Interconnect Stress Test
accelerated test of PCB pads, lines and thru-holes.
-
Product
Interconnect Adapter, C-Size, Double Slot, 4 Module Positions
510109118
-
Interconnect Adapters funnel wiring from modules to a VXI card. The adapter has removable side, top and bottom plates. Connector cover plates and cable clamps are ordered separately.
-
Product
Highly Accelerated Stress Test Chambers
HAST
-
Our HAST systems have a modern design that's easier to use: Automatic humidity filling; Automatic door lock; A more square workspace; allowing more product to be loaded;Convenient, hermetic power-pin system for bias testing. We are now able to offer a hermetic port system to allow special signal lines like coax or fiberoptics to be run into the chamber.
-
Product
ARINC-429 Module
M4K429RTx
-
The M4K429RTx is an ARINC-429 multi-channel test and simulation module to be used on the Excalibur 4000 family of carrier boards. The module supports up to ten ARINC-429 channels in any combination of transmitters and receivers. Each of these channels feature error injection and detection capabilities. The receive channels allow for the storage of all selected Labels with status and time tag information appended to each word.
-
Product
Flexible Cable, 2.4 Mm To 3.5 Mm
85134H
-
The Keysight 85134H is a 62.9 cm (24.75 in) long1 flexible cable with a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2 (where f is frequency is GHz) for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 2.5 inch radius. Stability1 of the Keysight 85134H is less than 0.12 dB and phase is less than 0.13o * f + 0.5o, (where f is frequency in GHz).
-
Product
Test Port Adapter Set, 3.5 Mm (Test Port) To Type-N
85130C
-
The Keysight 85130C test port adapter is designed to protect the test set port when it would be directly connected to the device under test. These adapters have a special rugged female connector designed for connecting to the network analyzer test port. This special connector will not mate with a standard male connector, but converts the rugged test set port to a connection that can be mated with the device under test. The set contains a 3.5 mm to type-N male adapter and a 3.5 mm to type-N female adapter. The frequency range for these adapters is dc to 18 GHz with a return loss of 28 dB or better.
-
Product
Wafer-Level Parametric Test
-
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
Attenuator Interconnect Kit, SMA
11716C
-
The Keysight 11716C quickly and conveniently connects 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716C can be utilized to connect any of the two Keysight 8494/95/96 attenuators in series.
-
Product
Flying Prober Test System
QTOUCH1404C
-
Qmax Test Technologies Pvt. Ltd.
The Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built high resolution Vision Camera for easy monitoring of probe needle contact. The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision.
-
Product
Bow and Global Film Stress Measurement
128 Series
-
Bow and Global Film Stress Measurement.Non-contact full wafer stress mapping for semiconductor and flat panel application.Dual Laser Switching Technology.
-
Product
Cable Assemblies for Interconnect Solutions
-
High quality connectors are just the beginning. Circuit Assembly (CA) also has over three decades of experience in producing a wide variety of cable assemblies for various applications. CA has the technical and manufacturing capabilities to provide customers with high-quality and cost-effective cable assemblies tailored to meet their needs. Circuit Assembly utilizes a quality process recognized by ISO 9001, and CA's cable assemblies are UL/CSA certified.
-
Product
Plant Stress Kit
PSK
-
The Y(II) meter was designed to provide an inexpensive way to measure the fast light adapted Y(II) or F/FM' protocol and to make it available to more people that need it.
-
Product
Automated Aerospace and Defense Test
-
Obsolescence management, evolving RF requirements, and design for test (DFT) challenges every test organization in the aerospace and defense industry. Organizations are transitioning from rack-and-stack box instruments and closed-architecture automated test equipment (ATE) systems to smarter test systems built on a modular platform that scales to meet current and future needs.
-
Product
In-Line RF Test Station
AP770
-
ICT, Functional, Hipot, Vision, ISP and RF test with low cost fixtures in a very compact test station footprint Works with PCBs up to 450×550 mm or with palletized devices Space for up to 25 VPC mass interconnect modules or YAV switching units
-
Product
Spring Clip Fixture
16092A
-
Use this test fixture with parallel electrodes for impedance evaluation of both lead and SMD components.
-
Product
RF Coaxial Interconnect System VPX Compatible Rectangular Harness Solutions
VITA 67 Rectangular Harness
-
VITA 67 is a VPX standard for blindmate coax connectors that allows high density, high performance RF connections to be made between a backplane and plug-in modules.
-
Product
High Volume Semiconductor Substrate Interconnect Tester
GATS-2100
-
Pre-align *load *CCD camera alignment *electrical test * unload * sort of pass, opens, shorts, and alignment errors.The GATS-2100 concurrent approach provides unmatched volume capability... 2.5 seconds per device. As with all Nidec-Read Test systems, the GATS-2100 offers you the most test technologies for your requirements
-
Product
Parametric Test Fixture
U2941A
-
The Keysight U2941A is a parametric test fixture that is designed to complement the usage of U2722A USB source measure unit in the testing of semiconductor components, including SMT and DIP ICs.
-
Product
Functional Test for Engineering Lab
Spectrum BT
-
Designed to meet the needs of product engineering labs, production lines, test development centers, and repair depots, the Spectrum BT is a configurable and scalable functional test system. This focused system solves typical functional test coverage challenges throughout the defense/aerospace product life cycle—and it’s upgradable as test requirements evolve.
