ICS-8580
The ICS-8580 is a standalone video frame capture, compression, streaming and archiving solution in an XMC format making it an ideal solution for demanding video streaming tasks in military and aerospace applications.
-
product
16 Bit PXI I/O Board With 32 Or 64 Analog Outputs
CP266
The CP266 is a single-width, 6U, CompactPCI module with 32 or 64, 16-bit analog output channels. These independent analog channels provide ±10 V full-scale outputs. The channel update rate is 2ms, and each output is accurate to ±1mV. The power-up state of the analog outputs can be set to independent user-defined values. Paired output signals are provided to eliminate ground offset effects. The analog outputs are available at a single 68-pin SCSI II shielded connector (32-channel option) or a pair of 68-pin SCSI II shielded connectors (64-channel option).
-
product
Ethernet to Relay Interface Boards
Model 8064 OEM
* 115631-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully VXI-11 compliant.* Easy configuration with any web browser.* Includes 50-pin mating connector for solder connections.* Optional terminal board for easy connections without soldering. See the Ethernet Accessory page.* Operates on 12 to 24 Vdc power.* Use an ICS Wiring Kit to connect to an RJ45 connector on the rear panel.
-
product
PCI To PCI Express Board
MS 1718
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
product
P104 Synchro/Resolver Simulation Board
73DS2
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
product
Low-cost, Full-Featured Video Frame Grabber Board
Aexeon
DescriptionAexeon is a low-cost, full-featured video frame grabber board for analog camera solutions. Aexeon accepts multiple composite, S-Video, or component video inputs in both NTSC and PAL formats and digitizes in both square pixel and CCIR-601 resolutions. With on-board processing, complete camera control, and video output, Aexeon is the perfect product for analog camera OEM solutions.
-
product
4K Autofocus USB3.1 Gen1 Camera Board (Color)
See3CAM_130
See3CAM_130 is an UVC-compliant AR1335 sensor based 13MP autofocus USB camera with iHDR support. It supports 4K Ultra HD (3840x2160) at 30fps over USB3.1 Gen1 in compressed MJPEG format. This See3CAM_130 can also stream Full HD (1920x1080) at 60fps and HD (1280x720) at 60fps in both uncompressed and compressed MJPEG formats. This autofocus USB camera board is also backward compatible with USB 2.0, although in USB 2.0, this camera supports fewer resolutions at lower frame rates.
-
product
COM Express® Type 6 R3.1 Reference Carrier Board In ATX Form Factor
Express-BASE6 R3.1
Express-BASE6 R3.1 is an ATX COM-Express Type 6 Basic / Compact size module reference carrier board based on PICMG COM-Express Revision 3.1. Together with the COM-Express Type 6 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
3U PXI Express Board Virtex-5 Medium Speed Quad DAC
SMT759
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or SXT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
product
4K Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU135
See3CAM_CU135 is a 13MP fixed focus 4K USB camera board with good low light performance and iHDR support. This 4K board camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux. This 4K board camera is also backward compatible with USB 2.0 host ports.
-
product
VME Single Board Computer
VME Single Board Computers with Intel i7 Core Processor will extend the life of your systems with modern technology.Our popular VME 6U SBC modules feature Intel i7 Core CPUs for high-performance multi-core computing. Multiple front and rear connections for Gigabit Ethernet, USB, and serial ports plus a PMC slot provide great flexibility for high-speed communication and I/O tasks.
-
product
Mixed function mezzanine side card for CPCI-S CPU boards
SCX-PCIE
The SCX-PCIE is a mezzanine side card for EKF CPU boards, equipped with a PCIe® Gen3 packet switch, onboard NVMe and SATA mass storage, and high-speed front I/O.
-
product
Single Board Computers (SBC)
Single board computers in OpenVPX 3U and 6U. VME. 3U and 6U CompactPCI. Intel or Power Architecture. Whatever’s right for your program – and backed by our long term support and technology insertion programs to maximize return on investment.
-
product
Power PC 8641D Based Board
MS 2501
Ethernet Port : 4 Channel (1GBPS)CAN Port : 1 ChannelMIL1553B : 1 Channel (Dual redundancy)RS232 : 4 Channels (512 byte FIFO, 4MBPS)RS422 : 12 Channels (512 byte FIFO, 4MBPS)JTAG : Flash Programming and Debugging
-
product
Squid Carrier Board™ Family PCI Express Gen 3 Carrier Board for 2 M.2 SSD Modules
SKU-086-32
PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 2 M.2 PCI Express SSD modules.PCI Express Carrier board is one-slot-wide, half-height and it compliant with PCI Express Specification 3.0 and M.2 Specification 1.1.
-
product
2.5” Pico-ITX (MI/O-Ultra) Single Board Computers
Advantech's 2.5" Pico-ITX (MI/O-Ultra) single board computer (SBC) measure 100 x 72 mm and feature REAR I/O, fanless operation, small form factor(SFF), compact and ultra slim design, extended temperature range, and low power consumption.
-
product
CPCI-S.0 Standard Compliant Peripheral Carrier Board
MIC-3810
The carrier board provides a PCIe x16 connector for standard PCIe x8, PCIe x4, PCIe x1 PCIExpress® cards supporting PCIe Gen3 speeds. The carrier board can accommodate cards with maximum dimensions of 176 x 68.9 mm (6.9" x 2.7" inches).
-
product
6U VPX Video Processing Board
VP65001
LinkedHope Intelligent Technologies Co.,Ltd.
