Burn-In Sockets
See Also: Test Sockets, Burn-In, BGA Test Sockets
-
Product
Test Sockets
-
Yamaichi Electronics Co., Ltd.
A test socket is the ideal point to test your home’s internal phone wiring for faults. You can also use it to identify any potential faults with the phone line outside. Your test socket is located in your master socket. It is the point between the internal phone wiring in your house and the phone line outside. That means by plugging into your test socket you can bypass all the internal wiring and test your device directly on the phone line.
-
-
Product
Standard DIP Socket with Solder Tail Bifurcated Contacts
Series 511
-
Standard DIP Sockets with Wire Wrap Bifurcated Contacts. Features: Standard DIP sockets are available with solder tail or wire wrap pins, all with bifurcated contacts. Consult Data Sheet No. 12005 for wire wrap pins. Aries offers these standard DIP sockets in more sizes than any other manufacturer.
-
-
Product
Elevator Socket with Bifurcated Contacts
Series 8XXX
-
Elevator Sockets with Bifurcated Contacts. Ideal for elevating devices (displays, switches, etc.) to desired level with .260 to 1.250 [6.60 to 31.75] height extension.
-
Product
LGA Sockets
-
We’ve taken our QFN expertise and combined it with the versatility and performance of the H-Pin® to leverage an LGA socket platform that serves the demanding requirements of today’s market. Plastronics LGA sockets using the H-Pin provide a high-performance socket that is affordable for all burn-in operations. These LGA sockets meet the power, temperature and signal performance needs of the higher density, larger package outline, and sometimes mix-pitch LGA designs. The LGA platform serves package sizes from as small as 2.0mm X 2.0mm to the industry’s largest standard socket for 60.0mm X 60.0mm packages.
-
Product
Burn-in Room and Aging Test Chamber
-
Aging test room according to your requirements. More types of Burn-In Test Room, Burn-In Chamber, Burn-In Test Oven wanted, please contact us freely.
-
Product
TEST SOCKET
-
IC Package It is a device to install INTERFACE between TESTER and DEVICE during TEST to check electrical defects such as O / S (Open, Short) test, mounting test, BURN-IN TEST and RLC TEST, The device
-
Product
Socket Wrench Torque Sensor Reaction Type
SWS SERIES
-
Our SWS Series reaction type socket wrench torque sensors are available in ranges from 10 ft-lbs. through 1000 ft-lbs. and provide accurate measurements of bolt or nut wrenching torques. These sensors are bi-directional so both tightening and break-away torques can be measured. These low cost sensors deliver high accuracy and outstanding frequency response. alibration of mechanical torque wrenches may be performed with this sensor. The sensing element incorporates bonded foil strain gages of the highest quality.
-
Product
Smart Sockets
-
Ironwood Electronics extended its high performance socket product line with smart features. Sockets are typically rated for 2K to 500K cycles. How do we know if the sockets are used for 100K or 200K insertions? Solution is electronic chip insertion counter. Our sockets can be integrated with electronics counter into the compression mechanism of the socket lid. A push button is exposed on the compression plate. Every time a chip is compressed, push button is actuated which in turn activates the electronic circuitry inside the lid. These activations are counted by the counter IC and displayed in LCD. Let’s say a contact element is rated for 2K insertions. After 2K insertions, this contact element will be replaced by new contact element. Now, the counter has to start the counting from the beginning. To achieve this function, a reset option is included in the electronics circuitry. When reset is actuated, LCD display will go to “0”.
-
Product
Memory Burn-In Tester
H5620/H5620ES
-
H5620 contributes to reduction of test cost by integrating the test process of DRAM Burn-in and Core Test. This hybrid memory test solution solves the challenge of reducing test costs while increasing test efficiency in the expanding DRAM market.
-
Product
Burn-In Systems
OPTIMUM Series
-
Advanced Microtechnology, Inc.
The OPTIMUM product line of burn-in systems has a model to meet your individual testing requirements. Please select one of the models below for more specific information
-
Product
Socket Wrench BIT731S1
1007605
-
The BIT731S1 is a specialized tool designed for precision tasks within the category of threaded probes, prominent in the field of mechanical engineering. This socket wrench measures a compact 1.40 mm in tool size, ensuring adaptability for various intricate applications. With a total length of 67.50 mm and an outer diameter of 2.40 mm, it is engineered for efficiency, allowing for enhanced maneuverability in tight spaces while maintaining a robust structure.
-
Product
Strip-Line™ Socket with Bifurcated Contact Wire Wrap Pins
Series 0501
-
Strip-line Sockets with Bifurcated Contact Wire Wrap Pins. Features: For mounting liquid crystal displays and other high pin count or odd centered components. Available in several sizes with bifurcated contacts in wire wrap or solder tail pins. Consult Data Sheet No. 12008 for solder tail pins.