-
Product
Labratory Micro-Spot XRD Residual Stress Analysus with both Iso- and Side-Inclination Methods
AutoMATE II
-
Residual stress may be created during the manufacturing process of a material, or it may accumulate in a structure over many years in operation. In either case, this stress can have a serious negative effect on a product's quality, durability and lifetime. Accurate detection of residual stress is an important element of the quality control process and helps predict the service lifetime of products.
-
Product
SoC Test System
T2000
-
SoC devices require small-lot high-mix manufacturing methods in the present era of rapid generation change. Semiconductor makers struggle with requirements to replace their testers on a 2-3 year cycle. The T2000 addresses their needs by enabling rapid response to market needs with minimum capital investment.
-
Product
Shear Stress Sensors
DirectShear™
-
Micromachined floating element shear stress sensor that enables time-resolved, one-dimensional, direct shear stress measurements. Direct measurement of shear stress — no heat transfer calibration. Non-intrusive — minimal flow disturbance. Simultaneous mean and fluctuating shear stress measurements. High resolution, dynamic range and bandwidth. Highly accurate, quantitative measurements.
-
Product
Backgrinding & Stress Relief
-
Grinding and Dicing Services, Inc.
GDSI delivers complete backgrinding solutions to the semiconductor, MEMS and biomedical industries. Backgrinding is a necessary process step to reduce wafer thickness prior to dicing and final assembly. By utilizing fully automated grinders staffed by highly qualified engineers, GDSI’s grinding procedures produce unsurpassed precision and repeatability.
-
Product
Automated Thermal Stress System
ATSS Series
-
Thermotron's Automated Thermal Stress Systems (ATSS) facilitate extremely rapid product temperature change rates in a space-saving, self-contained design that accelerate a Thermal Stress test. Thermotron's ATSS chambers meet the latest MIL-STD 883E and MIL-STD 202F thermal shock specifications as well as JEDEC and IPC test methods. ATSS chambers are capable of the following: Rapid thermal shocking, Accelerated product stressing, Controlled thermal cycling in a self-contained, compact design. With separate hot and cold zones, the Automated Thermal Stress System was designed with a patented retractable product transfer carrier that makes full use of the available working volume in both temperature zones for increased product loading and throughput. The product transfer carrier reduces the overall height requirements of the chamber and is made as light as possible to minimize thermal loading restraints. Thermotron ATSS chambers can be used as part of most commercial reliability and quality control programs, helping to determine:
-
Product
Mass Interconnect
-
Mass interconnect is a way of connecting test instrumentation to a device under test (DUT). To put it simply, mass interconnect is a very large plug and socket which connects your device under test to your test instrumentation without the mess and hassle of having to connect each signal separately.
-
Product
Fixturing Kit
10744A
-
The Keysight 10744A fixturing kit includes mounting hardware for a variety of Keysight measurement optics devices. A large base, multiple posts, and other accessories let you build structures -- such as tall, rigid towers -- that place optics in the center of a machine's work zone or wherever needed. The fixturing kit helps meet the physical requirements of a range of measurement applications.
-
Product
Memory Test System
T5833/T5833ES
-
T5833 system is a cost-efficient, high-volume test solution capable of performing both wafer sort and final test of DRAM and NAND flash memory devices. Amid surging sales of mobile electronics, DRAMs, NAND flash memories and multi-chip packages (MCPs) — the main device types used in smart phones and tablets — are quickly evolving toward higher speeds and greater device capacity. Internet and cloud servers also are driving demand for faster, higher-capacity ICs. Yet the cost of testing today's wide array of memory devices is an obstacle for chipmakers, which urgently require solutions that can deliver high functionality, high performance and low cost of test (COT). Advantest's new, multifunctional T5833 memory test system meets these needs, delivering both wafer sort and final test capabilities for a full range of memory devices, including LPDDR3-DRAMs, high-speed NAND flash memories and next-generation non-volatile memory ICs.
-
Product
Photodiode Burn-in Reliability Test System
58606
-
The Chroma 58606 PD/APD Burn-in system is a high density, multifunction and temperature controlled module based system for photo diode burn-in and lifetime test. Each module has up to 256 Source Measurement Unit channels which can source current and measure voltage in various scenarios such as one described below. The system can accommodate 7 modules for a total of 1,792 device channels.
-
Product
Interconnect Adapters
-
Interconnect Adapters funnel wiring from modules to a VXI card. The adapter has removable side, top and bottom plates. Connector cover plates and cable clamps are ordered separately.VPC VXI adapters have been re-engineered to eliminate the need for punching holes in certain manufacturers cards. This design uses a clip that clamps down on the card's existing ejector tabs which firmly fastens the adapter to the card.
-
Product
Fixture Kit 600x455mm RCV 8-slot for 6TL34
AG588
-
Stopper kit includedYAVCANCON2 for fixture identification not included
-
Product
At-Speed Non-Intrusive Functional Testing
ScanExpress JET
-
Functional circuit board testing presents many challenges that are often costly and time consuming. Most functional tests need to be customized for each design, limiting reusability. This results in software engineers vying for time between development code and test code. Even when functional tests become available, the diagnostic details are often inadequate to give clear visibility on a given problem.ScanExpress JET is a tool designed to overcome these challenges by automating the functional test generation process on CPU–based IEEE-1149.1 compliant circuit boards. Coined JTAG Embedded Test, JET is the preferred method for at-speed, non-intrusive functional testing.
