Single Phase
A single alternating voltage.
-
Product
Advanced Line Protection System
ALPS
-
ALPS is a multi-function digital protective relay system intended toprovide distance protection for HV or EHV transmission lines. It maybe applied on or adjacent to series compensated lines. It is availablefor single or three phase tripping applications. Typical operatingtimes are to 1 cycle.
-
Product
Programmable AC Power Source
LSX Series
-
The LSX Series consists of a range of fully featured, single and three phase AC Power Sources. Available models range from 1.5kVA to 6kVA with an advanced programmable controller sporting a color touch screen user interface. Cost effective and fully programmable for both basic frequency conversion as well as advanced AC power line disturbance test and ATE applications. For applications not requiring advanced features, a basic function set M version of the LSX is available as well.Note: The LMX Series is not CE marked yet at this time.
-
Product
NI-9244, 400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module
783106-01
Voltage Input Module
400 Vrms L-N, 800 Vrms L-L, 50 kS/s/ch, 24-Bit, 3-Phase C Series Voltage Input Module - The NI‑9244 performs single-ended analog input. The wide measurement range makes it ideal for high-voltage measurement applications such as phasor measurements, power metering, power quality monitoring, industrial machinery, and motor test. You can also perform transient and harmonic analysis with high-speed simultaneous sampling. The NI‑9244 offers three channels, so you can connect single‑ or three‑phase measurement configurations such as WYE and delta. You can incorporate the NI‑9244 into systems to meet standards such as IEC 61010‑1, C37.90 and C37.60, IEC 60255‑22‑(1:7), IEC 60255‑1, C37.188 Class M and P, EMC section of IEC 60870, EMC sections of IEC 61850, IEC 61000‑4‑30 Class S, and IEC 61000‑4‑7.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
Low Voltage Single Phase
600V Class
-
These transformers are encased in a thermoplastic case with the core and windings encapsulated in resin. They are designed for line-to-line operation but may also be used in line-to-neutral or line-to-ground configuration at 58% of rated voltage. It is recommended that a 1.6 Amp fuse be used in the secondary to protect the transformer.
-
Product
Power Monitor, AC- or DC-Powered
109
Power Monitor
NAI’s 109 is an AC- or DC-Powered Power Monitor used to monitor voltage, frequency, and phase characteristics of single- or three- phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.The 109 monitor provides three separate control circuits and output relays indicating the condition of each line characteristic. It is ideally suited for rugged defense and industrial applications.
-
Product
DC POWER
VARIABLE TRANSFORMER
-
Variable DC power supplies are AC to DC power supplies with a variable DC output. The output can be varied with a Variable Transformer (also known as variac). The Variable Transformer can be adjusted manually or with a motorized control. The AC input power can be single phase or three phases. With single phase AC input, the DC output ripple is very high (50%). With three phase AC input, the DC output ripple is low (5%). This would be a key benefit for selecting three phase AC input instead of single phase.
-
Product
Relay And Protection Testing
-
As the first protection relay test set manufacturer in China, PONOVO has been always offering reliable protection relay testing equipment for customer for more than 20 years. More than 20,000 relay test kits has been supplied to users in China and other countries, including 6-phase, 3-phase, single phase relay test sets, capable of testing all kinds of protection relays, from electromagnetic relays, solid state, numerical, microcomputer relays and digital relays based on IEC61850 as well as other testings, such as, energy meter, transducer, etc. With various models with different specifications, users can definitely choose the model suitable for their testings.
-
Product
Portable AC/DC Power Supply
UPS S3
-
The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.
-
Product
Digital Line Protection System
DLPD
-
The DLPD provides distance protection for HV and EHV transmission lines. It may be used for single or three phase tripping applications. It includes four zones of distanceprotection. User selectable pilot schemes are provided with stepdistance backup. Ground instantaneous and time overcurrentfunctions are independently selectable to be directional ornon-directional.
-
Product
Meter Test System
MTS-50
-
Kongter Test & Measurement Co., Limited
This meter test equipment features state-of-art designing with high accuracy. It is composed of high accurate (class 0.05% or 0.1%) standard reference meter and power source (up to 50A). This system is particularly designed with modular structure for calibration and test of different single phase/3 phase electronic/inductive active and reactive energy meters.