VP65001 is a 6U VPX video processing board aiming at video overlaying and video enhancing. Designed by LinkedHope®, it is compliant with VITA46.0 and VITA65 VPX specifications. A combination of FPGA+DSP on the board realizes the video processing between 4x 1080P video inputs. Supporting 4 video inputs simultaneously (2x DVI-D, 1x LVDS and 1x PAL), VP65001 can display the processed video through DVI-D or transmit the output through SRIO in the rear I/O to other cards. Through serial interfaces, VP65001 realizes the shift of video overlaying mode, including single channel display, PiP, tiling, etc. In addition, DSP in VP65001 can enhance and process videos by defogging, illuminating, contrast adjusting, etc.
-
product
Digital I/O Board, 64 Optically Isolated Digital I/O Channels,, 5V
APCI-1564-5V
*32 digital input channels, 5V, incl. 16 interruptible*32 digital output channels, 5V, 500 mA / channel*Optical isolation 1000V*Input and output filters*Watchdog, timer*After power/ON the outputs are reset to ì0î
-
product
Digital I/O Board
3512
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
product
Load Board
cPCI 6U
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
product
6U VPX Board
VP62009
LinkedHope Intelligent Technologies Co.,Ltd.
VP62009 is a 6U VPX board based on Intel® Xeon® D-15xx processors, with more than 7-year life cycle. Supporting up to Intel® Xeon® D-1577 (16x 1.3GHz) processor, VP62009 is able to perform vector operation and floating point arithmetic that require high throughput. Besides, VP62009 supports Intel® Turbo Boost, with the processing speed of CPU up to 2.7GHz. The high-performance CPU and the Turbo Boost technology leave no worries for extra cost and complexity of system settings.VP62009 provides 2x 10 Gigabit Ethernet for VPX Data Plane communication, 2 x8 PCIe for VPX Expansion Plane communication, 4 GbE for VPX Control Plane communication. Rich data exchange interfaces on VP62009 make it easy to build box-level or system-level solutions.
-
product
Alchitry Au+ FPGA Development Board (Xilinx Artix 7)
The Alchitry Au+ is the "gold" standard for FPGA development boards and it's possibly one of the strongest boards of its type on the market. The Au+ substitutes a more robust & scalable FPGA chip (Xilinx XC7A100T) that allows for more complex application circuits. The number of Configurable logic blocks (LABs/CLBs), Logic Elements, and total RAM bits are all nearly 3x that of the standard Au; see "Features" for more details.
-
product
6U CompactPCI® Rear Transition Board for MIC-3396
RIO-3316
The RIO-3316 is the first Rear Transition Module (RTM) supporting PCIe connectivity to the main CPCI board enabling significant value-added features and extensions to next generation CPCI blades such as MIC-3396. The RIO-3316 supports: one PS/2 port, one USB 3.0 and one USB 2.0 ports, one RS-232/485/422 ports, two Gigabit Ethernet ports, two PICMG 2.16 LAN ports, one digital and one integrated (digital/analogue) DVI port on the rear panel. One UHM connector on J3 provides PCIe bus and allows supporting USB 3.0 and SATA Gen III (6 Gb/s).
-
product
3U OpenVPX High Density Multifunction I/O Board
68CB6
The 68CB6 is a Configurable Open Systems Architecture™ (COSA®) 3U OpenVPX™ board that is preconfigured with 10 different “inboard” I/O, measurement and communication functions. This Combination-function Board (CB) provides a full suite of some of the most common & useful function interfaces supporting many different applications. The 68CB6 features a wide but dedicated selection of functions: Standard Functionality Discrete I/O (DT1); Successive Approximation Register (SAR) ±100 V Analog-to-Digital (AD); Isolated High Voltage Analog-to-Digital (ADF); ±10 V Digital-to-Analog (DA); Thermocouple (TC1) or Resistance Temperature Detector (RT1); Full-bridge Strain Gauge (SG1); Transmission/gear box Chip Detection and Fuzz Burn (CD1); LVDT-to-Digital linear (LD6) displacement (position) measurement, AC Reference Source output (AC2); CAN bus communication (CB8). The 68CB6 offers unparalleled programming flexibility, a wide range of operating characteristics, and a unique design that eliminates the need for external intermediate circuit considerations such as pull-up resistors or mechanical configuration jumpers. Inboard functions are software controlled and memory addressed, accessed in similar COSA® modular fashion to maintain seamless common NAI Software Support Kit & API/library structures.
-
product
Electronical Load Board 3U VME64x (air cooled)
056-921
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
product
Wireless IoT Solutions, Modules & I/O Board
Advantech provides simple, scalable, efficient transmit features for Wireless IoT Solutions using accurate data acquisition and secure connectivity.
-
product
Training Board
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
product
PICMG 1.3 Half-Size Single Board Computers
PICMG 1.3 half-size Single Board Computers (SBC) suit multiple single board computer requirements. The slot SBC cards offer high speed and wide bandwidth computing platforms, with plug & play, providing flexibility in various industrial applications.
-
product
Multiple Camera Board For NVIDIA® Jetson AGX Xavier™
E-CAM130_CUXVR
e-CAM130_CUXVR is a synchronized multiple 4K camera solution for NVIDIA® Jetson AGX Xavier™ development kit that has up to four 13 MP 4-Lane MIPI CSI-2 camera boards. Each camera is based on the camera module e-CAM137_CUMI1335_MOD, 1/3.2" AR1335 color CMOS image sensor from ON Semiconductor® and integrated high performance Image Signal Processor (ISP). All these four cameras are connected to the base board using 30 cm micro-coaxial cable. These four 4-lane MIPI camera modules can be synchronously streamed in 4K resolution, which will be best fit for high end multi camera solution. Customers can opt to purchase anything between single camera to four cameras as according to their requirement.