-
-
Product
GFCI Socket Tester
ST120
-
The Fluke ST120 GFCI Socket Tester checks that each wire in the outlet is properly connected to the building's electrical system. Via the bright LEDs and included chart, you can quickly and easily verify the wiring of an outlet. Able to identify several common wiring errors, including reversed phase and neutral wires and an open ground, the ST120 will give you confidence on your next job.
-
Product
Burn-In Test Fixtures
-
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
Product
IEC60884-1 Plug Socket Switch Life Tester With 3 Stations
CZKS-4
-
Shenzhen Chuangxin Instruments Co., Ltd.
1. This test equipment is designed and manufactured according relevant requirement of Standard IEC60884-1,GB2099.1 and GB16915.1,Mainly used to test the service life of household and similar use plugs and sockets or switches. 2. This machine connect to load cabinet and conduct electrical life test ,normal operation and breaking capacity to plug socket and switch.
-
-
Product
DIP-to-JEDEC TO Adaptor Socket
1109522 & 1109523
-
DIP to TO Adapter Sockets. 8 pin DIP IC socket on the top and a circular, 8 pin TO can male pin footprint on the bottom. ICs now available only in 8 pin DIPs can be readily mounted on boards having TO thru-hole footprints without having to redesign the board.
-
Product
Meter Socket Logger
PM2000
-
The PM2000 Meter Logger (USA only) is a 5-channel data logging system built into an electric meter housing. It is ideal for responding to residential voltage complaints and power consumption problems.
-
Product
GHz Elastomer Sockets
-
Ironwood’s GHz BGA & QFN/MLF sockets are ideal for prototyping and testing almost any BGA or QFN device application. These ZIF sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss up to >40GHz and supports BGA or QFN/MLF pitches down to 0.3mm was utilized in these sockets. GHz BGA sockets are mechanically mounted over a target system’s BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry’s smallest footprint). They support IC devices with body sizes ranging from 55mm down to 1mm. Larger body sizes may require a backing plate. If the backside of the target PCB contains capacitors and resistors, a custom insulation plate with cavities cut for those components can be designed. This insulation plate sandwiches between the backing plate and target PCB.
-
Product
Memory Burn-In Test
-
The N3500 is Neosem Technology’s fourth generation memory test system. Specifically designed for Flash Components and Flash Cards, the N3500 tester-on-a-board architecture targets the broadest range of DUT technologies in various form factors and packages. Each Tester Board (or “Blade”) contains 288 I/O pins and 32 DPS supplies.
-
-
Product
ZIF (Zero-Insertion-Force) Socket
Series 516
-
Zero Insertion Force Socket. A choice of 24, 28, or 40 pin count devices can be inserted without bending or otherwise damaging the legs, since no force is required to either insert or remove the component from the socket. Contacts are normally open and are closed by a unique cam action controlled by dual lever arms. The last 15° of movement of the cam provides a wiping action to the contacts on the legs of the device to remove any residue, ensuring a gas-tight seal.
-
Product
DU Sockets
445012
-
DU bushings are rolled dry sliding bearing bushings and also serve to properly guide the guide pins into the pin carrier plate.
-
Product
Socket Wrench FWZ348T
1031601
-
The FWZ348T is a versatile tool designed for precision work in various applications. Primarily categorized under tools and equipment, particularly as a threaded probe, this socket wrench exemplifies durability and efficiency. With a compact tool size of 6.00 mm and a total length of 100.00 mm, the FWZ348T is engineered to facilitate intricate tasks while ensuring user comfort and control. Its outer diameter of 7.60 mm allows for easy access in tight spaces, making it an essential addition to any toolkit.
-
Product
Burn-in Environmental Test Chamber
-
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell's High Temperature Aging Chamber is widely applied for automotive parts ,electronic and electric products ,components and materials by constant high temperature reliability test.
-
Product
Pin-Line™ Collet Socket with Wire Wrap Pins
Series 0503
-
Pin-Line Collet Sockets with Wire Wrap Pins. Features: Rows of socket strips may be mounted on any centers and are end-to-end or side-by-side stackable for .100 [2.54] grid or matrix patterns. Available with wire wrap or solder tail pins. Consult Data Sheet No. 12013 for solder tail pins. Break feature allows strips to be cut to the number of positions desired.
-
Product
4G Concurrent Device Programmer for PC /USB (4 sockets)
ProMax 4G
-
ProMax is the most innovative and cost effective 4- or 8-gang programming solution on the market. ProMax supports a wide variety of programmable devices. Its state-of-the-art technology and high-speed programming algorithms optimize throughput, reliability and yields.