-
Product
Utility Card: Flash Programming Applications
-
This new feature enables the Keysight Medalist i3070 ICT to perform higher speed flash programming at the ICT station in the printed circuit board assembly manufacturing line. You can combine programming and testing into a single phase, to save time and money. This in-system programming (ISP) flash solution is tester-based and does not rely on fixtures, thus enabling greater flexibility and ease of debugging.
-
Product
Power Bead Inductors
-
Power bead inductors are typically used in high current multi-phase voltage regulators that power processors, memory modules and high current ASICs and FPGA in a wide range of applications including servers, graphics cards, storage and data centers. The construction consists of a ferrite core assembled over a 1T or 2T winding and which allows for extremely low DCR, high peak current and low AC losses. Pulse has single phase, integrated phases and coupled inductor versions. Our high volume manufacturing enables us to produce components that are cost-effective while maintain exceptional quality and reliability.
-
Product
Energy Analyzer
EP600i
-
The EnergyPro EP600i is portable and easy to use. Perfect for single phase or three phase energy consumption analysis and basic power quality monitoring. It supports standard wiring configurations and comes with a set of 1A - 2500A WideRangeFlexCT ™. The graphics display makes setup very easy and intuitive - you can setup and record data without looking at the manual!
-
Product
Power Transformer
-
Transformer turn ratio meter is special designed for power transformer (single phase & three phases) and instrument transformer testing, suitable for testing in substation, transformer manufacturer, meter manufacturer. It helps to detect faulty transformer winding and tap changer position. It’s fully automatic device, can recognizes winding connection and vector group number of transformer winding. The user only need connect measuring cable and press start button and come out the test result.
-
Product
Voltage Dip, Interruption& Variation Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
PFS single phase power fail simulator simulates voltage dip, interruption and variation which are caused by power grid and transformer devices due to malfunction or sudden large change of load. It is required to test this kind of phenomena to check whether electronic and electrical device can sustain safety operating condition.
-
Product
Multifunction Power Meter (DIN rail)
CPM-12D
-
CPM-12D is a din rail mounting multifunction power meter with high accuracy measurement for single phase and three-phase system.Measuring all basic parameters ; V, I, P, Q, kWh, kVarh etc..
-
Product
Electro Fatigue Testing Machine
EPS Series
-
Jinan Testing Equipment IE Corporation
EPS series Electro Fatigue testing machine are fast acting table-top testers ideally suitable for performing static and dynamic fatigue tests on a variety of materials and components. These electro-dynamic machines use a linear electric motor with an adjustable upper cross-head of a stiff dual column frame. The electro-dynamic actuator is connected to single phase power, which resulting in a clean low maintenance solution. With dynamic force capacities, the Electro Fatigue testing machines are used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastomeric materials and others.
-
Product
Digital Power Recorder
MPR-601W-01
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Applicable for single phase 2wires and single phase 3wires and *3phase 3wires and 3phase 4wires system*Wide measuring range up to 0～500V/500A*Easy data logging by USB flash memory
-
Product
Electricity Metering Device Residential
NC30
-
EDMI presents its single phase multi-tariff ANSI meter, the NC30. The ANSI compliant meter is designed to supply a comprehensive portfolio of revenue-grade features. NC30 has the ability to render an optional disconnect function and has the competency to offer multiple communications option. It has also the capability of storing meter data up to 12 months of its history.
-
Product
High Performance Power Analyzer
AFM-8A
-
AFM-8A has Developed for AFC*(Auto Frequency Control) high performance measurement and frequency update, its update up quickeer than 100mSec. multifunction power analyzer provides high-accuracy measurement and is designed for single phase and three phase application. It includes 4 Digital inputs, 4 Relay outputs, and a RS-485 Modbus RTU Communication port. The user can choose one more communication port, and 2 Analog outputs for output expansion.It provides measure voltage and current of the 2~63 harmonic, and it shows CO2 emissions, which is suitable for power monitoring, management and analyze power quality. It has TOU (time-of-use) function and 4MB Flash memory capacity, allowing users to record data for a long time. It also has a software line adjustment function to reduce the on-site line adjustment work.It has the functions of waveform capture and recording, power record, and event record, which can be used for multifunction power analyzer.
