Passive Optical Network
Optical transmissions requiring no electrical power or active electronic parts.
-
Product
Network Analyzer, Tester, LED
72-9450
-
This cable tester allows for quick and easy troubleshooting of RJ45 and USB cables. Checks for continuity, faulty wiring, open, shorts, straight through or cross pinning of cables.
-
Product
CATV Fiber Optic 1550nm Transmitter
T8500HC Series
-
The MX-T8500HC series externally modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital signals from 50-862 MHz for CATV applications.
-
Product
Real-time IP network measurements
IPProbe
-
Real-time network measurements for multiple IP interfaces. Detection of Packet loss, IAT (Inter Arrival Time), Delay, Bitrate and ETR290 problems. Stable packet generation and receiving is a key feature required in any modern IPTV environment. Any irregularity and/or discontinuity in this packet stream means buffering problems or losing frames. IP jitter provides a means to see the distribution and stability in the IP stream.
-
Product
Network Analyzer, Lan Tester, LED
72-6706
-
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
Product
Fiber Optic Accelerometer
MR660
-
The MR660 Series Accelerometer provides an innovative solution to measure vibration and movement in high voltage or ATEX environments. The MR660 Accelerometer system employs a highly sensitive MEMS membrane to provide a robust system capable of producing an output signal of 100mV/g pk-pk.
-
Product
Network Impairment Simulator
-
Testing system performance under realistic network conditions requires the introduction of impairments that could be expected to be seen on networks, especially public networks which are uncontrolled. There are a number of ways to do this. A basic method is to use network simulation devices that can emulate conditions expected to be encountered.
-
Product
Laser and Optics Case
E1734A
Accessory Kit
The E1734A is a heavy duty transport and storage case which houses a basic 5530 Laser Calibration System plus additional space for other components (except tripod and rotary measurement kit). The case has integrated wheels and handle for ease of moving around. Provision for padlocks for added security is available.
-
Product
T3DSO Passive Probe, 350 MHz, 10X, 10 MOhm, 300V/600V
T3PP350A
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
CNC Machine Network Solution
WebAccess/CNC
-
Webaccessoryess/CNC supports diverse SCADA drivers, CNC, I/O, PLC devices for efficient equipment data collection & networking app development.
-
Product
Plastic Optical Power Meter
POFPM100
-
Shanghai Tarluz Telecom Tech Co., LTD
POFPM100 POF OPM used for the plastic optical fiber within 600 ~ 1000nm wavelength range, w, dBm units, five calibration wavelengths.
-
Product
PXI Dual 2 Channel Fibre Optic LC
40-855-422
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
47~862MHz Four outputs FTTP CATV optical receiver
P9428
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai P9428, the operating bandwidth of 47 ~ 862MHz, is a low power, high performance, cost-effective triple play, FTTH CATV optical receiver. Products with high sensitivity optical receiver tube and Huatai special low noise matching circuit..
-
Product
PXIe-5633, 26.5 GHz PXI Vector Network Analyzer
790406-12
Vector Network Analyzer
The PXIe-5633 is a single-slot PXIe Vector Network Analyzer (VNA) that helps you streamline your production test applications. This VNA supports automatic and manual precision calibration, full vector analysis, de-embedding, and pulsed S-parameter capabilities, making it ideal for validation and production operations without the high costs and large footprints associated with traditional benchtop VNAs. The PXIe-5633 also integrates into NI RFmx and Instrument Studio software to provide automated control for test program development. Additionally, the PXIe-5633 features a hardware pass-through path that you can use for PXI Vector Signal Transceivers (VSTs) testing directly at the VNA ports. With combined modulated and S-parameter measurements on a single connection, you can cover both VST and VNA tests on a single device.
-
Product
MIL-STD-1553 Data Acquisition Module for Ethernet Networks
eDAQ-1553
-
Avionics Interface Technologies
One or two dual redundant MIL-STD-1553 bus interfaces - Transformer and Direct bus coupling supported - Two 10/100/1000 Mbit/s Ethernet LAN Interfaces - Streams MIL-STD-1553 bus data in standard IRIG 106 Chapter 10 format. - Compatible with 3rd party recorders and telemetry tools - All captured MIL-STD-1553 bus data provided with timestamps - Full error injection & detection capabilities - Works with AIT’s Flight Simulyzer™ GUI Analyzer/Simulator software
-
Product
Backlight Module Optical Measurement System
-
RayClouds Photoelectric Technology Co.,Ltd.
The DM series backlight module optical characteristic automatic measurement system is equipped with photometer, colorimeter and spectroradiometer to measure the luminance and chrominance, uniformity of the backlight module.
-
Product
Optical Talk Sets
-
Talk sets in fiber optics are used as a communication device in the installation, activation, and repair of optic fiber networks. The talk sets offered through GAOTek are high quality, easy to use, and ruggedly built so you know they’ll be reliable no matter the conditions your field work is in.