-
Product
Three-Phase Relay Tester
PTE-300-V
-
The equipment compromises of three independent output channels than can be selected as voltage or current. This enables the unit to be used as a complete single-phase equipment (Voltage, Current, and phase angle between them), or with channels synchronized, as a three phase voltage or three phase current generator from a single phase mains input. The unit is extremely compact and rugged. The design incorporates the latest in modern digital microprocessor technology to achieve unbeatable output characteristics in terms of power, accuracy, low distortion, and dynamic capability.
-
Product
Single-Phase Meter Test Equipment
ASTEL 1.2 TYPE
-
ASTeL 1.2 meter test equipment is a fully automatic system that enables simultaneous, multi-position calibration and verification of single-phase electric energy meters. ASTeL 1.2 offers full compatibility with IEC 60736. Thanks to excellent parameters, superior functionality and outstanding flexibility, ASTeL 1.2 is an ideal solution for utility companies, energy meter manufacturers, governmental institutes of metrology, metrological laboratories, and other customers interested in electricity meters testing.
-
Product
Primary Current Injection Sets
-
Protective devices such as relays, overload Coils, Circuit breakers and CTS etc. must be checked regularly to ensure that they are always ready to operate correctly, Routine current injection testing will quickly detect faulty or incorrectly adjusted protection circuits / devices & will be possible to prevent serious damage to the system. Primary injection kit is designed to operate on single phase 230/240 volts AC 50 HZ to develop smooth & continuous test current as for loading, calibrating, and testing of CTS, Bimetal Relays, Protection Relays etc. The test set gives high current output at low cost and with inherent safety. The primary current injection testing checks all parts of the protection system by injecting current down the cable / bus bars. The application of the primary current injection sets is to ascertain the current carrying capacity of any Conductor, insulator, connector or calibration of CTS / Bi-metallic relays etc.
-
Product
Single-Phase Power Meters
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
An electricity meter, electric meter, electrical meter, or energy meter is a device that measures the amount of electric energy consumed by a residence, a business, or an electrically powered device.
-
Product
EMC Compliance Test Systems
ECTS2
-
Now in its second generation, the ADAPTIVE POWER EMC Compliance Test Systems use a greatly enhanced harmonics and flicker measurement system and newly designed flicker impedance options to support single and three phase AC harmonics, flicker and AC and DC immunity compliance testing up to the maximum required current of 75A per phase.
-
Product
Digital Panel Meter
-
Our product range includes a wide range of Digital Volt-Amp-Watt Meter (DVAW-1.), Digital Voltmeter. (DTV-1), Digital Voltmeter, Digital Wattmeter, Digital Single Phase True Voltmeter. and Digital Frequency Meter. (DTF-1).
-
Product
Automatic Asphalt Content Tester
-
4000g sample capacity, integrated +0.1gm accuracy weighing scale, High temperature ceramic filtration system and afterburner for accurate measurement of bitumen content in asphalt mixes. Automatic operation through user defined automatic end point detection and 24 hour start timer. User defined control of furnace chamber temperature from 200 – 650oC, Digital display and printing of test data through bright LED displays and integrated printer, Software activated mechanical door lock to prevent door from opening during test process and cutting off power from the heating elements upon opening the door. Operates on Single Phase, 220V, 50 Hz, 20 Amp and consumes less than 5000 W.
-
Product
AC Power Supply
LSP-500VAS
-
AC-DC-AC frequency conversion technology, Controlled & tested by 16 bits MCUProtection for over hot, thundering voltage and currentTotal voltage distortion: ≤0.6%; Voltage stability: ≤0.1%/30minDownloadOutput voltage range: AC 0.0~300.0V, Output Frequency Range: 45~70Hz, 100Hz, 200Hz and 400HzInput Power: single phase 220V and 50/60Hz (other input spec can be option)Communicate with PC via software, the Voltage & Current set by the software and Power Output can be remote controlled.
-
Product
Single Phase Din Rail Multi-Tariff Energy Meter Type DDS999D
-
Bofa Instrument & Equipment Co., Ltd
Single phase Din rail multi-tariff energy meter type DDSF999D is a new type of single phase electronic multi-rate energy meter, which accords international standard IEC61036. It features: good reliability, small volume, light weight, convenient installation, etc.