-
Product
Optical Fiber Cable Testing Equipment
-
Optical fiber consists of a core and a cladding layer, selected for total internal reflection due to the difference in the refractive index between the two. In practical fibers, the cladding is usually coated with a layer of acrylate polymer or polyimide. This coating protects the fiber from damage but does not contribute to its optical waveguide properties. Individual coated fibers then have a tough resin buffer layer and/or core tube(s) extruded around them to form the cable core. Several layers of protective sheathing, depending on the application, are added to form the cable. Rigid fiber assemblies sometimes put light-absorbing ("dark") glass between the fibers, to prevent light that leaks out of one fiber from entering another. This reduces cross-talk between the fibers, or reduces flare in fiber bundle imaging applications Optical fibers are very strong, but the strength is drastically reduced by unavoidable microscopic surface flaws inherent in the manufacturing process. The initial fiber strength, as well as its change with time, must be considered relative to the stress imposed on the fiber during handling, cabling, and installation for a given set of environmental conditions. There are three basic scenarios that can lead to strength degradation and failure by inducing flaw growth: dynamic fatigue, static fatigues, and zero-stress aging.
-
Product
NAM (Network Acquisition Module)
-
The NAM is a stable, robust data hub with unrivalled configurability, ideal for large or complex regional and national seismic arrays and other multi station monitoring solutions.
-
Product
Non-contact 3D Optical Profilers
-
LuphoScan platforms are interferometric, scanning metrology systems. They are designed to perform ultra precision non-contact 3D form measurements mainly of rotationally symmetric surfaces such as aspheric lenses.
-
Product
Basic Rate and Primary Rate ISDN Network Simulator
Emutel Duo
-
Emutel Duo is a convenient and flexbile basic rate and primary rate ISDN network simulator. With 3 software selectable S/U interfaces and optional 2 E1/T1 interfaces you can test and develop a full range of ISDN equipment.
-
Product
Optical Tactile Surface Finish
1000Z
-
The Adcole Model 1000-Z features both optical and tactile measuring heads to deliver high precision surface measurements of camshafts, crankshafts and turned parts. The non-contact interferometric probe greatly expands on the measurement capabilities from the diamond tipped contact probe of the standard Adcole 1000 gage, as the optical accessory can precisely measure surface finish of cam track groove sidewalls, cam track bottom grooves and more. Profilometers such as the 1000-Z quantify surface roughness and are relied on to maintain quality and identify potential problems in the manufacturing and coating process.
-
Product
Optical Test And Measurement
-
Any type of fiber optic interconnection requires its interfaces to be free of dust and scratches in order to reach the lowest transmission loss. Small, handheld and battery powered inspection tools are available from AMS Technologies for inspection of fiber optic connectors in the field as well as high resolution type microscopes suitable for use in a production environment for qualifying the endface preparation. Additional S/W tools can support the user in making a quick decision if a certain defect is acceptable or if the surface fault disqualifies it for further use. Small and lightweight test equipment for measurement of the transmitted power in an optical fiber is needed wherever technicians handle optical fibers. Our product portfolio comprises light sources for various wavelengths, power meters for the visible and infrared and integrated solutions for sources and meters as well as optical time domain reflectometers (OTDR) coupled with visible wavelength light sources for easy fault detection within a fiber optic link.
-
Product
Optical Tensiometers
Theta Topography
-
Theta Topography is an innovative system capable of separating the effect of surface roughness to the contact angle result. As a result, roughness-corrected contact angles can be better compared with each other for research and quality control purposes.
-
Product
Saluki S5700 Series Field Comm Analyzer (SA/CA/OPTICAL)
-
S5700 Series Field Comm Analyzer combines the highest performance operating specifications and multi-functional measurements such as cable and antenna system analysis, fiber inspection, spectrum analysis, cellular signal demodulation, interference analysis, signal coverage mapping and RF/optical power measurements in a single instrument.
-
Product
28/45 GHz Dual Optical Channel DCA-M with Option CDR
N1092B
Oscilloscope
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, fast sampling rates for high throughput, and integrated clock recovery available.
-
Product
Fiber Optic Sensors And Fiber Optics
-
Over 350 customized fiber optic solutions. Smaller, more precise, faster. Robust - High-temperature, chemically resistant, mechanically robust glass or plastic fibers. Better performance - Position-independent detection of irregular objects or liquids. Plug & Play - Intuitive parametrization with the Baumer Sensor Suite via IO-Link.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 62.5/125 Fiber
40-852A-318-M62.5
Multiplexer Module
The 40/42-852A-318-M62.5 is a PXI/PXIe 8-channel multiplexer with MU (mini SC) connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. They are also available with an optional hardware interlock which, when activated, will return all optical switches to their default unpowered state.
-
Product
Rolling Seal 8 Optical Connector - APC (RS8 APC)
-
The Angled Physical Contact Rolling Seal 8 Connector (RS8 APC) from Teledyne ODI is a wet-mateable optical connector with angled endfaces. The design reduces signal interference due to reflections at the connector face, supporting the next generation of subsea optical communication equipment. The Rolling Seal design provides isolation from seawater and silt when the connectors are unmated. As the seals rotate, the fibers join inside a clean, oil-filled conduit, resulting in a reliable optical throughput. The RS8 APC incorporates RS8 Mark III design features to enhance operational efficiency and reduce risks during ROV intervention.
-
Product
Network Cable Tester
AVJoG
-
*A two box solution to testing AV panel installations. *Each box only 150mm square.*Easy to use with only one button operation. *LCD display for test results. *All major AV connectors present, no need for extra adaptors. *6V battery or Mains use.
-
Product
Optical Power Meter with Optical Head
GM8012 + 2 X GM8300X
-
The UC8820 + 2 X UC8820X optical power meter with optical head offer superior performance for the test of DWDM components, AWG & PLC components, optical amplifiers, and other general purpose of fiber optical test and measurement applications. It is special design for volume production line application.
